Hitachi CJ110MV instruction manual Assembly and Operation, Applications, Prior to Operation

Page 10

English

ASSEMBLY AND OPERATION

APPLICATIONS

Cutting various lumber and pocket cutting

Cutting mild steel plate, aluminum plate, and copper plate

Cutting plastics, such as phenol resin and vinyl chloride

Cutting thin and soft construction materials

Cutting stainless steel plate (With No. 97 blade)

PRIOR TO OPERATION

1.Power source

Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate.

2.Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury.

3.Extension cord

When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

WARNING:

Damaged cord must be replaced or repaired.

4.Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious hazard.

5.Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to prescribed precautions.

10

Image 10
Contents Avertissement AdvertenciaTable DES Matieres ContentsÍndice Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Never use a tool which is defective or operating abnormally Operate power tools at the rated voltageDo not wipe plastic parts with solvent Make Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Adjusting the orbital operation Adjusting the blade operating speedChanging blades Chip cover Sold separately Cutting stainless steel platesSplinter guard Sold separately Sub base Sold separatelySawing curved lines CuttingRectilinear cutting Cutting a circle or a circular arcPocket cutting Concerning Cutting of Stainless Steel PlatesCutting metallic materials Angular cuttingSelection of Blades Housing the Allen WrenchAdjust the speed Set the orbital position toConnecting with Cleaner Maintenance and Inspection List of appropriate blades Accessories Standard AccessoriesInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesUtiliser l’outil motorisé à la tension nominale Garder propres les évents d’air du moteurNe pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR NOM DES Parties Description FonctionnelleRemarque Avant L’UTILISATION Réglage de la vitesse de fonctionnement de la lame Remplacement des lamesPrecautions Réglage du fonctionnement orbitalCouvercle d’éclats Vendu séparément Découpage de plaques en acier inoxydableAnti-éclats Vendu séparément Socle auxiliaire Vendu séparémentAllumer la lampe PrecautionCoupe Coupe rectilinéaireDécoupe d’ouvertures Coupe d’un cercle ou d’un arc circulaireCoupe de matériaux métalliques Coupe angulairePour régler la vitesse AU Sujet DU Decoupage DE Plaques EN Acier InoxydableChoix DES Lames Régler la position orbitale surRangement DES Lames DE LA CLÉ Allen Raccordement AU NettoyeurEntretien ET Inspection Tableau Auminium,cuivre, lation Chassisen aluminiumAccessoires Accessoires StandardInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónAdvertencia Lea y entienda todas las instrucciones SeguridadSeguridad eléctrica Español Utilice la herramienta correcta Normas Y Símbolos Específicos DE SeguridadNo toque Nunca las piezas móviles Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeVoltios Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura NotaAplicaciones Montaje Y OperaciónAntes DE LA Operación Ajuste del funcionamiento orbital Cambio de las cuchillasAjustar la velocidad de operación de la cuchilla PrecaucionCubierta de virutas Vendido separadamente Corte de chapas de acero inoxidableProtector contra astillas Vendido separadamente Base secundaria Vendido separadamenteCorte para rectilinear CortarEncendido de la lámpara Serrar líneas curvasRecorte interior Cortar en circulo o un arco circularCortar materiales metálicos Corte angularAjuste la velocidad Sobre EL Corte DE Chapas DE Acero InoxidableSeleccion DE LAS Cuchillas Ajuste la posición orbital aAlojamiento DE LA Llave Allen Conexion CON EL LimpiadorMantenimiento E Inspección Madera útil GeneralAccesorios Accesorios EstándarEspañol ANº. îtem BNº. codigo CNº. usado DObservaciones Hitachi Koki Canada Co