Peavey operation manual Peavey Impulse 1015P

Page 24

Peavey Impulse® 1015P

SPECIFICATIONS

Enclosure:

Peavey Impulse 1015P (domestic)

Frequency response: 56 Hz to 18 kHz

Low frequency limit (-3 dB point): 56 Hz

Useable low frequency limit (-10 dB point): 48 Hz

Internal Power Amplifiers (@120 VAC line): Woofer:

800 Watts peak dynamic power

400 Watts at clipping Tweeter:

200 Watts peak dynamic power

100 Watts at clipping

Nominal sensitivity (1W @1M, swept sine input in anechoic environment):

100 dB

Maximum sound pressure level @ 1 meter: 130 dB music peak

Nominal radiation angle:

90˚ horizontal by 45˚ vertical

Transducer compliment:

Model 1508-4 SPS 15" BWX Black Widow® weather-resistant woofer and RX22 2" titanium diaphragm compression driver tweeter

Box tuning frequency (Fbox): 54 Hz

Electroacoustic crossover frequency: 1600 Hz

Crossover type:

Internal electronic two-way crossover with CD horn EQ, level matching, active bass boost and subsonic filtering. The unit’s horn is spatially aligned with the woofer, so there is no need for phase alignment or time delay of the signals.

Crossover slopes:

18 dB/octave (third order) low pass,

18 dB/octave (third order) high pass, both with staggered poles and driver EQ

Electronic input impedance (nominal): 10 k Ohms unbalanced, 20 k Ohms balanced

Input connections:

One combo female XLR and 1/4" phone jack and one male XLR providing balanced operation in parallel. Also has a 1/4" phone jack-based Loop-Thru that allows other Impulse 1015P units to be linked to a single unit for signal source and volume control.

Contour switch:

Reduces mid-range by approximately 4 dB, from 300 Hz to 2 kHz.

Enclosure materials and finish: Injection-molded, high-impact polypropylene of a nominal thickness of 1/4" with internal ribbing and bracing, textured finish and a UL flame-rating. Molded material is black.

Mounting:

Flying via Peavey Versamount70 (top or bottom of cabinet), Peavey Array Brackets and four rubber feet for floor use. Also pole stand mount.

Dimensions:

28.562" (72.55 cm) tall by 21.312"

(54.13 cm) wide (11.5" {29.21 cm} wide in rear) by 17" (43.18 cm) deep

Optional accessories:

Impulse 1015 floor monitor kit

Net weight: 69 lbs.

Shipping weight: 72 lbs.

Additional remarks:

Also available as a passively crossed-over unit Impulse 1015.

ELECTRONICS AND AMPLIFIER

SPECIFICATIONS:

Electronic Input Impedance (Nominal): Primary balanced input: 10 k Ohms unbalanced, 20 k Ohms balanced

Loop thru input:

High Z

Infrasonic filter protection: 36 dB/octave roll-off

For both power amps:

Nominal Amplifier Frequency Response: +0, -1 dB from 10 Hz to 30 kHz

Hum and noise:

Greater than 90 dB below rated power.

DDTdynamic range:

Greater than 26 dB

THD and IM:

Typically less than 0.1 %

Woofer power amp: Damping Factor:

Greater than 100 @ 1,000 Hz, 4 Ohms.

Power requirements of Impulse 1015P System (domestic):

660 Watts maximum, 180 Watts nominal,

120 VAC, 60 Hz.

24

Image 24
Contents Page Page Important Safety Instructions Sound Level dBA, Slow ResponseEnglish IEC Power Cord Connection ON-OFF SwitchPower LED VolumeMIC on Switch Contour SwitchMIC Input LOOP-THRU JacksUsing the Impulse 1015P Flying the Impulse 1015P Getting AC Power to the Impulse 1015P Using the Impulse 1015P with a SubwooferGetting a Signal to the Impulse 1015P Volume Control AdjustmentUsing the MIC Input with Simultaneous Music Playback Troubleshooting ApplicationsHum or Buzz Care and Maintenance Description Architectural and Engineering Specifications Contour switch Electronics and Amplifier SpecificationsFor both power amps Enclosure Peavey Impulse 1015P domesticFrançais IntroductionConnecteur IEC Interrupteur ON-OFFLED D’ALIMENTATION ENTREES/SORTIES PrimairesInterrupteur Preampli Micro Entree MicrophoneInterrupteur DE Contour Jacks LOOP-THRUUtiliser L’IMPULSE 1015P Suspendre L’IMPULSE 1015P Alimenter Votre Impulse 1015PEnvoyer UN Signal a L’IMPULSE 1015P Reglage DU VolumeUtilisation Avec Subwoofer Trouver L’ORIGINE DE Problemes Courants Utilisation Avec D’AUTRES Impulse 1015PMaintenance Souffle et bourdonnementSon distordu Ingenieurie Amplitude Response 1m On-Axis Peavey Impulse 1015P Deutsch EinleitungPOWER-LED Rückseite ÜberlastschalterAnschluss DES IEC-NETZKABELS EIN/AUS-SCHALTERMIC-ON-SCHALTER CONTOUR-SCHALTERLOOP-THRU-KLINKEN BetriebsanleitungPage Senden VON Signalen AN DEN Impulse 1015P Versorgung DES Impulse 1015P MIT StromEinsatz DES Impulse 1015P MIT Einem Subwoofer Einstellen DES Lautstärkereglers Einsatz DES MIC-EINGANGS MIT Gleichzeitigem MUSIK-PLAYBACKEinsatz Mehrerer Impulse 1015P Oder anderer netzbetriebener Produkte der Impulse-SerieEinsatzbereiche FehlersuchePage Pflege UND Wartung Beschreibung Normal Contour 100 200 500 10k Peavey Impulse 1015P Español IntroducciónVolumen FusiblesInterruptor DE Encendido Y Apagado LED DE EncendidoInterruptor DE Encendido DEL Micrófono Entrada DE MicrófonoInterruptor DE Contorno Instrucciones DE USOUSO DEL Impulse 1015P Volando EL Impulse 1015P Ajuste DE Control DE Volumen Llevar Corriente Eléctrica AL Impulse 1015PUSO DEL Impulse 1015P CON UN Subwoofer Llevando Señal AL Impulse 1015PUSO DE LA Entrada DE Micro CON Música Simultanea USO DE Múltiples Impulse 1015POtros productos de la serie amplificada Impulse Problemas AplicacionesNo Hay Salida Cuidado Y Mantenimiento Descripción Especificaciones Arquitectónicas y de Ingeniería Peavey Impulse 1015P Page Page Page Peavey Electronics Corporation Limited Warranty 80305027