Peavey Impulse 1015P operation manual Using the MIC Input with Simultaneous Music Playback

Page 9

The amplifiers in the Impulse 1015P are equipped with DDT™ and an LED indicator to show it has engaged. If the sound seems heavily compressed and the DDT indicator is lighting more than occasionally, then the drive level from the mixer (or the Volume control on the Impulse 1015P) needs to be reduced.

When first turning on the sound system, switch-on all upstream electronics first, then the Impulse 1015P with its volume control fully counterclockwise (all the way down). Begin checking levels with the mixer output level controls all the way down, and bring them up slowly with the Impulse 1015P volume control set to the desired setting (halfway up recommended to start).

USING THE MIC INPUT WITH SIMULTANEOUS MUSIC PLAYBACK

With the mic input (8) switched on (7), a signal will be sent to the Impulse 1015P preamp electronics. Be sure to keep the mic away from the front of the speaker after switching the mic input ON and during level setting of the microphone, as very loud feedback will occur! The recommended placement of the person using the microphone is to the side and slightly to the rear of the Impulse 1015P, not out in front of the speaker system. When not using the mic input, be sure to switch off the mic (7) for the lowest noise and hum pickup.

Set the microphone level using the Volume control (6), the sound source may be louder during the actual presentation, and there is also the possibility that the microphone may be brought closer to the front of the speaker later on. For best results, the microphone should be held close to the user mouth instead of a foot or more away. Do not “eat” the mic that is, do not put your lips right on the mic, as this can often result in a boomy sound. The best results are obtained when the mic is approximately 2-3" away from the mouth.

When using the mic input (8) and the regular inputs (5) for simultaneous music, speech or singing, the volume for the mic should be set first using the Level control (6) as described above. The level fed to the regular inputs should be set to the desired level and matched to the microphone levels using the source Level Control or mixer.

USE OF MULTIPLE IMPULSE 1015Ps

(or other Impulse series powered products)

Multiple parallel inputs allow the Impulse 1015P to be “daisy-chained” from one to anther. Run the first cable from the mixer to the first Impulse 1015P, then hook a cable from its inputs to the second Impulse 1015P’s input. This can be continued for several units, depending on the length and total capacitance of the cables. With a low source impedance, such as a typical mixer output and typical balanced cables, two or three Impulse 1015Ps can be daisy-chained from one output using 30' or 40' cables without obvious loss of high frequencies.

The Loop-Thru jacks (10) can also be used to connect an Impulse 1015P or another Impulse series powered unit, and conveniently control volume from just one of the units. Connect a well-shielded 1/4" to 1/4" phone plug patch cord from the Loop Out jack of the unit with its input connected to the signal source, and then plug this cable into the other unit’s Loop In jack. The Volume control of the first unit now controls the volume for both identically.

Do not connect cables to the jacks while the units are ON and the Volume is turned up!

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Page Page Sound Level dBA, Slow Response Important Safety InstructionsEnglish ON-OFF Switch IEC Power Cord ConnectionPower LED VolumeContour Switch MIC on SwitchMIC Input LOOP-THRU JacksUsing the Impulse 1015P Flying the Impulse 1015P Using the Impulse 1015P with a Subwoofer Getting AC Power to the Impulse 1015PGetting a Signal to the Impulse 1015P Volume Control AdjustmentUsing the MIC Input with Simultaneous Music Playback Troubleshooting ApplicationsHum or Buzz Care and Maintenance Description Architectural and Engineering Specifications Electronics and Amplifier Specifications Contour switchFor both power amps Enclosure Peavey Impulse 1015P domesticIntroduction FrançaisInterrupteur ON-OFF Connecteur IECLED D’ALIMENTATION ENTREES/SORTIES PrimairesEntree Microphone Interrupteur Preampli MicroInterrupteur DE Contour Jacks LOOP-THRUAlimenter Votre Impulse 1015P Utiliser L’IMPULSE 1015P Suspendre L’IMPULSE 1015PEnvoyer UN Signal a L’IMPULSE 1015P Reglage DU VolumeUtilisation Avec Subwoofer Utilisation Avec D’AUTRES Impulse 1015P Trouver L’ORIGINE DE Problemes CourantsMaintenance Souffle et bourdonnementSon distordu Ingenieurie Amplitude Response 1m On-Axis Peavey Impulse 1015P Einleitung DeutschRückseite Überlastschalter POWER-LEDAnschluss DES IEC-NETZKABELS EIN/AUS-SCHALTERCONTOUR-SCHALTER MIC-ON-SCHALTERLOOP-THRU-KLINKEN BetriebsanleitungPage Senden VON Signalen AN DEN Impulse 1015P Versorgung DES Impulse 1015P MIT StromEinsatz DES Impulse 1015P MIT Einem Subwoofer Einsatz DES MIC-EINGANGS MIT Gleichzeitigem MUSIK-PLAYBACK Einstellen DES LautstärkereglersOder anderer netzbetriebener Produkte der Impulse-Serie Einsatz Mehrerer Impulse 1015PEinsatzbereiche FehlersuchePage Pflege UND Wartung Beschreibung Normal Contour 100 200 500 10k Peavey Impulse 1015P Introducción EspañolFusibles VolumenInterruptor DE Encendido Y Apagado LED DE EncendidoEntrada DE Micrófono Interruptor DE Encendido DEL MicrófonoInterruptor DE Contorno Instrucciones DE USOUSO DEL Impulse 1015P Volando EL Impulse 1015P Llevar Corriente Eléctrica AL Impulse 1015P Ajuste DE Control DE VolumenUSO DEL Impulse 1015P CON UN Subwoofer Llevando Señal AL Impulse 1015PUSO DE LA Entrada DE Micro CON Música Simultanea USO DE Múltiples Impulse 1015POtros productos de la serie amplificada Impulse Problemas AplicacionesNo Hay Salida Cuidado Y Mantenimiento Descripción Especificaciones Arquitectónicas y de Ingeniería Peavey Impulse 1015P Page Page Page Peavey Electronics Corporation Limited Warranty 80305027
Top Page Image Contents