Hitachi CJ110MV Concerning Cutting of Stainless Steel Plates, Cutting metallic materials

Page 14

English

4. Cutting metallic materials

(1)Adjust the speed Dial between scales “3” and “4”.

(2)Set the orbital position to “0” or “I”.

(3)Always use an appropriate cutting fluid (spindle oil, soapy water, etc.). When a liquid cutting fluid is not avaiable, apply grease to the back surface of the material to be cut.

5.Pocket cutting

(1) In lumber

Aligning the blade direction with the grain of the wood, cut step by step until a window hole is cut in the center of the lumber. (Fig. 14)

(2) In other materials

When cutting a window hole in materials other than lumber, initially bore a hole with a drill or similar tool from which to start cutting.

6. Angular cutting

The base can be swiveled to both sides by up to 45° for angular cutting. (Fig. 15)

(1)Loosen the base bolt by allen wrench attached on base and move the base fully forward. (Fig. 10, 11)

(2)Align the scale (from 0 degrees to 45 degrees by 15-degree increments) of the semi-circular part of the base with the [] mark on the gear cover. (Fig. 16)

(3)Tighten the M5 bolt again. (Fig. 10)

(4)Set the orbital position to “0”.

NOTE: Angular cutting can not be done when adopting chip cover or dust collector.

Semi-circular part

Fig. 14

Base

Fig. 15

mark

Scale

Fig. 16

CONCERNING CUTTING OF STAINLESS STEEL PLATES

When used with the No. 97 blade, can cut stainless steel plates.

Note the following to adjus the unit.

CAUTION:

⬤In order to prevent blade dislodging, damage or excessive wear on the Plunger, please make sure to have surface of the base plate attached to the work piece while sawing.

14

Image 14

Contents Avertissement AdvertenciaÍndice ContentsTable DES Matieres Important Safety Information Meanings of Signal WordsSafety General Safety RulesEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Operate power tools at the rated voltageNever use a tool which is defective or operating abnormally Make Them Available to Other Users Owners of this Tool Double Insulation for Safer OperationName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Changing blades Adjusting the blade operating speedAdjusting the orbital operation Chip cover Sold separately Cutting stainless steel platesSplinter guard Sold separately Sub base Sold separatelySawing curved lines CuttingRectilinear cutting Cutting a circle or a circular arcPocket cutting Concerning Cutting of Stainless Steel PlatesCutting metallic materials Angular cuttingSelection of Blades Housing the Allen WrenchAdjust the speed Set the orbital position toConnecting with Cleaner Maintenance and Inspection List of appropriate blades Accessories Standard AccessoriesInformations Importantes DE Sécurité Signification DES Mots D’AVERTISSEMENTSecurite Avertissement Lire et coxmprendre toutes les instructionsFrançais Regles DE Securite Specifiques ET Symboles NE Jamais toucher les parties mobilesNe pas essuyer les parties en plastique avec du solvant Garder propres les évents d’air du moteurUtiliser l’outil motorisé à la tension nominale Double Isolation Pour UN Fonctionnement Plus SUR Remarque Description FonctionnelleNOM DES Parties Avant L’UTILISATION Réglage de la vitesse de fonctionnement de la lame Remplacement des lamesPrecautions Réglage du fonctionnement orbitalCouvercle d’éclats Vendu séparément Découpage de plaques en acier inoxydableAnti-éclats Vendu séparément Socle auxiliaire Vendu séparémentAllumer la lampe PrecautionCoupe Coupe rectilinéaireDécoupe d’ouvertures Coupe d’un cercle ou d’un arc circulaireCoupe de matériaux métalliques Coupe angulairePour régler la vitesse AU Sujet DU Decoupage DE Plaques EN Acier InoxydableChoix DES Lames Régler la position orbitale surRangement DES Lames DE LA CLÉ Allen Raccordement AU NettoyeurEntretien ET Inspection Tableau Auminium,cuivre, lation Chassisen aluminiumAccessoires Accessoires StandardInformación Importante Sobre Seguridad Significado DE LAS Palabras DE SeñalizaciónSeguridad eléctrica SeguridadAdvertencia Lea y entienda todas las instrucciones Español Utilice la herramienta correcta Normas Y Símbolos Específicos DE SeguridadNo toque Nunca las piezas móviles Maneje correctamente la herramientaManeje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeVoltios Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FuncionalNomenclatura NotaAntes DE LA Operación Montaje Y OperaciónAplicaciones Ajuste del funcionamiento orbital Cambio de las cuchillasAjustar la velocidad de operación de la cuchilla PrecaucionCubierta de virutas Vendido separadamente Corte de chapas de acero inoxidableProtector contra astillas Vendido separadamente Base secundaria Vendido separadamenteCorte para rectilinear CortarEncendido de la lámpara Serrar líneas curvasRecorte interior Cortar en circulo o un arco circularCortar materiales metálicos Corte angularAjuste la velocidad Sobre EL Corte DE Chapas DE Acero InoxidableSeleccion DE LAS Cuchillas Ajuste la posición orbital aAlojamiento DE LA Llave Allen Conexion CON EL LimpiadorMantenimiento E Inspección Madera útil GeneralAccesorios Accesorios EstándarEspañol ANº. îtem BNº. codigo CNº. usado DObservaciones Hitachi Koki Canada Co