Hitachi CJ110MV instruction manual Cutting stainless steel plates, Splinter guard Sold separately

Page 12

English

(2)For the hard material, such as a steel plate, etc., decrease the orbital operation. For the soft material, such as lumber, plastic, etc., increase the orbital operation to increase work efficiency. To cut the material accurately, decrease the orbital operation.

9.Cutting stainless steel plates

This Jig Saw can cut stainless steel plates by using No. 97 blade. Carefully read “Concerning cutting of stainless steel plates” for proper operation.

Change knob

Fig. 7

10.Splinter guard (Sold separately)

Using the splinter guard when cutting wood materials will reduce splintering of cut surfaces.

Insert the splinter guard in the space on the base, and push it completely. (see Fig. 8)

11.Chip cover (Sold separately)

Chip cover prevents chips from flying off and improves the efficiency of dust collector (Sold separately).

Insert the chip cover between the base and lever, and push with a slight pressure until it catches in place. (Fig. 9)

When removing chip cover, hold both sides of knob and slightly open until it can be removed from the Jig Saw.

NOTE: There is a possibility that chip cover is frosted when cutting the metal.

12.Sub base (Sold separately)

Using the sub base (made from steel) will reduce abrasion of aluminium base especially in cutting metals.

Using the sub base (made from resin) will reduce scratching of cut surface. Attach the sub base to the bottom surface of base by attached 4 screws.

13.Lighting up the lamp

CAUTION: Do not look in the light or see the

source of light directly. To turn on the lamp, pull the trigger. Release the trigger to turn off.

Splinter guard

Base

Fig. 8

Lever

Chip cover

Base

Fig. 9

12

Image 12

Contents Avertissement AdvertenciaContents Table DES MatieresÍndice Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Operate power tools at the rated voltage Never use a tool which is defective or operating abnormallyDo not wipe plastic parts with solvent Make Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationSpecifications Functional DescriptionName of Parts Assembly and Operation ApplicationsPrior to Operation Adjusting the blade operating speed Adjusting the orbital operationChanging blades Cutting stainless steel plates Splinter guard Sold separatelyChip cover Sold separately Sub base Sold separatelyCutting Rectilinear cuttingSawing curved lines Cutting a circle or a circular arcConcerning Cutting of Stainless Steel Plates Cutting metallic materialsPocket cutting Angular cuttingHousing the Allen Wrench Adjust the speedSelection of Blades Set the orbital position toConnecting with Cleaner Maintenance and Inspection List of appropriate blades Accessories Standard AccessoriesInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesGarder propres les évents d’air du moteur Utiliser l’outil motorisé à la tension nominaleNe pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesRemarque Avant L’UTILISATION Remplacement des lames PrecautionsRéglage de la vitesse de fonctionnement de la lame Réglage du fonctionnement orbitalDécoupage de plaques en acier inoxydable Anti-éclats Vendu séparémentCouvercle d’éclats Vendu séparément Socle auxiliaire Vendu séparémentPrecaution CoupeAllumer la lampe Coupe rectilinéaireCoupe d’un cercle ou d’un arc circulaire Coupe de matériaux métalliquesDécoupe d’ouvertures Coupe angulaireAU Sujet DU Decoupage DE Plaques EN Acier Inoxydable Choix DES LamesPour régler la vitesse Régler la position orbitale surRangement DES Lames DE LA CLÉ Allen Raccordement AU NettoyeurEntretien ET Inspection Tableau Auminium,cuivre, lation Chassisen aluminiumAccessoires Accessoires StandardInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad Advertencia Lea y entienda todas las instruccionesSeguridad eléctrica Español Normas Y Símbolos Específicos DE Seguridad No toque Nunca las piezas móvilesUtilice la herramienta correcta Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeVoltios Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones NotaMontaje Y Operación AplicacionesAntes DE LA Operación Cambio de las cuchillas Ajustar la velocidad de operación de la cuchillaAjuste del funcionamiento orbital PrecaucionCorte de chapas de acero inoxidable Protector contra astillas Vendido separadamenteCubierta de virutas Vendido separadamente Base secundaria Vendido separadamenteCortar Encendido de la lámparaCorte para rectilinear Serrar líneas curvasCortar en circulo o un arco circular Cortar materiales metálicosRecorte interior Corte angularSobre EL Corte DE Chapas DE Acero Inoxidable Seleccion DE LAS CuchillasAjuste la velocidad Ajuste la posición orbital aAlojamiento DE LA Llave Allen Conexion CON EL LimpiadorMantenimiento E Inspección Madera útil GeneralAccesorios Accesorios EstándarEspañol ANº. îtem BNº. codigo CNº. usado DObservaciones Hitachi Koki Canada Co