Hitachi CJ110MV instruction manual Maintenance and Inspection

Page 17

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection.

1.Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one or resharpening without delay when abrasion is noted.

2.Inspecting the screws

Regularly inspect all screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately.

WARNING: Using this Jig Saw with loosen screws is extremely dangerous.

3.Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

4.Service and repairs

All quality power tools will eventually require servicing or replacement of parts because of wear from normal use. To assure that only authorized replacement parts will be used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.

5.Service parts list

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

17

Image 17

Contents Advertencia AvertissementÍndice ContentsTable DES Matieres Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Operate power tools at the rated voltageNever use a tool which is defective or operating abnormally Double Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Changing blades Adjusting the blade operating speedAdjusting the orbital operation Splinter guard Sold separately Cutting stainless steel platesChip cover Sold separately Sub base Sold separatelyRectilinear cutting CuttingSawing curved lines Cutting a circle or a circular arcCutting metallic materials Concerning Cutting of Stainless Steel PlatesPocket cutting Angular cuttingAdjust the speed Housing the Allen WrenchSelection of Blades Set the orbital position toConnecting with Cleaner Maintenance and Inspection List of appropriate blades Standard Accessories AccessoriesSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéAvertissement Lire et coxmprendre toutes les instructions SecuriteFrançais NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesNe pas essuyer les parties en plastique avec du solvant Garder propres les évents d’air du moteurUtiliser l’outil motorisé à la tension nominale Double Isolation Pour UN Fonctionnement Plus SUR Remarque Description FonctionnelleNOM DES Parties Avant L’UTILISATION Precautions Remplacement des lamesRéglage de la vitesse de fonctionnement de la lame Réglage du fonctionnement orbitalAnti-éclats Vendu séparément Découpage de plaques en acier inoxydableCouvercle d’éclats Vendu séparément Socle auxiliaire Vendu séparémentCoupe PrecautionAllumer la lampe Coupe rectilinéaireCoupe de matériaux métalliques Coupe d’un cercle ou d’un arc circulaireDécoupe d’ouvertures Coupe angulaireChoix DES Lames AU Sujet DU Decoupage DE Plaques EN Acier InoxydablePour régler la vitesse Régler la position orbitale surRaccordement AU Nettoyeur Rangement DES Lames DE LA CLÉ AllenEntretien ET Inspection Auminium,cuivre, lation Chassisen aluminium TableauAccessoires Standard AccessoiresSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad eléctrica SeguridadAdvertencia Lea y entienda todas las instrucciones Español No toque Nunca las piezas móviles Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje correctamente la herramientaNo limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricasVoltios Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nomenclatura Descripción FuncionalEspecificaciones NotaAntes DE LA Operación Montaje Y OperaciónAplicaciones Ajustar la velocidad de operación de la cuchilla Cambio de las cuchillasAjuste del funcionamiento orbital PrecaucionProtector contra astillas Vendido separadamente Corte de chapas de acero inoxidableCubierta de virutas Vendido separadamente Base secundaria Vendido separadamenteEncendido de la lámpara CortarCorte para rectilinear Serrar líneas curvasCortar materiales metálicos Cortar en circulo o un arco circularRecorte interior Corte angularSeleccion DE LAS Cuchillas Sobre EL Corte DE Chapas DE Acero InoxidableAjuste la velocidad Ajuste la posición orbital aConexion CON EL Limpiador Alojamiento DE LA Llave AllenMantenimiento E Inspección General Madera útilAccesorios Estándar AccesoriosEspañol ANº. îtem BNº. codigo CNº. usado DObservaciones Hitachi Koki Canada Co