Yamaha PJP-100H owner manual Preparation Procedure, To configure the settings from a PC, LAN cable

Page 12

Preparation Procedure

The following preparation steps should be completed before using this unit.

Step 1: (page 9)

Connecting this unit to the network and turning this unit on

Step 2: (page 10)

Registering the network settings of this unit

The setting method is variable depending on whether or not the network uses the DHCP server.

Step 3: (page 14)

Installing this unit in the conference room

To configure the settings from a PC

This section describes the preparation method using the keys on this unit, but the same settings are also available by accessing the “Web Settings Page” from a PC. See “Configuring settings using the web menu” (page 25) for details.

Note

Some functions such as the address book setting cannot be set using the keys on this unit alone.

To use this unit with a SIP server

The settings have to be performed by accessing the “Web Settings Page” from a PC. See “Registering the SIP server information” (page 35) for details.

Notes on system connection

Please check the following before proceeding to preparation.

LAN cable

Prepare a 10BASE-T or 100BASE-TX LAN cable.

Information on the network accommodating this unit

Obtain or decide the following information prior to installation of this unit.

IP address and subnet mask settings of this unit

IP addresses of the default gateway and DNS server used by this unit

Notes on the network accommodating this unit

When using this unit in the Internet, it is basically required to obtain a global IP address.

When using this unit in a corporate LAN, it cannot be connected to equipment outside the firewall. However, as calls may become possible by changing the settings of the router, please consult your network administrator for details. This unit uses a port number of 5060 (UDP) for SIP, and 57000 to 57010 (UDP) for RTP/RTCP.

To prevent the audio from being interrupted, it is recommended to use a network that can offer enough transmission bandwidths. See “Specifications” (page 53) for details.

If “CODEC Line Adapt” (page 31) is set to “Enable” and the allocation of transmission bandwidth descends during a call, this unit selects the optimum encoding method for the network situations automatically.

8

Image 12
Contents IP audio conference system Important Safty Instractions FCC Information for US customers Iii Contents Features Settings from the PCAudio conference through networks Arrayed microphones and speakers for high audio qualitySupplied Accessories About this manualAbout trademarks Controls and Functions Top panelRight side panel DC in 12V terminalAudio in terminal Audio OUT terminalOther Serial labelSerial terminal Arrayed speakers Bottom panel192.168.100.200 Menu AddressDisplay Preparation Procedure To configure the settings from a PCTo use this unit with a SIP server LAN cableConnecting this unit Standby modeTo exit the standby mode and switch this unit on again Registering the network settings of this unit If the IP address display is ???.???.???.???Obtaining the IP address automatically To check if the correct network information is obtainedMenu Settings Call History Online Settings Network Settings Sound Settings General SettingsNetwork Settings IP Address Subnet Mask Default Gateway IP ???.???.???.??? Menu AddressEnable Disable IP Adress 192.168.100.200Subnet Mask 255.255.255.000 Default Gateway 000.000.000.000 Press or to select 3. Default Gateway Then pressDNS Server 000.000.000.000 Press or to select 4. DNS Server, Then pressInstalling this unit in the conference room About installation environmentTake the positions of the talkers in consideration Menu Address Cancel Making a CallCalling another unit by specifying an IP address 192.168.100.20192.168.0.10 To make a call involving multiple LocationsTo mute the microphone Calling another unit using the address book Address Book Headquarter Branch a Branch BCalling another unit in online status Online 192.168.0.20Online 192.168.0.20 Cancel Calling another unit using the call historyCall History Headquarter Branch a Press or to select 2. Call History, Then pressBranch a Cancel Call History HeadquaterAnswering a Call To deny the callWhile having an incoming call, press Carry out one of the following procedure during a call Carry out the procedure in Answering a CallTalking with Multiple Locations To call another location during a callWhen Speaker Mode is set to Divide When Speaker Mode is other than Divide192.168.100.20 192.168.100.30 Menu Address 192.168.100.20 192.168.100.30 192.168.100.40 Menu AddressChange Location 192.168.100.20 192.168.100.30 Menu Address Press during callPress or to select 4. Change location Then press Configuring Settings Configuring settings using the keys on this unitPress or to select the menu category Then press Configuring settings using the web menu To return to the previous menu without saving the settingTo confirm the setting, press Change the parameterSetting Menu List Configuring network settingsManaging address book information Configuring the Dhcp server settings Configuring the connection modeConfiguring the NAT traversal setting Configuring the SIP server settingConfiguring sound settings Selecting the audio pickup area Microphone modeUsing the web menu Configuring the speaker modeConfiguring the room size Configuring the external input/output SettingConfiguring the audio connection function Configuring general settings Setting the password Restoring the factory settingsStoring the call history Editing Address Book Registering a new addressEditing an existing address Deleting an address Using the SIP Server Registering the SIP server informationWeb menu, click SIP Server Click SubmitDisplay in SIP server operation Tokyohq@sales.yama 2006.05 09 48 Menu AddressCalling another unit by dialing the user Initial displaySetting Date and Time Web menu, click Sntp ServerContents of call history file Managing the Call HistoryViewing the call history file Web menu, click Syslog Setting Confirming the System Log Message of This Unit syslogWhat is cascade connection ? Maximum number of locations by Cascade connectionConfigure the setting of the cascade server Configure the settings Cascade clientsDisplay in cascade connection Updating the Firmware Software Licensing AgreementSettings General Settings Restore Settings Firmware Update Firmware Update ver. DT1.12-V1.6x Yes 2. NoFirmware update process takes a few minutes to complete When the firmware update is completeUpdating the firmware manually To cancel the firmware update PressTroubleshooting Q1 LED indicators do not light upQ2 Web menu setting is not available Web menu cannot be openedQ3 Call is impossible Call cannot be originatedQ4 Other problems Audio is interruptedResetting the Unit Restore Settings Yes 2. NoResetting using the keys on this unit To cancel resetting in the middleResetting using the web menu Web menu, click Restore Factory SettingsClick Restore Factory Settings Obtaining the Setting Information for Support on this Unit Obtaining the audio characteristic informationClick Download Setting Information in the web menu Click SaveSpecifications Page All rights reserved