Yamaha PJP-100H owner manual Updating the Firmware, Software Licensing Agreement

Page 46

Updating the Firmware

You can download the firmware (program to control the functions of this unit) to use the latest features. There are two ways to install the firmware: the one is that you connect to the internet using this unit and automatically install the latest firmware to this unit. The other is that you download the firmware to your PC and install it to this unit manually (page 44).

Software Licensing Agreement

To use the revision upgrading function, you should accept the following software licensing agreement.

1 Permission of use

The present Software Licensing Agreement is intended to allow Yamaha Corporation (hereinafter referred to as “Yamaha”) to permit you to use the firmware (hereinafter “this program”) for Yamaha IP audio conference system (hereinafter “this product”). You can download this program after having accepted the terms and conditions of the present Software Licensing Agreement.

The present Software Licensing Agreement is applicable to the downloaded copy of this program as well as to its duplicates produced in accordance with the present Software Licensing Agreement.

2 Inhibition of redistribution

You are permitted to download this program only when you are intended to upgrade the functions of this product. It is inhibited to upload or post this program in a website accessible by an unspecified number of the general public unless there is a permission from Yamaha.

3 Production of duplicates

You may not produce duplicates of this program unless when it is necessary for backing up purpose or for upgrading of more than one of this product.

4Inhibition of decompiling, reverse engineering or disassembling

You may not decompile, reverse-engineer, disassemble, alter, permit the use of, distribute or create any derivative works of this program

5 Limitation of liabilities

Under any situation including a negligence of its own, Yamaha will not assume any liabilities on the damage to the customers caused by the present Software Licensing Agreement.

6 Export control

You shall comply with all applicable export laws and regulations of any relevant countries including but not limited to Japan and your country. You shall not, directly or indirectly, export or re-export this program except in compliance with such laws and regulations.

7 Compliance to laws and regulations

This Software Licensing Agreement should be compliant to the laws and regulations of Japan and your country, and should be interpreted in accordance with the laws of Japan.

42

Page 45 Page 47
Image 46
Page 45 Page 47
Contents IP audio conference system Important Safty Instractions FCC Information for US customers Iii Contents Audio conference through networks FeaturesSettings from the PC Arrayed microphones and speakers for high audio qualityAbout this manual Supplied AccessoriesAbout trademarks Controls and Functions Top panelAudio in terminal Right side panelDC in 12V terminal Audio OUT terminalSerial terminal OtherSerial label Arrayed speakers Bottom panelMenu Address 192.168.100.200Display To use this unit with a SIP server Preparation ProcedureTo configure the settings from a PC LAN cableStandby mode Connecting this unitTo exit the standby mode and switch this unit on again Obtaining the IP address automatically Registering the network settings of this unitIf the IP address display is ???.???.???.??? To check if the correct network information is obtainedNetwork Settings IP Address Subnet Mask Default Gateway Menu Settings Call History OnlineSettings Network Settings Sound Settings General Settings IP ???.???.???.??? Menu AddressIP Adress 192.168.100.200 Enable DisableSubnet Mask 255.255.255.000 DNS Server 000.000.000.000 Default Gateway 000.000.000.000Press or to select 3. Default Gateway Then press Press or to select 4. DNS Server, Then pressAbout installation environment Installing this unit in the conference roomTake the positions of the talkers in consideration Calling another unit by specifying an IP address Menu Address CancelMaking a Call 192.168.100.20To make a call involving multiple Locations 192.168.0.10To mute the microphone Calling another unit in online status Calling another unit using the address bookAddress Book Headquarter Branch a Branch B Online 192.168.0.20Call History Headquarter Branch a Online 192.168.0.20 CancelCalling another unit using the call history Press or to select 2. Call History, Then pressBranch a Cancel Call History HeadquaterTo deny the call Answering a CallWhile having an incoming call, press Talking with Multiple Locations Carry out one of the following procedure during a callCarry out the procedure in Answering a Call To call another location during a call192.168.100.20 192.168.100.30 Menu Address When Speaker Mode is set to DivideWhen Speaker Mode is other than Divide 192.168.100.20 192.168.100.30 192.168.100.40 Menu AddressPress during call Change Location 192.168.100.20 192.168.100.30 Menu AddressPress or to select 4. Change location Then press Configuring settings using the keys on this unit Configuring SettingsPress or to select the menu category Then press To confirm the setting, press Configuring settings using the web menuTo return to the previous menu without saving the setting Change the parameterConfiguring network settings Setting Menu ListManaging address book information Configuring the NAT traversal setting Configuring the Dhcp server settingsConfiguring the connection mode Configuring the SIP server settingConfiguring sound settings Selecting the audio pickup area Microphone modeUsing the web menu Configuring the speaker modeConfiguring the external input/output Setting Configuring the room sizeConfiguring the audio connection function Configuring general settings Restoring the factory settings Setting the passwordStoring the call history Editing Address Book Registering a new addressEditing an existing address Deleting an address Web menu, click SIP Server Using the SIP ServerRegistering the SIP server information Click SubmitCalling another unit by dialing the user Display in SIP server operationTokyohq@sales.yama 2006.05 09 48 Menu Address Initial displaySetting Date and Time Web menu, click Sntp ServerManaging the Call History Contents of call history fileViewing the call history file Web menu, click Syslog Setting Confirming the System Log Message of This Unit syslogWhat is cascade connection ? Maximum number of locations by Cascade connectionConfigure the settings Cascade clients Configure the setting of the cascade serverDisplay in cascade connection Updating the Firmware Software Licensing AgreementFirmware update process takes a few minutes to complete Settings General Settings Restore Settings Firmware UpdateFirmware Update ver. DT1.12-V1.6x Yes 2. No When the firmware update is completeUpdating the firmware manually To cancel the firmware update PressTroubleshooting Q1 LED indicators do not light upQ2 Web menu setting is not available Web menu cannot be openedQ3 Call is impossible Call cannot be originatedQ4 Other problems Audio is interruptedResetting using the keys on this unit Resetting the UnitRestore Settings Yes 2. No To cancel resetting in the middleWeb menu, click Restore Factory Settings Resetting using the web menuClick Restore Factory Settings Click Download Setting Information in the web menu Obtaining the Setting Information for Support on this UnitObtaining the audio characteristic information Click SaveSpecifications Page All rights reserved
Top Page Image Contents