Peavey operation manual Using the Impulse 1015P Flying the Impulse 1015P

Page 7

WARNING: The Impulse 1015P is extremely efficient and powerful! This sound system can permanently damage hearing! Use extreme care setting the overall maximum loudness!

The apparent sound level of the Impulse 1015P can be deceiving due to its clear, clean sound output. The lack of distortion or obvious distress can make the sound level seem much lower than it actually is. This system is capable of SPLs in excess of 130 dB at 1 meter from the speaker!

USING THE IMPULSE 1015P

FLYING THE IMPULSE 1015P

Caution: Suspending or flying the Impulse 1015P must be done by a certified structural engineer.

Important Safety Information for Mounting the Peavey Impulse 1015P speaker systems.

Caution: Before attempting to suspend the Impulse 1015P, consult a certified structural engineer. This speaker can fall due to improper suspension, resulting in serious injury and property damage. Other enclosures must not be suspended below one, nor should additional weight be suspended from one of these units. Use only the correct mating hardware. All associated rigging is the responsibility of others.

Always use all four inserts of a given group as a set; NEVER use just one insert to fly a cabinet! The four insert groupings contain a top group of four and a bottom group of four, but some models also have a group of four on the rear plane of the cabinet.

Maximum enclosure angle from vertical hang: 30˚

Always loop a suitable safety chain or wire rope through the top handle of the unit and firmly attach to a suitable structural member as indicated by a certified structural engineer.

The recommended range of torque for the mounting bolt is 3 to 3-1/2 lb./ft. of torque. DO NOT OVERTIGHTEN! If an insert spins, it has been damaged and the cabinet cannot be flown!

Never transport the cabinet while it’s mounted on an array bracket or other mounting bracket, as this may unduly stress the mounting inserts.

WARNING! (note to structural engineer)

For the Impulse 1015P, the thread insertion depth of the end of the mounting bolt should not be more than 1/2" past the surface of the cabinet. If these thread insertion depths are exceeded, then the inserts may be damaged or unseated from the cabinet, severely compromising the mounting integrity of the cabinet!

The correct mounting bolt diameter and threads per inch are: 1/4" X 20. Use of a grade five bolt is recommended.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Page Page Sound Level dBA, Slow Response Important Safety InstructionsEnglish Volume IEC Power Cord ConnectionON-OFF Switch Power LEDLOOP-THRU Jacks MIC on SwitchContour Switch MIC InputUsing the Impulse 1015P Flying the Impulse 1015P Volume Control Adjustment Getting AC Power to the Impulse 1015PUsing the Impulse 1015P with a Subwoofer Getting a Signal to the Impulse 1015PUsing the MIC Input with Simultaneous Music Playback Applications TroubleshootingHum or Buzz Care and Maintenance Description Architectural and Engineering Specifications Enclosure Peavey Impulse 1015P domestic Contour switchElectronics and Amplifier Specifications For both power ampsIntroduction FrançaisENTREES/SORTIES Primaires Connecteur IECInterrupteur ON-OFF LED D’ALIMENTATIONJacks LOOP-THRU Interrupteur Preampli MicroEntree Microphone Interrupteur DE ContourAlimenter Votre Impulse 1015P Utiliser L’IMPULSE 1015P Suspendre L’IMPULSE 1015PReglage DU Volume Envoyer UN Signal a L’IMPULSE 1015PUtilisation Avec Subwoofer Utilisation Avec D’AUTRES Impulse 1015P Trouver L’ORIGINE DE Problemes CourantsSouffle et bourdonnement MaintenanceSon distordu Ingenieurie Amplitude Response 1m On-Axis Peavey Impulse 1015P Einleitung DeutschEIN/AUS-SCHALTER POWER-LEDRückseite Überlastschalter Anschluss DES IEC-NETZKABELSBetriebsanleitung MIC-ON-SCHALTERCONTOUR-SCHALTER LOOP-THRU-KLINKENPage Versorgung DES Impulse 1015P MIT Strom Senden VON Signalen AN DEN Impulse 1015PEinsatz DES Impulse 1015P MIT Einem Subwoofer Einsatz DES MIC-EINGANGS MIT Gleichzeitigem MUSIK-PLAYBACK Einstellen DES LautstärkereglersFehlersuche Einsatz Mehrerer Impulse 1015POder anderer netzbetriebener Produkte der Impulse-Serie EinsatzbereichePage Pflege UND Wartung Beschreibung Normal Contour 100 200 500 10k Peavey Impulse 1015P Introducción EspañolLED DE Encendido VolumenFusibles Interruptor DE Encendido Y ApagadoInstrucciones DE USO Interruptor DE Encendido DEL MicrófonoEntrada DE Micrófono Interruptor DE ContornoUSO DEL Impulse 1015P Volando EL Impulse 1015P Llevando Señal AL Impulse 1015P Ajuste DE Control DE VolumenLlevar Corriente Eléctrica AL Impulse 1015P USO DEL Impulse 1015P CON UN SubwooferUSO DE Múltiples Impulse 1015P USO DE LA Entrada DE Micro CON Música SimultaneaOtros productos de la serie amplificada Impulse Aplicaciones ProblemasNo Hay Salida Cuidado Y Mantenimiento Descripción Especificaciones Arquitectónicas y de Ingeniería Peavey Impulse 1015P Page Page Page Peavey Electronics Corporation Limited Warranty 80305027
Top Page Image Contents