Yamaha PJP-100H Answering a Call, To deny the call, While having an incoming call, press

Page 24

Answering a Call

Follow the procedure below to answer a call from another unit.

1While having an incoming call, press .

When there is an incoming call, the back light of the display lights up and the ringing tone is generated. The display shows the IP address of the unit calling this unit.

IP: 192.168.0.10 192.168.100.10

Menu :Address

y

If the call is made by the PJP unit which is already registered in the address book, the name registered for the unit is displayed instead of the IP address.

To mute the microphone

When you want to talk about a topic that you do not want to be heard by the other unit(s) involved in the call, press MIC MUTE. The microphones of this unit are turned off while the MIC MUTE LED lights up. To cancel muting, press MIC MUTE again so that the MIC MUTE LED turns off.

y

The microphone indicators (blue LEDs) do not light up while the microphones are muted.

To deny the call

While having an incoming call, press .

Note

Do not disconnect the LAN cable or power cable during a call. Doing so may cause malfunction.

2To adjust the speaker volume, press VOL +/–.

3To disconnect the call when the conference

is complete, press .

20

Image 24
Contents IP audio conference system Important Safty Instractions FCC Information for US customers Iii Contents Features Settings from the PCAudio conference through networks Arrayed microphones and speakers for high audio qualitySupplied Accessories About this manualAbout trademarks Controls and Functions Top panelRight side panel DC in 12V terminalAudio in terminal Audio OUT terminalOther Serial labelSerial terminal Arrayed speakers Bottom panel192.168.100.200 Menu AddressDisplay Preparation Procedure To configure the settings from a PCTo use this unit with a SIP server LAN cableConnecting this unit Standby modeTo exit the standby mode and switch this unit on again Registering the network settings of this unit If the IP address display is ???.???.???.???Obtaining the IP address automatically To check if the correct network information is obtainedMenu Settings Call History Online Settings Network Settings Sound Settings General SettingsNetwork Settings IP Address Subnet Mask Default Gateway IP ???.???.???.??? Menu AddressEnable Disable IP Adress 192.168.100.200Subnet Mask 255.255.255.000 Default Gateway 000.000.000.000 Press or to select 3. Default Gateway Then pressDNS Server 000.000.000.000 Press or to select 4. DNS Server, Then pressInstalling this unit in the conference room About installation environmentTake the positions of the talkers in consideration Menu Address Cancel Making a CallCalling another unit by specifying an IP address 192.168.100.20192.168.0.10 To make a call involving multiple LocationsTo mute the microphone Calling another unit using the address book Address Book Headquarter Branch a Branch BCalling another unit in online status Online 192.168.0.20Online 192.168.0.20 Cancel Calling another unit using the call historyCall History Headquarter Branch a Press or to select 2. Call History, Then pressBranch a Cancel Call History HeadquaterAnswering a Call To deny the callWhile having an incoming call, press Carry out one of the following procedure during a call Carry out the procedure in Answering a CallTalking with Multiple Locations To call another location during a callWhen Speaker Mode is set to Divide When Speaker Mode is other than Divide192.168.100.20 192.168.100.30 Menu Address 192.168.100.20 192.168.100.30 192.168.100.40 Menu AddressChange Location 192.168.100.20 192.168.100.30 Menu Address Press during callPress or to select 4. Change location Then press Configuring Settings Configuring settings using the keys on this unitPress or to select the menu category Then press Configuring settings using the web menu To return to the previous menu without saving the settingTo confirm the setting, press Change the parameterSetting Menu List Configuring network settingsManaging address book information Configuring the Dhcp server settings Configuring the connection modeConfiguring the NAT traversal setting Configuring the SIP server settingConfiguring sound settings Selecting the audio pickup area Microphone modeUsing the web menu Configuring the speaker modeConfiguring the room size Configuring the external input/output SettingConfiguring the audio connection function Configuring general settings Setting the password Restoring the factory settingsStoring the call history Editing Address Book Registering a new addressEditing an existing address Deleting an address Using the SIP Server Registering the SIP server informationWeb menu, click SIP Server Click SubmitDisplay in SIP server operation Tokyohq@sales.yama 2006.05 09 48 Menu AddressCalling another unit by dialing the user Initial displaySetting Date and Time Web menu, click Sntp ServerContents of call history file Managing the Call HistoryViewing the call history file Web menu, click Syslog Setting Confirming the System Log Message of This Unit syslogWhat is cascade connection ? Maximum number of locations by Cascade connectionConfigure the setting of the cascade server Configure the settings Cascade clientsDisplay in cascade connection Updating the Firmware Software Licensing AgreementSettings General Settings Restore Settings Firmware Update Firmware Update ver. DT1.12-V1.6x Yes 2. NoFirmware update process takes a few minutes to complete When the firmware update is completeUpdating the firmware manually To cancel the firmware update PressTroubleshooting Q1 LED indicators do not light upQ2 Web menu setting is not available Web menu cannot be openedQ3 Call is impossible Call cannot be originatedQ4 Other problems Audio is interruptedResetting the Unit Restore Settings Yes 2. NoResetting using the keys on this unit To cancel resetting in the middleResetting using the web menu Web menu, click Restore Factory SettingsClick Restore Factory Settings Obtaining the Setting Information for Support on this Unit Obtaining the audio characteristic informationClick Download Setting Information in the web menu Click SaveSpecifications Page All rights reserved