Lincoln Electric IM916 manual LAYOUT-DIGITAL Display, POWER-UP Sequence, Changing Weld Modes

Page 23

b-5

OPERATION

b-5

 

 

 

LAYOUT-CONTROLS (SEE FIGURE b.3)

The MSP4 panel controls (Items 7 and 9) set consist of an encoder knob Item 8 and two push buttons. The encoder is primarily used to change the value of the selected attribute.

The left pushbutton (Item 7) is used to toggle between Weld Mode selection and any active Arc Controls (a.k.a. wave controls). The choices of wave controls varies by weld mode. For example, weld mode 31 has one wave control, “Pinch”. Weld mode 110 has three wave controls, “Peak Current”, “Background Current” and “Tailout”. If the selected weld mode has no wave controls, pressing the left pushbutton will have no effect. If the selected weld mode uses one or more wave controls, pressing the left pushbutton will sequence the selection from weld mode -> wave con- trol 1 (if active) -> wave control 2 (if active) -> wave control 3 (if active) -> wave control 4 (if active) then back to weld mode.

The right pushbutton (Item 9) is used to select attribut- es that affect the available weld parameters such as preflow time, burnback time, etc. Since most users will require infrequent access to these attributes, they are separate from weld mode selection and wave control adjustment.

LAYOUT-DIGITAL DISPLAY

The MSP4 display consists of a large 4-digit, 7-seg- ment LED display, two 8-character alphanumeric LED displays and one 16-character alphanumeric LED dis- play. The information shown on the various displays depends on the state of the user interface as described below.

When the MSP4 is being used to select a weld mode, the 4-digit display (Item 2) indicates the selected weld mode number. The upper 8-character alphanumeric display (Item 3) indicates the electrode type (steel, aluminum, etc.) The lower 8-character alphanumeric display (Item 4) indicates the electrode size (.035", 1/16", etc.).

The 16-character alphanumeric display (Item 5) indi- cates the process type and other information, the exact content of which depends on the selected weld mode. This additional information may include specific electrode type (e.g. 4043) and/or a description of the recommended gas (e.g. HeArCO2).

When the MSP4 is being used to change the value of an attribute, the 7-segment displays show the select- ed attribute’s value. The upper 8-character alphanu- meric display is typically not used while changing an attribute’s value. The lower 8-character alphanumeric display is used to indicate the units of the selected attribute (e.g. seconds, in/min, etc.). The 16-character alphanumeric display is used to display the name of the selected attribute.

The content of the displays while the user interface is being used for advance machine configuration (e.g. limit setting, pass code entering, machine setup, etc.) is described in later sections.

POWER-UP SEQUENCE

When power is first applied to the machine, a lamp test is performed. All discrete LED’s are turned on, all 7-segment displays will show a pattern of "8." and all alphanumeric displays will show a hatch pattern where every-other pixel is illuminated. The lamp test will last for two seconds, after which all displays are turned back off. The 16-character alphanumeric dis- play will show "Initializing…" while waiting for the Weld Sequencer to announce bus available. The MSP4 alphanumeric displays will then display the name of the weld table loaded in the power source while the user interface prepares the machine for operation. After all initialization is complete, the MSP4 will dis- play the weld mode information for the mode number that was selected when the machine was last pow- ered down.

CHANGING WELD MODES

To select a weld mode, press the left MSP4 pushbut- ton until the WELD MODE LED is illuminated. Turn the MSP4 encoder until the desired weld mode num- ber is displayed. As the MSP4 encoder knob is rotat- ed, only the weld mode number is displayed. After 1 second of encoder idle time, the user interface will change to the selected weld mode and the new mode’s electrode type, electrode size and process information will appear.

WELD MODE SEARCHING

The Weld Mode Search feature allows the selection of a welding mode based on certain criteria (wire size, process type, etc.).

SEARCHING FOR A WELD MODE

To search for a mode, turn the control knob until “Weld Mode Search” is displayed. This will appear in between the highest and the lowest weld mode num- bers.

