Peavey Impulse 1015P operation manual MIC on Switch, MIC Input, Contour Switch, LOOP-THRU Jacks

Page 6

the mic level is set using this knob, and the ancillary signal (music into the In/Out jacks) level is then set using the source or feed (mixer).

(7) MIC ON SWITCH

When this switch is in the ON position, it connects the mic input jack (8) to the preamp circuitry. If the microphone is not in use, this switch should be in the OFF position to minimize noise or hum pickup from the mic input.

(8) MIC INPUT

Female XLR input jack for microphone use with the Impulse 1015P system. This connector provides +15 Volts phantom power and gain suitable to most of today’s “hot” microphones. When using this input in conjunction with the regular inputs (5), the volume for the mic should be set first using the Volume (6) control, and the level fed to the regular inputs should be set to the desired level using the source level control (mixer).

(9) CONTOUR SWITCH

When this switch is in the ON position, the mid-range is reduced by approximately 4 dB.

(10) LOOP-THRU JACKS

After the signal goes through the balanced inputs and the Volume control, these send the signal to another Impulse 1015P via its Loop In jack.

These are unbalanced high-Z jacks, so do not run the cable very far.

OPERATING INSTRUCTIONS

If it is necessary to remove the rear panel, or re-install it, then the bolts for the rear panel must be loosened or tightened by removing the front speaker grille, and then the woofer, and reaching in from the front to restrain the nuts from spinning. The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing to qualified service personnel.

The heat sink on the back plate can become hot to the touch. Do not block or cover the heat sink from ventilation.

Be sure to keep the microphone away from the front of the speaker after switching the mic input ON and while setting the microphone level, as very loud feedback will occur! Damage to the system is likely if this occurs!

DO NOT connect the inputs of the Impulse 1015P to the output of a power amplifier. The inputs are designed to be driven from a line-level strength signal.

DO NOT remove the protective metal grille.

DO NOT use the Input/Output jacks as mixers by trying to run more than one signal source at a time into them. The Input/Output jacks (5) are all hard-wired together to allow use of any of the connector types as an input, and to allow a further send or “daisy-chaining” of the input signal to some other audio device (such as another Impulse 1015P). Attempting to run two different signals directly into the Impulse 1015P could damage the outputs of the source units. Use a mixer to combine two or more signals into a single signal sent to the Impulse 1015P input.

6

Image 6
Contents Page Page Important Safety Instructions Sound Level dBA, Slow ResponseEnglish Power LED IEC Power Cord ConnectionON-OFF Switch VolumeMIC Input MIC on SwitchContour Switch LOOP-THRU JacksUsing the Impulse 1015P Flying the Impulse 1015P Getting a Signal to the Impulse 1015P Getting AC Power to the Impulse 1015PUsing the Impulse 1015P with a Subwoofer Volume Control AdjustmentUsing the MIC Input with Simultaneous Music Playback Troubleshooting ApplicationsHum or Buzz Care and Maintenance Description Architectural and Engineering Specifications For both power amps Contour switchElectronics and Amplifier Specifications Enclosure Peavey Impulse 1015P domesticFrançais IntroductionLED D’ALIMENTATION Connecteur IECInterrupteur ON-OFF ENTREES/SORTIES PrimairesInterrupteur DE Contour Interrupteur Preampli MicroEntree Microphone Jacks LOOP-THRUUtiliser L’IMPULSE 1015P Suspendre L’IMPULSE 1015P Alimenter Votre Impulse 1015PEnvoyer UN Signal a L’IMPULSE 1015P Reglage DU VolumeUtilisation Avec Subwoofer Trouver L’ORIGINE DE Problemes Courants Utilisation Avec D’AUTRES Impulse 1015PMaintenance Souffle et bourdonnementSon distordu Ingenieurie Amplitude Response 1m On-Axis Peavey Impulse 1015P Deutsch EinleitungAnschluss DES IEC-NETZKABELS POWER-LEDRückseite Überlastschalter EIN/AUS-SCHALTERLOOP-THRU-KLINKEN MIC-ON-SCHALTERCONTOUR-SCHALTER BetriebsanleitungPage Senden VON Signalen AN DEN Impulse 1015P Versorgung DES Impulse 1015P MIT StromEinsatz DES Impulse 1015P MIT Einem Subwoofer Einstellen DES Lautstärkereglers Einsatz DES MIC-EINGANGS MIT Gleichzeitigem MUSIK-PLAYBACKEinsatzbereiche Einsatz Mehrerer Impulse 1015POder anderer netzbetriebener Produkte der Impulse-Serie FehlersuchePage Pflege UND Wartung Beschreibung Normal Contour 100 200 500 10k Peavey Impulse 1015P Español IntroducciónInterruptor DE Encendido Y Apagado VolumenFusibles LED DE EncendidoInterruptor DE Contorno Interruptor DE Encendido DEL MicrófonoEntrada DE Micrófono Instrucciones DE USOUSO DEL Impulse 1015P Volando EL Impulse 1015P USO DEL Impulse 1015P CON UN Subwoofer Ajuste DE Control DE VolumenLlevar Corriente Eléctrica AL Impulse 1015P Llevando Señal AL Impulse 1015PUSO DE LA Entrada DE Micro CON Música Simultanea USO DE Múltiples Impulse 1015POtros productos de la serie amplificada Impulse Problemas AplicacionesNo Hay Salida Cuidado Y Mantenimiento Descripción Especificaciones Arquitectónicas y de Ingeniería Peavey Impulse 1015P Page Page Page Peavey Electronics Corporation Limited Warranty 80305027