Yamaha PJP-100H owner manual Press, To cancel the firmware update

Page 49

2Start “Command Prompt” in the Windows PC

which can access the web menu of this unit.

When using Windows XP, select the “Start” menu → “All Program” → “Accessories” → “Command Prompt”.

3Enter and run the following command. tftp -i [IP address of this unit] put [file name of the firmware]

Example:

tftp -i 192.168.0.6 put pjp_100h_113.bin

The confirmation of the firmware version is required.

4Press .

The confirmation whether the firmware update is carried out is required.

5Press .

When the installation is complete, the firmware update process starts automatically.

The firmware update process takes a few minutes to complete.

MIC MUTE (red LED) on the top panel of this unit flashes during the firmware update process. Do not turn this unit off while MIC MUTE (red LED) flashes.

To cancel the firmware update

In step 5, press .

■When the firmware update is complete

This unit restarts automatically.

Check the version number in the “Program Version” field on the top of the web menu to confirm that the new firmware is installed properly.

Updating the Firmware

CONFIGURATIONS

English

45

Image 49

Contents IP audio conference system Important Safty Instractions FCC Information for US customers Iii Contents Settings from the PC FeaturesAudio conference through networks Arrayed microphones and speakers for high audio qualityAbout this manual Supplied AccessoriesAbout trademarks Top panel Controls and FunctionsDC in 12V terminal Right side panelAudio in terminal Audio OUT terminalSerial label OtherSerial terminal Arrayed speakers Bottom panelMenu Address 192.168.100.200Display To configure the settings from a PC Preparation ProcedureTo use this unit with a SIP server LAN cableStandby mode Connecting this unitTo exit the standby mode and switch this unit on again If the IP address display is ???.???.???.??? Registering the network settings of this unitObtaining the IP address automatically To check if the correct network information is obtainedSettings Network Settings Sound Settings General Settings Menu Settings Call History OnlineNetwork Settings IP Address Subnet Mask Default Gateway IP ???.???.???.??? Menu AddressIP Adress 192.168.100.200 Enable DisableSubnet Mask 255.255.255.000 Press or to select 3. Default Gateway Then press Default Gateway 000.000.000.000DNS Server 000.000.000.000 Press or to select 4. DNS Server, Then pressAbout installation environment Installing this unit in the conference roomTake the positions of the talkers in consideration Making a Call Menu Address CancelCalling another unit by specifying an IP address 192.168.100.20To make a call involving multiple Locations 192.168.0.10To mute the microphone Address Book Headquarter Branch a Branch B Calling another unit using the address bookCalling another unit in online status Online 192.168.0.20Calling another unit using the call history Online 192.168.0.20 CancelCall History Headquarter Branch a Press or to select 2. Call History, Then pressCall History Headquater Branch a CancelTo deny the call Answering a CallWhile having an incoming call, press Carry out the procedure in Answering a Call Carry out one of the following procedure during a callTalking with Multiple Locations To call another location during a callWhen Speaker Mode is other than Divide When Speaker Mode is set to Divide192.168.100.20 192.168.100.30 Menu Address 192.168.100.20 192.168.100.30 192.168.100.40 Menu AddressPress during call Change Location 192.168.100.20 192.168.100.30 Menu AddressPress or to select 4. Change location Then press Configuring settings using the keys on this unit Configuring SettingsPress or to select the menu category Then press To return to the previous menu without saving the setting Configuring settings using the web menuTo confirm the setting, press Change the parameterConfiguring network settings Setting Menu ListManaging address book information Configuring the connection mode Configuring the Dhcp server settingsConfiguring the NAT traversal setting Configuring the SIP server settingSelecting the audio pickup area Microphone mode Configuring sound settingsConfiguring the speaker mode Using the web menuConfiguring the external input/output Setting Configuring the room sizeConfiguring the audio connection function Configuring general settings Restoring the factory settings Setting the passwordStoring the call history Registering a new address Editing Address BookEditing an existing address Deleting an address Registering the SIP server information Using the SIP ServerWeb menu, click SIP Server Click SubmitTokyohq@sales.yama 2006.05 09 48 Menu Address Display in SIP server operationCalling another unit by dialing the user Initial displayWeb menu, click Sntp Server Setting Date and TimeManaging the Call History Contents of call history fileViewing the call history file Confirming the System Log Message of This Unit syslog Web menu, click Syslog SettingMaximum number of locations by Cascade connection What is cascade connection ?Configure the settings Cascade clients Configure the setting of the cascade serverDisplay in cascade connection Software Licensing Agreement Updating the FirmwareFirmware Update ver. DT1.12-V1.6x Yes 2. No Settings General Settings Restore Settings Firmware UpdateFirmware update process takes a few minutes to complete When the firmware update is completeUpdating the firmware manually Press To cancel the firmware updateQ1 LED indicators do not light up TroubleshootingWeb menu cannot be opened Q2 Web menu setting is not availableCall cannot be originated Q3 Call is impossibleAudio is interrupted Q4 Other problemsRestore Settings Yes 2. No Resetting the UnitResetting using the keys on this unit To cancel resetting in the middleWeb menu, click Restore Factory Settings Resetting using the web menuClick Restore Factory Settings Obtaining the audio characteristic information Obtaining the Setting Information for Support on this UnitClick Download Setting Information in the web menu Click SaveSpecifications Page All rights reserved