Yamaha PJP-100H owner manual Settings General Settings Restore Settings Firmware Update

Page 47

Updating the firmware automatically

Follow the procedure below to install the latest firmware automatically.

Notes

•Automatic firmware update can be performed only if this unit can be connected to the internet. If not, follow the procedure in “Updating the firmware manually” (page 44).

•Once the firmware update is started, do not perform any other operation until update is completed and this unit is restarted. If the update operation is interrupted, this unit may become unusable, in which case this unit needs to be returned to the factory to repair.

•When the firmware update is completed, this unit is restarted automatically. All of the calls being connected are disconnected at this time.

•Do not unplug the LAN cable during the firmware update. Otherwise, this unit could become unusable and may need to be returned to the factory to repair.

y

You can specify any URL to download the firmware (page 44).

 

 

Updating the Firmware

 

 

 

3 Press

, and then press or to select

“5. Firmware Update”.

Settings

3.General Settings

4.Restore Settings

5. Firmware Update

4Press .

The “Firmware Update” menu appears.

Firmware Update ver. DT1.12-V1.6x

1.Yes 2. No

1

2

3

4

5

6

7

8

9

 

0

 

 

MIC MUTE

VOL

DC IN 12V IN AUDIO OUT LAN

5 Press or to select “1. Yes”, and then

press .

This unit is connected to the internet and downloads the latest firmware. When downloading is completed, the firmware update is automatically started.

CONFIGURATIONS

1

Press

in the initial display.

 

 

The menu display appears.

 

 

 

 

 

2

Press

or

to select “1. Settings”, and

 

 

then press

.

 

 

The “Settings” menu appears.

Settings

1. Network Settings

2.Sound Settings

3.General Settings

The firmware update process takes a few minutes to complete.

MIC MUTE (red LED) on the top panel of this unit flashes during the firmware update process. Do not turn this unit off while MIC MUTE (red LED) flashes.

■When the firmware update is complete

This unit restarts automatically.

Check the version number in the “Program Version” field on the top of the web menu to confirm that the new firmware is installed properly.

English

43

Page 46 Page 48
Image 47
Page 46 Page 48
Contents IP audio conference system Important Safty Instractions FCC Information for US customers Iii Contents Arrayed microphones and speakers for high audio quality FeaturesSettings from the PC Audio conference through networksAbout trademarks Supplied AccessoriesAbout this manual Top panel Controls and FunctionsAudio OUT terminal Right side panelDC in 12V terminal Audio in terminalArrayed speakers Bottom panel OtherSerial label Serial terminalDisplay 192.168.100.200Menu Address LAN cable Preparation ProcedureTo configure the settings from a PC To use this unit with a SIP serverTo exit the standby mode and switch this unit on again Connecting this unitStandby mode To check if the correct network information is obtained Registering the network settings of this unitIf the IP address display is ???.???.???.??? Obtaining the IP address automaticallyIP ???.???.???.??? Menu Address Menu Settings Call History OnlineSettings Network Settings Sound Settings General Settings Network Settings IP Address Subnet Mask Default GatewaySubnet Mask 255.255.255.000 Enable DisableIP Adress 192.168.100.200 Press or to select 4. DNS Server, Then press Default Gateway 000.000.000.000Press or to select 3. Default Gateway Then press DNS Server 000.000.000.000Take the positions of the talkers in consideration Installing this unit in the conference roomAbout installation environment 192.168.100.20 Menu Address CancelMaking a Call Calling another unit by specifying an IP addressTo mute the microphone 192.168.0.10To make a call involving multiple Locations Online 192.168.0.20 Calling another unit using the address bookAddress Book Headquarter Branch a Branch B Calling another unit in online statusPress or to select 2. Call History, Then press Online 192.168.0.20 CancelCalling another unit using the call history Call History Headquarter Branch aCall History Headquater Branch a CancelWhile having an incoming call, press Answering a CallTo deny the call To call another location during a call Carry out one of the following procedure during a callCarry out the procedure in Answering a Call Talking with Multiple Locations192.168.100.20 192.168.100.30 192.168.100.40 Menu Address When Speaker Mode is set to DivideWhen Speaker Mode is other than Divide 192.168.100.20 192.168.100.30 Menu AddressPress or to select 4. Change location Then press Change Location 192.168.100.20 192.168.100.30 Menu AddressPress during call Press or to select the menu category Then press Configuring SettingsConfiguring settings using the keys on this unit Change the parameter Configuring settings using the web menuTo return to the previous menu without saving the setting To confirm the setting, pressManaging address book information Setting Menu ListConfiguring network settings Configuring the SIP server setting Configuring the Dhcp server settingsConfiguring the connection mode Configuring the NAT traversal settingSelecting the audio pickup area Microphone mode Configuring sound settingsConfiguring the speaker mode Using the web menuConfiguring the audio connection function Configuring the room sizeConfiguring the external input/output Setting Configuring general settings Storing the call history Setting the passwordRestoring the factory settings Registering a new address Editing Address BookEditing an existing address Deleting an address Click Submit Using the SIP ServerRegistering the SIP server information Web menu, click SIP ServerInitial display Display in SIP server operationTokyohq@sales.yama 2006.05 09 48 Menu Address Calling another unit by dialing the userWeb menu, click Sntp Server Setting Date and TimeViewing the call history file Contents of call history fileManaging the Call History Confirming the System Log Message of This Unit syslog Web menu, click Syslog SettingMaximum number of locations by Cascade connection What is cascade connection ?Display in cascade connection Configure the setting of the cascade serverConfigure the settings Cascade clients Software Licensing Agreement Updating the FirmwareWhen the firmware update is complete Settings General Settings Restore Settings Firmware UpdateFirmware Update ver. DT1.12-V1.6x Yes 2. No Firmware update process takes a few minutes to completeUpdating the firmware manually Press To cancel the firmware updateQ1 LED indicators do not light up TroubleshootingWeb menu cannot be opened Q2 Web menu setting is not availableCall cannot be originated Q3 Call is impossibleAudio is interrupted Q4 Other problemsTo cancel resetting in the middle Resetting the UnitRestore Settings Yes 2. No Resetting using the keys on this unitClick Restore Factory Settings Resetting using the web menuWeb menu, click Restore Factory Settings Click Save Obtaining the Setting Information for Support on this UnitObtaining the audio characteristic information Click Download Setting Information in the web menuSpecifications Page All rights reserved
Top Page Image Contents