Sipura Technology SPA-2000 manual

Page 31

Interdigit Short Timer3

Short timeout between entering digits when dialing. Range: 0 – 64 sec

3

Notes:

1.The Call Progress Tones and DTMF playback level are not affected by the <FXS Port Output Gain>.

2.The interdigit timer values are used as defaults when dialing. The Interdigit_Long_Timer is used after any one digit, if all valid matching sequences in the dial plan are incomplete as dialed. The Interdigit_Short_Timer is used after any one digit, if at least one matching sequence is complete as dialed, but more dialed digits would match other as yet incomplete sequences.

3.4.7.4.Vertical Service Code Assignment

Parameter Name

Description

Default

 

Call Return Code

Call the last caller.

*69

 

Blind Transfer Code

Blind transfer current call to the target specified after

*98

 

 

the activation code

 

 

Cfwd All Act Code

Forward all calls to the target specified after the

*72

 

 

activation code

 

 

Cfwd All Deact Code

Cancel call forward all

*73

 

Cfwd Busy Act Code

Forward busy calls to the target specified after the

*90

 

 

activation code

 

 

Cfwd Busy Deact Code

Cancel call forward busy

*91

 

Cfwd No Ans Act Code

Forward no-answer calls to the target specified after

*92

 

 

the activation code

 

 

Cfwd No Ans Deact Code

Cancel call forward no-answer

*93

 

Cfwd Last Act Code

Forward the last inbound or outbound calls to the target

*63

 

 

specified after the activation code

 

 

Cfwd Last Deact Code

Cancel call forward last

*83

 

Block Last Act Code

Block the last inbound call

*60

 

Block Last Deact Code

Cancel blocking of the last inbound call

*80

 

Accept Last Act Code

Accept the last outbound call. Let it ring through when

*64

 

 

DND or Call Forward All is in effect

 

 

Accept Last Deact Code

Cancel Accept Last

*84

 

Call Back Act Code

Callback when the last outbound call is not busy

*66

 

Call Back Deact Code

Cancel callback

*86

 

CW_Act_Code

Enable Call Waiting on all calls

*56

 

CW_Deact_Code

Disable Call Waiting on all calls

*57

 

CW_Per_Call_Act_Code

Enable Call Waiting for the next call

*71

 

CW_Per_Call_Deact_Code

Disable Call Waiting for the next call

*70

 

Block_CID_Act_Code

Block CID on all outbound calls

*67

 

Block_CID_Deact_Code

Unblock CID on all outbound calls

*66

 

Block_CID_Per_Call_Act_Code

Block CID on the next outbound call

*81

 

Blcok_CID_Per_Call_Deact_Co

Unblock CID on the next inbound call

*82

 

de

 

 

 

Block_ANC_Act_Code

Block all anonymous calls

*77

 

Block_ANC_Deact_Code

Unblock all anonymous calls

*87

 

DND_Act_Code

Enable Do Not Disturb

*78

 

DND_Deact_Code

Disable Do Not Disturb

*79

 

CID_Act_Code

Enable Caller-ID Generation

*65

 

CID_Deact_Code

Disable Call-ID Generation

*85

 

CWCID_Act_Code

Enable Call Waiting Caller-ID generation

*25

 

CWCID_Deact_Code

Disable Call Waiting Caller-ID generation

*45

 

 

 

 

 

© 2003 Sipura Technology, Inc

Proprietary (See Copyright Notice on Page 2)

31

 

Image 31
Contents December Sipura Technology, IncUse of Proprietary Information and Copyright Notice Disclaimer Please ReadSipura Technology, Inc SPA-2000 User Guide Table of ContentsSPA-2000 Hardware Overview Product DescriptionStatus LED Description Default Handset Blink Behavior RateStatus Description Firmware Upgrade via Tftp Installation OverviewSoftware Configuration Firmware UpgradeIVR Interface Firmware Upgrade via PC Utility ProgramIVR Conventions 100 SPA-2000 Interactive Voice Response IVR MenuExample IVR Action IVR Menu Choice Parameters111 Requires Password101 110SPA Web Interface Administration PrivilegesWeb Interface Conventions Basic and Advanced Views SPA-2000 Information Web Page Advanced Admin View SPA-2000 Web Page Configuration Default ValuesSPA-2000 System Configuration Web Page Advanced Admin View SPA-2000 SIP Configuration Web Page Advanced Admin View Sipura Technology, Inc Proprietary See Copyright Notice on SPA-2000 Regional Configuration Web Page Advanced Admin View SPA-2000 Line 1 Configuration Web Page Line 2 Is Identical SPA-2000 User 1 Configuration Web Page User 2 Is Identical System Parameters Configuration ParametersProvisioning Parameters Protocol Parameters Upgrade ParametersSIP T1 NAT Support Parameter Name Description Default SDP Audio Codec Names Parameter Name Description DefaultLine 1 and Line 2 Parameters User Account Information Parameter Name Description DefaultSupplementary Services Enable Audio Settings Parameter Name Description Default Polarity Settings Parameter Name Description Default Dial Plan Parameter Name Description DefaultUser 1 and User 2 Parameters Speed Dial Settings Parameter Name Description Default Regional Parameters Call Progress Tones Parameter Name Description DefaultRing and CWT Cadence Parameter Name Description Default Control Timer Values sec Parameter Name Description Default Page Line 1/2 Status Miscellaneous Parameters Parameter Name Description DefaultCall Statistics Reporting System StatusCall 1/2 Status User GuidelinesReceiving a Phone Call Basic ServicesEnhanced Services Originating a Phone CallCalling Line Identification Presentation Clip To block Caller ID on all outbound calls, do Call WaitingFollowing Disable or Cancel Call Waiting Voice Mail Call-Waiting with Caller IDUnattended or Blind Call Transfer Attendant Call TransferThree-Way Calling Call HoldCall Return Three-Way Ad-Hoc Conference CallingCall FWD Unconditional Automatic Call BackCall FWD Busy Call FWD No Answer Distinctive / Priority Ringing and Call Waiting Tone Anonymous Call BlockingSpeed Calling Up to Eight 8 Numbers or IP Addresses Sipura Technology, Inc Proprietary See Copyright Notice on Where to Get Support Dial Plan Appendix I Dial Plan AdministrationPage Xxx 4911 1 2-9xx