Peavey Impulse 1015P Rear Panel Description Circuit Breaker, IEC Power Cord Connection, Power LED

Page 5

Rear Panel

REAR PANEL DESCRIPTION

(1) CIRCUIT BREAKER

The unit is AC power line circuit breaker- protected from overloads and fault conditions with a resettable 8 Amp breaker. In the rare event this unit should trip the breaker, turn the power switch to the OFF position, reset the breaker by pushing the center lever in all the way and reactivate the power switch. If the breaker lever does not stay in, it may need to cool first.

If the unit trips the breaker again and again, DO NOT continue to resetting the breaker, have the unit checked by a qualified service technician.

(2) IEC POWER CORD CONNECTION

The removable AC power cord plugs into this socket to supply AC line voltage to the power switch.

(3) ON-OFF SWITCH

This switch supplies AC power to the system electronics when switched to the ON position.

(4) POWER LED

Illuminates when the preamp electronics receive power, and should illuminate when the power switch is in the ON position and the AC power cord is connected and plugged into the wall outlet.

(5) PRIMARY INPUTS/OUTPUTS

The input and output jacks are in parallel to allow the audio input signal to be daisy-chained to other devices. The “input” level is the same as the “output” level and there is no isolation between the various jacks. Input jack (5a) is a medium impedence balanced combo female XLR and 1/4" RTS connector, while jack (5b) is a male XLR.

(6) VOLUME

This controls the gain (level) of the Impulse 1015P system. When used with the Primary Input /Output jacks (5), it directly sets the system output level. If the microphone input is utilized in conjunction with the Primary In/Out jacks, then

6

4

8

7

5

10

9

213

5

Image 5

Contents Page Page Sound Level dBA, Slow Response Important Safety InstructionsEnglish ON-OFF Switch IEC Power Cord ConnectionPower LED VolumeContour Switch MIC on SwitchMIC Input LOOP-THRU JacksUsing the Impulse 1015P Flying the Impulse 1015P Using the Impulse 1015P with a Subwoofer Getting AC Power to the Impulse 1015PGetting a Signal to the Impulse 1015P Volume Control AdjustmentUsing the MIC Input with Simultaneous Music Playback Hum or Buzz TroubleshootingApplications Care and Maintenance Description Architectural and Engineering Specifications Electronics and Amplifier Specifications Contour switchFor both power amps Enclosure Peavey Impulse 1015P domesticIntroduction FrançaisInterrupteur ON-OFF Connecteur IECLED D’ALIMENTATION ENTREES/SORTIES PrimairesEntree Microphone Interrupteur Preampli MicroInterrupteur DE Contour Jacks LOOP-THRUAlimenter Votre Impulse 1015P Utiliser L’IMPULSE 1015P Suspendre L’IMPULSE 1015PUtilisation Avec Subwoofer Envoyer UN Signal a L’IMPULSE 1015PReglage DU Volume Utilisation Avec D’AUTRES Impulse 1015P Trouver L’ORIGINE DE Problemes CourantsSon distordu MaintenanceSouffle et bourdonnement Ingenieurie Amplitude Response 1m On-Axis Peavey Impulse 1015P Einleitung DeutschRückseite Überlastschalter POWER-LEDAnschluss DES IEC-NETZKABELS EIN/AUS-SCHALTERCONTOUR-SCHALTER MIC-ON-SCHALTERLOOP-THRU-KLINKEN BetriebsanleitungPage Einsatz DES Impulse 1015P MIT Einem Subwoofer Senden VON Signalen AN DEN Impulse 1015PVersorgung DES Impulse 1015P MIT Strom Einsatz DES MIC-EINGANGS MIT Gleichzeitigem MUSIK-PLAYBACK Einstellen DES LautstärkereglersOder anderer netzbetriebener Produkte der Impulse-Serie Einsatz Mehrerer Impulse 1015PEinsatzbereiche FehlersuchePage Pflege UND Wartung Beschreibung Normal Contour 100 200 500 10k Peavey Impulse 1015P Introducción EspañolFusibles VolumenInterruptor DE Encendido Y Apagado LED DE EncendidoEntrada DE Micrófono Interruptor DE Encendido DEL MicrófonoInterruptor DE Contorno Instrucciones DE USOUSO DEL Impulse 1015P Volando EL Impulse 1015P Llevar Corriente Eléctrica AL Impulse 1015P Ajuste DE Control DE VolumenUSO DEL Impulse 1015P CON UN Subwoofer Llevando Señal AL Impulse 1015POtros productos de la serie amplificada Impulse USO DE LA Entrada DE Micro CON Música SimultaneaUSO DE Múltiples Impulse 1015P No Hay Salida ProblemasAplicaciones Cuidado Y Mantenimiento Descripción Especificaciones Arquitectónicas y de Ingeniería Peavey Impulse 1015P Page Page Page Peavey Electronics Corporation Limited Warranty 80305027