Yamaha PJP-100H owner manual Setting Date and Time, Web menu, click Sntp Server

Page 41

Setting Date and Time

The SNTP server (time distribution server) enables to adjust the date and time information in this unit automatically at constant intervals.

Notes

•The date and time of this unit cannot be adjusted without a SNTP server. In this case, note that the downloaded call history (page 38) does not show correct date and time data.

•If the time data cannot be obtained from the SNTP server at the moment this unit is turned on or the designated SNTP server does not exist at the moment, the time is not displayed on this unit.

•The synchronization with the SNTP server may not be available depending on the security settings of the LAN accommodating this unit. To use an external SNTP server in this case, it is required to change the settings of the router, etc. Refer to the instruction manuals for your router for details.

1In the web menu, click “SNTP Server”.

The “SNTP Server” window appears.

2In the “SNTP Server ID” field, enter the name or IP address of the SNTP server to be used.

3In the “SNTP Synchronization Interval” field, select the desired interval for synchronization with the SNTP server.

4Click “Submit”.

The setting is registered and the top of the web menu reappears.

CONFIGURATIONS

English

37

Image 41

Contents IP audio conference system Important Safty Instractions FCC Information for US customers Iii Contents Settings from the PC FeaturesAudio conference through networks Arrayed microphones and speakers for high audio qualityAbout trademarks Supplied AccessoriesAbout this manual Top panel Controls and FunctionsDC in 12V terminal Right side panelAudio in terminal Audio OUT terminalSerial label OtherSerial terminal Arrayed speakers Bottom panelDisplay 192.168.100.200Menu Address To configure the settings from a PC Preparation ProcedureTo use this unit with a SIP server LAN cableTo exit the standby mode and switch this unit on again Connecting this unitStandby mode If the IP address display is ???.???.???.??? Registering the network settings of this unitObtaining the IP address automatically To check if the correct network information is obtainedSettings Network Settings Sound Settings General Settings Menu Settings Call History OnlineNetwork Settings IP Address Subnet Mask Default Gateway IP ???.???.???.??? Menu AddressSubnet Mask 255.255.255.000 Enable DisableIP Adress 192.168.100.200 Press or to select 3. Default Gateway Then press Default Gateway 000.000.000.000DNS Server 000.000.000.000 Press or to select 4. DNS Server, Then pressTake the positions of the talkers in consideration Installing this unit in the conference roomAbout installation environment Making a Call Menu Address CancelCalling another unit by specifying an IP address 192.168.100.20To mute the microphone 192.168.0.10To make a call involving multiple Locations Address Book Headquarter Branch a Branch B Calling another unit using the address bookCalling another unit in online status Online 192.168.0.20Calling another unit using the call history Online 192.168.0.20 CancelCall History Headquarter Branch a Press or to select 2. Call History, Then pressCall History Headquater Branch a CancelWhile having an incoming call, press Answering a CallTo deny the call Carry out the procedure in Answering a Call Carry out one of the following procedure during a callTalking with Multiple Locations To call another location during a callWhen Speaker Mode is other than Divide When Speaker Mode is set to Divide192.168.100.20 192.168.100.30 Menu Address 192.168.100.20 192.168.100.30 192.168.100.40 Menu AddressPress or to select 4. Change location Then press Change Location 192.168.100.20 192.168.100.30 Menu AddressPress during call Press or to select the menu category Then press Configuring SettingsConfiguring settings using the keys on this unit To return to the previous menu without saving the setting Configuring settings using the web menuTo confirm the setting, press Change the parameterManaging address book information Setting Menu ListConfiguring network settings Configuring the connection mode Configuring the Dhcp server settingsConfiguring the NAT traversal setting Configuring the SIP server settingSelecting the audio pickup area Microphone mode Configuring sound settingsConfiguring the speaker mode Using the web menuConfiguring the audio connection function Configuring the room sizeConfiguring the external input/output Setting Configuring general settings Storing the call history Setting the passwordRestoring the factory settings Registering a new address Editing Address BookEditing an existing address Deleting an address Registering the SIP server information Using the SIP ServerWeb menu, click SIP Server Click SubmitTokyohq@sales.yama 2006.05 09 48 Menu Address Display in SIP server operationCalling another unit by dialing the user Initial displayWeb menu, click Sntp Server Setting Date and TimeViewing the call history file Contents of call history fileManaging the Call History Confirming the System Log Message of This Unit syslog Web menu, click Syslog SettingMaximum number of locations by Cascade connection What is cascade connection ?Display in cascade connection Configure the setting of the cascade serverConfigure the settings Cascade clients Software Licensing Agreement Updating the FirmwareFirmware Update ver. DT1.12-V1.6x Yes 2. No Settings General Settings Restore Settings Firmware UpdateFirmware update process takes a few minutes to complete When the firmware update is completeUpdating the firmware manually Press To cancel the firmware updateQ1 LED indicators do not light up TroubleshootingWeb menu cannot be opened Q2 Web menu setting is not availableCall cannot be originated Q3 Call is impossibleAudio is interrupted Q4 Other problemsRestore Settings Yes 2. No Resetting the UnitResetting using the keys on this unit To cancel resetting in the middleClick Restore Factory Settings Resetting using the web menuWeb menu, click Restore Factory Settings Obtaining the audio characteristic information Obtaining the Setting Information for Support on this UnitClick Download Setting Information in the web menu Click SaveSpecifications Page All rights reserved