Skil 2372 manual Safety Rules for Cordless Drill / Drivers

Page 4

SM 1619X03291 05-08 5/28/08 1:52 PM Page 4

Safety Rules for Cordless Drill / Drivers

Hold power tools by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool “live”

and shock the operator.

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may

lead to loss of control.

Do not drill, fasten or break into existing walls or other blind areas where electrical wiring may exist. If this situation is unavoidable, disconnect all fuses or circuit

breakers feeding this worksite.

Always hold the tool with both hands. If the bit jams two hands will give you maximum control over torque reaction or kickback.

Always wear safety goggles or eye protection when using this tool. Use a dust mask or respirator for applications which generate dust.

Secure the material being drilled. Never hold it in your hand or across legs. Unstable support can cause the drill bit to

bind causing loss of control and injury.

Disconnect battery pack from tool or place the switch in the locked or off position before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the

risk of starting the tool accidentally.

Position yourself to avoid being caught between the tool or side handle and walls or posts. Should the bit become bound or jammed in the work, the reaction torque of

the tool could crush your hand or leg.

If the bit becomes bound in the workpiece, release the trigger immediately, reverse the direction of rotation and slowly squeeze the trigger to back out the bit. Be ready for a strong reaction torque. The drill body will tend to

twist in the opposite direction as the drill bit is rotating.

Do not grasp the tool or place your hands too close to the spinning chuck or drill bit. Your hand may be lacerated.

When installing a bit, insert the shank of the bit well within the chuck. If the bit is not inserted deep enough, the grip of the

chuck over the bit is reduced and the loss of control is increased. After bit insertion, pull on bit to ensure it is locked.

Do not use dull or damaged bits and accessories. Dull or damaged bits have a greater tendency to bind in the workpiece.

When removing the bit from the tool avoid contact with skin and use proper protective gloves when grasping the bit or accessory. Accessories may be hot after prolonged use.

Check to see that keys and adjusting wrenches are removed from the drill before switching the tool "ON". Keys or wrenches can fly away at high velocity

striking you or a bystander.

Do not run the drill while carrying it at your side. A spinning drill bit could become entangled with clothing and injury may result.

! WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead-based paints,

Crystalline silica from bricks and cement and other masonry products, and

Arsenic and chromium from chemically- treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

-4-

Image 4
Contents Call Toll Free for For English Version Version françaiseSee Voir Ver la página General Safety Rules Work area safetyElectrical safety Personal safetyBattery tool use and care Power tool use and careService Safety Rules for Cordless Drill / Drivers Safety Rules for Cordless Power Wrenches Battery/ChargerBattery Care Connector PINCharging the Tool Tool with the charger connectedBattery Disposal Battery Removal InstructionsAttempting to remove battery from your tool Insulating tape to prevent shortingSymbols Functional Description and Specifications Cordless Drill/DriverInserting and Removing Accessories Operating InstructionsStall Protection FORWARD/REVERSING Lever & Trigger LockOperating Tips Fastening with Screws Drill BitsDrilling Wood Drilling MetalIntended USE Output DriveOutput Drive Socket BIT Holder Screwdriver Power Mode Trigger ON-OFF Switch Manual Mode AutolockFORWARD/REVERSING Lever Installing Fasteners FORWARD/REVERSING LeverAccessories MaintenanceCleaning Consignes générales de sécurité Sécurité du lieu de travailSécurité électrique Sécurité personnelleUtilisation et entretien des outils à piles Utilisation et entretien des outils ÉlectroportatifsEntretien Ne faites pas fonctionner la perceuse en la portant Consignes de sécurité pour perceuses/tournevis sans cordonLe plomb provenant des peintures à base de plomb Consignes de sécurité pour les boulonneuses sans fil Chargeur de pileEntretien des piles Charge DE LoutilBroche DU Connecteur Pas dans l’outil ou leMise au rebut des piles Ne tentez pas dePiles LITHIUM-ION Robert Bosch Tool Corporation participe volontairementSymboles Description fonctionnelle et spécifications Perceuse/visseuse sans filPrises Dair ChargeurConsignes de fonctionnement Embrayage Réglable FreinIndicateur DE Niveau DE Charge IndicateurFixation À L’AIDE DE VIS Fixation ’AIDE DE VISForets Perçage DU BoisInsertion ET Retrait Daccessoires Boulonneuse sans filNuméro de modèle Capacités maximalesMode Manuel Autolock Levier DE Mise EN Marche AVANT/MARCHE ArrièreEntretien AccessoiresNettoyage Normas generales de seguridad Seguridad del área de trabajoSeguridad eléctrica Seguridad personalUso y cuidado de las herramientas Alimentadas por baterías MecánicasServicio de ajustes y reparaciones SM 1619X03291 05-08 5/28/08 152 PM Batería/cargador No use casquillos desgastados o dañadosCuidado de las baterías Carga DE LA Batería DE LA HerramientaMarcha con el cargador conectado Pasador ConectorEliminación de las baterías Baterías DE Iones DE LitioFlecha a Flecha BCon aislamiento doble SímbolosDe Li-ion Descripción funcional y especificaciones Taladro/destornillador sin cordónLUZ LED Indicadora DE Comsutible Embrague AjustableInstrucciones de funcionamiento Inserción Y Remoción DE AccesoriosProtección Contra Paradas Palanca DE AVANCE/INVERSIÓN Cierre DEL GatilloConsejos de funcionamiento Sujecion CON Tornillos Brocas Para TaladroTaladrado DE Madera Taladrado DE MetalLlave de apriete eléctrica inalámbrica Accionador DE SalidaPalanca DE AVANCE/RETROCESO USO PrevistoModo Eléctrico Modo Manual AutolockMantenimiento AccesoriosServicio LimpiezaSM 1619X03291 05-08 5/28/08 152 PM