Sipura Technology SPA-2000 manual Status LED Description, Status Description

Page 5

This LED indicates status via the following behaviors:

ON – LED remains solid on

OFF – LED remains solid off

LONG (Long On) – 3.0s on, 1s off continuously

FAST – 0.125s on, 0.125s off continuously

SLOW – 0.5s on, 0.5s off continuously

VSLO (Very Slow) – 1.0s on, 1.0s off continuously

HB (Heart Beat) – 0.125s on, 0.125s off, 0.125s on, 1s off continuously

3.One Ethernet 10baseT RJ-45 Jack Interface ( Figure , above):

This interface accepts a standard or crossover Ethernet cable with standard RJ-45 connector. For optimum performance, Sipura Technology recommends that a Category 5 cable or greater be used in conjunction with the SPA-2000.

4.One LED for Data Link and Activity ( Figure , above):

This LED indicates status via the following behaviors: ON – LED remains solid on

OFF – LED remains solid off

FAST – 0.125s on, 0.125s off continuously SLOW – 0.5s on, 0.5s off continuously

Variable Blink – LED blinks according to packet traffic activity

5.One 5 Volt Power Adapter Interface (

Figure , above)

This interface accepts the SPA-2000 power adapter that came with the unit. Sipura Technology does not support the use of any other power adapters other then the power adapter that was shipped with the SPA-2000 unit.

1.1.1. Status LED Description:

The SPA-2000 Status LED is used to indicate the current operation status of the SPA unit. The state is represented by a special blinking pattern of the Status LED (next to the RJ-11 ports on the right side of the device). The below table describes the various modes and behaviors of the SPA-2000 in relation to the Status LED and the handset behavior.

Status Description

 

LED

Default Handset

 

 

 

Blink

Behavior

 

 

 

Rate

 

 

Normal Operation – Both Lines on hook

OFF

Normal

 

Normal Operation – Either line off hook

ON

Normal

 

Downloading new firmware

 

SLOW

Silent

 

Writing firmware to flash

 

FAST

Silent

 

Looking for DHCP Server

 

SLOW

Silent

 

No DHCP Server

 

SLOW

Silent

 

IP Address Conflict

 

SLOW

Silent

 

 

 

 

 

 

© 2003 Sipura Technology, Inc

Proprietary (See Copyright Notice on Page 2)

5

Image 5
Contents December Sipura Technology, IncUse of Proprietary Information and Copyright Notice Disclaimer Please ReadSipura Technology, Inc SPA-2000 User Guide Table of ContentsSPA-2000 Hardware Overview Product DescriptionStatus Description Default Handset Blink Behavior RateStatus LED Description Software Configuration Installation OverviewFirmware Upgrade Firmware Upgrade via TftpIVR Conventions Firmware Upgrade via PC Utility ProgramIVR Interface Example SPA-2000 Interactive Voice Response IVR MenuIVR Action IVR Menu Choice Parameters 100101 Requires Password110 111Web Interface Conventions Administration PrivilegesSPA Web Interface Basic and Advanced Views SPA-2000 Information Web Page Advanced Admin View SPA-2000 Web Page Configuration Default ValuesSPA-2000 System Configuration Web Page Advanced Admin View SPA-2000 SIP Configuration Web Page Advanced Admin View Sipura Technology, Inc Proprietary See Copyright Notice on SPA-2000 Regional Configuration Web Page Advanced Admin View SPA-2000 Line 1 Configuration Web Page Line 2 Is Identical SPA-2000 User 1 Configuration Web Page User 2 Is Identical Provisioning Parameters Configuration ParametersSystem Parameters Protocol Parameters Upgrade ParametersSIP T1 NAT Support Parameter Name Description Default SDP Audio Codec Names Parameter Name Description DefaultLine 1 and Line 2 Parameters User Account Information Parameter Name Description DefaultSupplementary Services Enable Audio Settings Parameter Name Description Default User 1 and User 2 Parameters Dial Plan Parameter Name Description DefaultPolarity Settings Parameter Name Description Default Speed Dial Settings Parameter Name Description Default Regional Parameters Call Progress Tones Parameter Name Description DefaultRing and CWT Cadence Parameter Name Description Default Control Timer Values sec Parameter Name Description Default Page Call Statistics Reporting Miscellaneous Parameters Parameter Name Description DefaultSystem Status Line 1/2 StatusCall 1/2 Status User GuidelinesEnhanced Services Basic ServicesOriginating a Phone Call Receiving a Phone CallCalling Line Identification Presentation Clip Following Call WaitingTo block Caller ID on all outbound calls, do Disable or Cancel Call Waiting Voice Mail Call-Waiting with Caller IDUnattended or Blind Call Transfer Attendant Call TransferThree-Way Calling Call HoldCall Return Three-Way Ad-Hoc Conference CallingCall FWD Unconditional Automatic Call BackCall FWD Busy Call FWD No Answer Distinctive / Priority Ringing and Call Waiting Tone Anonymous Call BlockingSpeed Calling Up to Eight 8 Numbers or IP Addresses Sipura Technology, Inc Proprietary See Copyright Notice on Where to Get Support Dial Plan Appendix I Dial Plan AdministrationPage Xxx 4911 1 2-9xx