Yamaha PJP-100H owner manual Q2 Web menu setting is not available, Web menu cannot be opened

Page 51

 

 

Troubleshooting

 

 

Q2: Web menu setting is not available

 

 

 

 

Problem

Cause

Remedy

The web menu cannot be opened.

The network setting of the PC is

Set the LAN board and LAN card again and

 

inappropriate (when other PCs and network

reboot the PC.

 

printers in the LAN are also unusable).

 

 

Reset the IP address of the PC.

 

 

 

 

 

 

An inappropriate LAN cable is used for the

Use an optimum LAN cable (straight or cross

 

connection between this unit and the

cable).

 

network.

 

 

Use a LAN cable of Category 5 or higher.

 

 

 

 

 

 

This unit is malfunctioning.

Reset this unit to restore the factory settings

 

 

(page 32), and then perform desired settings.

 

 

 

 

An inappropriate URL is specified.

When using this unit for the first time or after

 

 

restoring the factory settings, access “http://

 

 

(IP address shown in the initial display of

 

 

this unit)”.

 

 

 

The web browser of the PC is set to use a proxy server.

The web menu cannot be opened when the proxy setting is inappropriate.

When using Internet Explorer 6 for Windows, open the “Tool” menu, select “Internet Options” → “Connection” tab → “Set LAN”, and then uncheck “Use proxy server”.

 

A network fault occurred or the

Consult your network administrator to have

 

communication is blocked by a firewall.

the network status checked.

 

 

 

The password for the web menu is

The password is incorrect (when a password

The password is case-sensitive. Be sure to

entered but it cannot be opened.

error is displayed).

enter alphanumeric characters correctly by

 

 

distinguishing the uppercase and lowercase

 

 

letters.

 

 

 

The settings are returned to the previous settings.

You did not click “Submit” or “Register” to confirm the settings.

After configuring the web menu settings, be sure to click “Submit” or “Register” to confirm the changed settings. If the window is closed without confirmation, the settings you made are not saved.

INFORMATION

ADDITIONAL

 

 

English

47

Page 50 Page 52
Image 51
Page 50 Page 52
Contents IP audio conference system Important Safty Instractions FCC Information for US customers Iii Contents Arrayed microphones and speakers for high audio quality FeaturesSettings from the PC Audio conference through networksSupplied Accessories About this manualAbout trademarks Top panel Controls and FunctionsAudio OUT terminal Right side panelDC in 12V terminal Audio in terminalArrayed speakers Bottom panel OtherSerial label Serial terminal192.168.100.200 Menu AddressDisplay LAN cable Preparation ProcedureTo configure the settings from a PC To use this unit with a SIP serverConnecting this unit Standby modeTo exit the standby mode and switch this unit on again To check if the correct network information is obtained Registering the network settings of this unitIf the IP address display is ???.???.???.??? Obtaining the IP address automaticallyIP ???.???.???.??? Menu Address Menu Settings Call History OnlineSettings Network Settings Sound Settings General Settings Network Settings IP Address Subnet Mask Default GatewayEnable Disable IP Adress 192.168.100.200Subnet Mask 255.255.255.000 Press or to select 4. DNS Server, Then press Default Gateway 000.000.000.000Press or to select 3. Default Gateway Then press DNS Server 000.000.000.000Installing this unit in the conference room About installation environmentTake the positions of the talkers in consideration 192.168.100.20 Menu Address CancelMaking a Call Calling another unit by specifying an IP address192.168.0.10 To make a call involving multiple LocationsTo mute the microphone Online 192.168.0.20 Calling another unit using the address bookAddress Book Headquarter Branch a Branch B Calling another unit in online statusPress or to select 2. Call History, Then press Online 192.168.0.20 CancelCalling another unit using the call history Call History Headquarter Branch aCall History Headquater Branch a CancelAnswering a Call To deny the callWhile having an incoming call, press To call another location during a call Carry out one of the following procedure during a callCarry out the procedure in Answering a Call Talking with Multiple Locations192.168.100.20 192.168.100.30 192.168.100.40 Menu Address When Speaker Mode is set to DivideWhen Speaker Mode is other than Divide 192.168.100.20 192.168.100.30 Menu AddressChange Location 192.168.100.20 192.168.100.30 Menu Address Press during callPress or to select 4. Change location Then press Configuring Settings Configuring settings using the keys on this unitPress or to select the menu category Then press Change the parameter Configuring settings using the web menuTo return to the previous menu without saving the setting To confirm the setting, pressSetting Menu List Configuring network settingsManaging address book information Configuring the SIP server setting Configuring the Dhcp server settingsConfiguring the connection mode Configuring the NAT traversal settingSelecting the audio pickup area Microphone mode Configuring sound settingsConfiguring the speaker mode Using the web menuConfiguring the room size Configuring the external input/output SettingConfiguring the audio connection function Configuring general settings Setting the password Restoring the factory settingsStoring the call history Registering a new address Editing Address BookEditing an existing address Deleting an address Click Submit Using the SIP ServerRegistering the SIP server information Web menu, click SIP ServerInitial display Display in SIP server operationTokyohq@sales.yama 2006.05 09 48 Menu Address Calling another unit by dialing the userWeb menu, click Sntp Server Setting Date and TimeContents of call history file Managing the Call HistoryViewing the call history file Confirming the System Log Message of This Unit syslog Web menu, click Syslog SettingMaximum number of locations by Cascade connection What is cascade connection ?Configure the setting of the cascade server Configure the settings Cascade clientsDisplay in cascade connection Software Licensing Agreement Updating the FirmwareWhen the firmware update is complete Settings General Settings Restore Settings Firmware UpdateFirmware Update ver. DT1.12-V1.6x Yes 2. No Firmware update process takes a few minutes to completeUpdating the firmware manually Press To cancel the firmware updateQ1 LED indicators do not light up TroubleshootingWeb menu cannot be opened Q2 Web menu setting is not availableCall cannot be originated Q3 Call is impossibleAudio is interrupted Q4 Other problemsTo cancel resetting in the middle Resetting the UnitRestore Settings Yes 2. No Resetting using the keys on this unitResetting using the web menu Web menu, click Restore Factory SettingsClick Restore Factory Settings Click Save Obtaining the Setting Information for Support on this UnitObtaining the audio characteristic information Click Download Setting Information in the web menuSpecifications Page All rights reserved
Top Page Image Contents