O p w

D p a “b

R p s e

W P w p

E T m w

POWER FEED™ 10M DUAL WIRE FEEDER

Page 22 Page 24
Image 23
Page 22 Page 24
Contents IM916 Safety Depends on YouSafety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéOn-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyTAbLE of Contents Section F ViiSection D Section EAmp Rating Duty Cycle Power Feed 10M Dual Wire FeederWelding Capacity Rating Control CAbLE Connections Safety PrecautionControl CAbLE Specifications Electrode RoutingMinimum Copper Negative Electrode PolarityElectrode Sense Polarity TAbLE A.1CAC-C Voltage SensingElectrode Voltage Sensing Wire Drive Gear Ratio High or LOW SpeedSelecting the Proper Gear Ratio Work Voltage SensingTAbLE A.3 Changing the Wire Drive Gear RatioGear Ratio Change Procedure Gear Ratio RecognitionWith FAST-MATECONNECTION Wire Feed Drive Roll KitsProcedure to Install Drive Rolls and Wire Guides With Standard ConnectionGmaw Shielding GAS General GUN Connection GuidelinesWater Connections for Water Cooled Guns Wire Spindle PlacementWire Feed Shut Down Circuit Optional Flow Sensor Kit installation is as followsExAMPLES of Connecting AN Arclink Power Wave System Definitions of Welding Modes Safety PrecautionsRecommended Equipment Product DescriptionRecommended Processes and Equipment Recommended ProcessesVolt / Trim Meter Operational Features and ControlsPower FEED-10M Series System CONFIGURA- Tion Wire Feed Speed WFS / AMP MeterOverview Mode Select Panel 4 MSP4Dual Procedure / Dual Head Select W/MEMORY Panel Output ControlsLAYOUT-DIGITAL Display POWER-UP SequenceWeld Mode Searching Searching for a Weld ModeChanging ARC Wave Control Limit SettingMachine SETUP/USER Preferences Accessing the Machine Setup MenuParameter Definition SET-UP Features MenuUser Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change MethodTIG Gas Control Parameter Definition Gun Offset AdjustmentCrater Delay Reset Consumable WeightSense From Studs Arc Start/Loss Error TimeParameter Definition Push-Pull Gun Knob behavior Display Trim as Volts Option102 View Fatal Logs 100 View Diagnostics107 View Power Source Protocol Parameter Definition Show Test ModesParameter Definition 501 Encoder Lockout 503 Memory button Disable504 Mode Select Panel Lock 505 Setup Menu Lock509 UI Master Lockout Only be accessed using Power Wave Manager softwareParameter Definition 506 Set User Interface Passcode Figure B.4 Saving to Memory Dual Head / Dual Procedure with MemoryDual Procedure / Head Select MemoryStep / 4 Step Operation Cold FEED/GAS Purge Switch Electrode Polarity Wire Reel Loading READI-REELS, Spools or CoilsHOT Inch Foot AmptrolFigure b.1 GAS Guard Regulator Setting AdjustmentDrive Roll Pressure Setting Procedure for Setting Angle of FeedplateMaking a Weld Wire Reel ChangingWire Feed Overload Protection Status Light States Component Status LightsStatus Light States CON’T Attribute Limit SettingHigh Limit Low LimitRoll DH Drive 4-Driven Cored ElectrodeAluminum Electrode Optional Control Panel Kits K162-1 Wire Spindle AdapterField Installed OPTIONS/ACCESSORIES K1504-1 Coil AdapterGuns and GUN Adapters K435 Coil AdapterK363P READI-REEL Adapter K438 READI-REEL AdapterK1536-1 Water Flow Sensor KIT Dual Procedure Switch OptionsConduit Adapters K590-6 Water Connection KITK1555-2 Insulated Lift Hook K1733-1 Wire StraightenerK659-1 GAS Guard Regulator K1556-1 Light Duty Caster KITPeriodic Maintenance MaintenanceRoutine Maintenance TROUbLESHOOTING TROUbLESHOOTING Recommended PRObLEMS POSSIbLE CauseSymptoms Course of Action Field Service FacilityTROUbLESHOOTING Either of these fail, the problem is With switch open and closed. If it Err 005 Err 001Err 003 Err 004Err 201 Err 020Err 100 Err 200Three dashes Err 211Err 212 Err Error Codes for the Power WaveTROUbLESHOOTING Trol board OtherFeeder Power Feed 10M Dual WireDual Wire Feeder Power FeedL11044 DIAGRAMSF-4 Wire Drive Dimension Print Precaucion Warnung

IM916 specifications

Lincoln Electric IM916 is a state-of-the-art multi-process welding machine designed to meet the needs of professionals in various industries. This versatile welder combines productivity, performance, and durability, making it an ideal choice for both expert welders and apprentices alike.

One of the standout features of the Lincoln Electric IM916 is its multi-process capability. It supports MIG, TIG, and Stick welding, allowing users to switch between processes with ease. This adaptability ensures that users can tackle a diverse range of welding applications, from fabrication and repair work to manufacturing and construction projects.

The IM916 boasts advanced inverter technology, resulting in a compact design that does not compromise on power. Inverter technology allows for efficient energy consumption, providing a more stable arc with improved control and consistency. This feature not only enhances the quality of the welds but also prolongs the life of the machine and reduces operating costs.

Additionally, the machine is equipped with a digital display that offers real-time feedback on weld parameters, making it easier for users to adjust settings on the fly. This helps in achieving precise results and enhancing overall welding performance. The intuitive interface is user-friendly, making it suitable for beginners while still providing the advanced functionalities experienced welders require.

The Lincoln Electric IM916 also features a robust construction designed for longevity in harsh working environments. It is built to withstand the rigors of heavy use, with durable components and protective features that enhance its resilience. This reliability ensures that the machine can perform consistently, even in demanding conditions.

Furthermore, the IM916 is designed with portability in mind. Its lightweight design and integrated handles make it easy to transport between job sites. This mobility is crucial for professionals who require equipment that can keep up with a fast-paced work environment.

In terms of safety, the Lincoln Electric IM916 incorporates several protective features, including thermal overload protection and safety alerts. These mechanisms provide peace of mind to users, allowing them to focus on their work without worrying about equipment failure.

In summary, the Lincoln Electric IM916 is a highly versatile, efficient, and durable welding machine that stands out in its category. With its multi-process capabilities, advanced inverter technology, user-friendly interface, and durable construction, it caters to a wide range of welding tasks, making it a valuable asset for any welding professional.
Top Page Image Contents