Hitachi ET 18DM instruction manual Insert the battery to the battery charger, Charging

Page 9

English

2.Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 2. Make sure it contacts the bottom of the battery charger.

3.Charging

Reading the Lamps

This charger is provided with a charging time lamp which displays estimated charging time, and a charging status lamp which displays the charging status.

(a)Charging Time Display

After beginning charging, the charging time lamp lights red with about 30 minutes remaining, lights orange with about 20 minutes remaining, and lights green with about five minutes remaining. When charging is complete, the charging status lamp lights green.

(b)High Temp Standby Display

Charging will not begin if the battery temperature is high. When this happens, the charging time of lamp flashes red (0.6 second cycle). Leave the battery in the charger, and charging will begin automatically when the temperature decreases.

(c)Charging Standby Display

Because the charger prioritizes power source output, charging is paused when the cordless tool switch is triggered during charging. When this happens, the charging time lamp will repeatedly flash (1 second cycle) in the current charging time display color (red/ orange/green). After the switch is released, charging automatically resumes in approximately one minute, and the lamp will light continuously.

(d)Unable to Charge Display

When the charger or the battery is malfunctioning, the charging status lamp flickers orange (0.2 second cycle). (See Table 2)

9

Image 9
Contents Model Modèle ET 18DM Modelo AvertissementContents Table DES MatieresÍndice Meanings of Signal Words Important Safety InformationSafety English Make Them Available to Other Users Owners of this Tool Disposal of the Exhausted BatteryOperation and Maintenance ModelName of Parts EB9S, EB12S Charging Insert the battery to the battery chargerTemperature is high Remove the battery from the battery charger Disconnect battery charger from the receptacleUsing the adapter ET18-18A DC Power Source MethodDisconnecting ConnectingDC Power Source Lamp High temperature protectionExcessive current protection Before USEService and Repairs Maintenance and InspectionStorage Check the ScrewsSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéSecurite Lire Tout CE Mode D’EMPLOITableau Français Mise AU Rebut D’UNE Batterie Usée Utilisation ET Entretien ModèleNOM DES Parties Utilisations SpecificationsMéthode DE Recharge Brancher la fiche du chargeur de batterie dans la priseRecharge Insérer la batterie dans le chargeur de batterieTableau 2 Indication des voyants Signification Retirer la batterie du chargeur de batterie Débrancher le chargeur de batterie de la priseMéthode DE Source D’ALIMENTATION CC Raccordement de l’adaptateur ET18-18AUtilisation de l’adaptateur ET18-18A Débranchement RaccordementVoyant de source d’alimentation CC Protection contre les températures élevéesProtection contre les courants excessifs Protection contre les longues utilisations continuesAvant L’UTILISATION Service APRES-VENTE ET RéparationsEntretien ET Inspection RangementSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadLEA Todas LAS Instrucciones SeguridadTabla Especificaciones Eliminación DE LAS Baterías Agotadas Operación Y Mantenimiento ModeloNomenclatura Aplicaciones EspecificacionesMétodo DE Carga Inserte el enchufe del cargador deCarga Inserte la batería en el cargador de bateríasLuz roja Iluminación Extraiga la batería del cargador de baterías Desconecte el cargador de baterías del tomacorrienteMétodo DE Fuente DE Alimentación DE CC Conexión del adaptador ET18-18AUso del adaptador ET18-18A Desconexión ConexiónLámpara de la fuente de alimentación de CC Protección contra altas temperaturasProtección contra corriente excesiva Mantenimiento E Inspección Antes DE LA UtilizaciónAlmacenamiento Servicio Y ReparaciónesHitachi Koki Canada Co