Yamaha PJP-100H Using the SIP Server, Registering the SIP server information, Click Submit

Page 39

Using the SIP Server

Registering the SIP server information

When this unit is used in an environment with a SIP server, the address of the SIP server to be referenced by this unit and the SIP address of this unit should be registered. If password authentication is required for accessing the desired SIP server, it is also necessary to enter the password. Consult your system administrator for details.

Note

The settings described in this section are not required if this unit is used in an environment without SIP server.

1In the web menu, click “SIP Server”.

The “SIP Server” window appears.

2In the “SIP Server” field, click “Enable”.

3In the “SIP Server Name” field, enter the name or IP address of the SIP server.

4If password authentication is required for accessing the desired SIP server, enter the authentication password for the SIP server in the “SIP URI Password” field.

5In the “SIP URI” field, enter the SIP address to be set to this unit.

Enter the SIP address in the format “sip:(sip address)”.

Example: sip:sipuser@yamaha.co.jp

6Click “Submit”.

The setting is registered and the top window of the web menu reappears.

Notes on SIP server operation

•To connect a call using the SIP server, the SIP address of this unit should be registered in the SIP server.

•It is not possible to establish a connection between a PJP unit that uses the SIP address and a PJP unit that uses the IP address.

•If the SIP server is installed outside the LAN, it is required to use the NAT transversal function (page 27) of this unit.

Branch A	Branch B
Router	Router
	Router

SIP server

Headquarter

In this case, the following conditions are required.

•The router to which the PJP is connected supports the UPnP function.

•A global IP address is assigned to the WAN on the router side.

Note

When a SIP call is connected using the NAT transversal function, it is not possible to install multiple PJP units in a single segment and connect a call between them.

CONFIGURATIONS

English

35

Image 39

Contents IP audio conference system Important Safty Instractions FCC Information for US customers Iii Contents Arrayed microphones and speakers for high audio quality FeaturesSettings from the PC Audio conference through networksSupplied Accessories About this manualAbout trademarks Top panel Controls and FunctionsAudio OUT terminal Right side panelDC in 12V terminal Audio in terminalArrayed speakers Bottom panel OtherSerial label Serial terminal192.168.100.200 Menu AddressDisplay LAN cable Preparation ProcedureTo configure the settings from a PC To use this unit with a SIP serverConnecting this unit Standby modeTo exit the standby mode and switch this unit on again To check if the correct network information is obtained Registering the network settings of this unitIf the IP address display is ???.???.???.??? Obtaining the IP address automaticallyIP ???.???.???.??? Menu Address Menu Settings Call History OnlineSettings Network Settings Sound Settings General Settings Network Settings IP Address Subnet Mask Default GatewayEnable Disable IP Adress 192.168.100.200Subnet Mask 255.255.255.000 Press or to select 4. DNS Server, Then press Default Gateway 000.000.000.000Press or to select 3. Default Gateway Then press DNS Server 000.000.000.000Installing this unit in the conference room About installation environmentTake the positions of the talkers in consideration 192.168.100.20 Menu Address CancelMaking a Call Calling another unit by specifying an IP address192.168.0.10 To make a call involving multiple LocationsTo mute the microphone Online 192.168.0.20 Calling another unit using the address bookAddress Book Headquarter Branch a Branch B Calling another unit in online statusPress or to select 2. Call History, Then press Online 192.168.0.20 CancelCalling another unit using the call history Call History Headquarter Branch aCall History Headquater Branch a CancelAnswering a Call To deny the callWhile having an incoming call, press To call another location during a call Carry out one of the following procedure during a callCarry out the procedure in Answering a Call Talking with Multiple Locations192.168.100.20 192.168.100.30 192.168.100.40 Menu Address When Speaker Mode is set to DivideWhen Speaker Mode is other than Divide 192.168.100.20 192.168.100.30 Menu AddressChange Location 192.168.100.20 192.168.100.30 Menu Address Press during callPress or to select 4. Change location Then press Configuring Settings Configuring settings using the keys on this unitPress or to select the menu category Then press Change the parameter Configuring settings using the web menuTo return to the previous menu without saving the setting To confirm the setting, pressSetting Menu List Configuring network settingsManaging address book information Configuring the SIP server setting Configuring the Dhcp server settingsConfiguring the connection mode Configuring the NAT traversal settingSelecting the audio pickup area Microphone mode Configuring sound settingsConfiguring the speaker mode Using the web menuConfiguring the room size Configuring the external input/output SettingConfiguring the audio connection function Configuring general settings Setting the password Restoring the factory settingsStoring the call history Registering a new address Editing Address BookEditing an existing address Deleting an address Click Submit Using the SIP ServerRegistering the SIP server information Web menu, click SIP ServerInitial display Display in SIP server operationTokyohq@sales.yama 2006.05 09 48 Menu Address Calling another unit by dialing the userWeb menu, click Sntp Server Setting Date and TimeContents of call history file Managing the Call HistoryViewing the call history file Confirming the System Log Message of This Unit syslog Web menu, click Syslog SettingMaximum number of locations by Cascade connection What is cascade connection ?Configure the setting of the cascade server Configure the settings Cascade clientsDisplay in cascade connection Software Licensing Agreement Updating the FirmwareWhen the firmware update is complete Settings General Settings Restore Settings Firmware UpdateFirmware Update ver. DT1.12-V1.6x Yes 2. No Firmware update process takes a few minutes to completeUpdating the firmware manually Press To cancel the firmware updateQ1 LED indicators do not light up TroubleshootingWeb menu cannot be opened Q2 Web menu setting is not availableCall cannot be originated Q3 Call is impossibleAudio is interrupted Q4 Other problemsTo cancel resetting in the middle Resetting the UnitRestore Settings Yes 2. No Resetting using the keys on this unitResetting using the web menu Web menu, click Restore Factory SettingsClick Restore Factory Settings Click Save Obtaining the Setting Information for Support on this UnitObtaining the audio characteristic information Click Download Setting Information in the web menuSpecifications Page All rights reserved