Invacare Top End T-3 manual Adjusting Figure, Adjusting Quad-Release Handles In And/Or Out

Page 33

WHEELS

PROCEDURE 6

 

 

ADJUSTING (FIGURE 4)

Adjusting Quad-Release Handles In And/Or Out.

1.Remove rear wheel and quad-release axle from the chair, refer to REMOVING/INSTALL- ING THE REAR WHEELS in this procedure of the manual.

2.Loosen the locking screw.

3.Make the following adjustments if necessary:

A.If the quad-release handle is not releasing the locking pins completely, rotate the quad-release handle approximately one-quarter (1/4) turn CLOCKWISE.

B.If the quad-release handle hits the spokes of the rear wheel when assembled, rotate the quad-release handle approximately one-quarter (1/4) turn COUNTERCLOCKWISE.

4.Tighten the locking screw.

5.Reinstall rear wheel and quad-release axle onto the chair.

WARNING

Make sure detent pin of the quad-release axle is fully released BEFORE operat- ing the wheelchair.

Keep locking pins clean.

6.Flip handle of the quad-release axle down to release the detent pin ensuring that the locking pins are fully released.

7.Repeat the above procedures until the quad-release axle locks correctly.

Removing Play From Rear Wheels.

1.With the rear wheel and quad-release axle still mounted onto the chair, make the follow- ing adjustment:

A.Tighten length adjusting screw until there is no in and out movement of quad-release axle and rear wheel.

Quad-Release Handle

Locking Pins

Locking

Camber Insert

Screw

 

ADJUSTING QUAD-RELEASE HANDLE

IN OR OUT

REMOVING PLAY

 

FROM THE REAR

 

WHEELS

Length

Reduces Play

Adjustment

 

 

Screw

FIGURE 4 - ADJUSTING QUAD-RELEASE AXLES

WHEELS

Part No. 1054916

33

T-3™ and T-4™ Series

Image 33
Contents Owners Operator And Maintenance Manual Special Notes Special NotesTable of Contents Register Your Product Name Address Complete and mail this formZip/Postal Code Email Phone No Invacare Model No. Serial NoFold here Cut Along Line Typical Product Parameters Typical Product ParametersSee current order form 250 lbs See current order form Stability Procedure General GuidelinesGeneral Guidelines Stability WarningsGeneral Warnings Continuted Weight Training Weight LimitationTire Pressure Stability and Balance SAFETY/HANDLING of WheelchairsPercentage of Weight Distribution Procedure General Guidelines Coping with Everyday ObstaclesFunctional Reach from a Wheelchair Adjustable Models OnlyGuidelines Shortening FrontDo not tilt the chair without assistance TiltingStairways Transferring to and from Other Seats ESCALATORS? SorrySafety Inspection Checklist Safety InspectionSafety Inspection Safety Inspection Checklist Safety Inspection Procedure MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresProcedure Back ADJUSTING/REPLACING Back Upholstery FigureAdjusting Back Upholstery BackReplacing Back Upholstery Folding Back FigureBack Angle Adjustment Figure Back Height Adjustment FigureHole Number 11-14 14-18 16-20Back Angle to Seat Rail Seat Upholstery Replacement Figure Procedure SeatSeat Rear Seat to Floor Range in Inches Rear Seat Height AdjustmentFront Seat Height Adjustment Before Front Seat Height AdjustmentRigid Clothing Guard Replacement Figure Nylon Clothing Guard with Plastic Insert Replacement FigureClothing Guards ClothingProcedure Wheels REMOVING/INSTALLING Rear Wheels FigureWheels Quick or QUAD-RELEASE AxlesREMOVING/INSTALLING Rear Wheels Adjusting QUICK-RELEASE Axles FigureInstalling Figure INSTALLING/ADJUSTING QUAD-RELEASE AxlesAdjusting Figure Adjusting Quad-Release Handles In And/Or OutRemoving Play From Rear Wheels Handrim Replacement Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEDo not inflate tire until handrim is completely assembled OPENING/CLOSING Clamps Figure QUICK-RELEASE Lever Standard Closed PositionOpen Position Detail a Measuring the Centerlines TOP View Determining TOE IN/TOE OUT FigureWheelchair Front WheelchairCamber Inserts Adjusting TOE IN/TOE OUTOr 12 Camber Or 6/12 Camber InsertsWheels Axle Tube Will Rotate UP Only Elite and T-4 Models with Fixed Camber Figure Adjusting Rear Wheel Camber FigureRequired Camber Insert AdjustmentDetail a Measuring Frame Bracket Distance Adjusting Wheelbase Length Adjusting Center GravityAdjusting Wheelbase Width Figure Adjusting Wheelbase Width A-4 Camber TubeCamber Tube Replacing Axle Tube Figure Adjusting Wheelbase Width Camber TubeReplacing Axle Tube Adjusting Front Caster Height Figure Front Caster Replacement FigureInstalling Quick Release Casters Installing QUICK-RELEASE Casters FigureWheel Lock ADJUSTMENT/REPLACEMENT Figure Adjusting the HIGH/LOW Mount Wheel LocksReplacing the HIGH/LOW Mount Wheel Lock Footrest Procedure FootrestWheelchair Frame Mounting Bracket Hex Screw Height Adjustment Procedure Footrest Adjusting FootrestDepth Adjustment Tennis Elite Individual Footplates Before 4/2000 Figures 2Changing Footplate Depth Footrest Procedure Changing Footplate AngleChanging Footplate Height Repositioning FootplateInstalling Footplates Procedure Footrest Removing FootplatesRemoving Footplate System Mounting Clamp Replacing Footplate Mounting Bracket3 Tennis Elite Individual Footplates Footrest ProcedureTennis Adjustable Footrest System Before 4/2000 Figure Adjusting Individual FootplatesReplacing Individual Footplates Replacing Seat Adjustment Weldment Footrest Procedure Replacing Footplate WeldmentProcedure Footrest Optional ANTI-TIPPER Procedure REPLACING/ADJUSTING Fixed ANTI-TIPPER Swivel CasterReplacement Elite and T-4 Elite with Fixed Camber Tube FigureAssembleddisassembled AdjustingINSTALLING/ADJUSTING Removable ANTI-TIPPER OptionalANTI-TIPPER Anti-Tipper Push Mounting Holes Warranty WarrantyCanada