Hitachi CJ110MV instruction manual Selection of Blades, Housing the Allen Wrench, Adjust the speed

Page 15

English

When cutting stainless steel plates, adjust the unit as described below:

1. Adjust the speed

	Blade	Thickness of material	Dial Scale
	No. 97	1/16" – 5/32" (1.5 mm – 2.5 mm)	Middle groove position
	No. 97	1/16" – 5/32" (1.5 mm – 2.5 mm)	between scales “2” and “3”
			between scales “2” and “3”

NOTE: Dial scale reading is for reference only. The higher the speed is, the quicker the material is cut. But the service life of the blade will be reduced in this case. When the speed is too low, cutting will take longer, although the service life will be prolonged. Make adjustments as desired.

2.Set the orbital position to “0”

NOTE: When cutting use cutting fluid (oil base cutting fluid) to prolong the blade’s service life.

SELECTION OF BLADES

◯Accessory blades

To ensure maximum operating efficiency and results, it is very important to select the appropriate blade best suited to the type and thickness of the material to be cut. Three types of blades are provided as standard accessories. The blade number is engraved in the vicinity of the mounting portion of each blade. Select appropriate blades by referring to Table 1 (page 18).

HOUSING THE ALLEN WRENCH

◯ It is possible to house the axiliary allen wrench	I	Allen
◯ It is possible to house the axiliary allen wrench		Allen
on the base (see Fig. 17).		wrench
	II
	Base
	Fig. 17

15

Image 15

Contents Advertencia AvertissementContents Table DES MatieresÍndice Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Operate power tools at the rated voltage Never use a tool which is defective or operating abnormallyDo not wipe plastic parts with solvent Double Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolSpecifications Functional DescriptionName of Parts Assembly and Operation ApplicationsPrior to Operation Adjusting the blade operating speed Adjusting the orbital operationChanging blades Sub base Sold separately Cutting stainless steel platesSplinter guard Sold separately Chip cover Sold separatelyCutting a circle or a circular arc CuttingRectilinear cutting Sawing curved linesAngular cutting Concerning Cutting of Stainless Steel PlatesCutting metallic materials Pocket cuttingSet the orbital position to Housing the Allen WrenchAdjust the speed Selection of BladesConnecting with Cleaner Maintenance and Inspection List of appropriate blades Standard Accessories AccessoriesSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéAvertissement Lire et coxmprendre toutes les instructions SecuriteFrançais NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesGarder propres les évents d’air du moteur Utiliser l’outil motorisé à la tension nominaleNe pas essuyer les parties en plastique avec du solvant Double Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesRemarque Avant L’UTILISATION Réglage du fonctionnement orbital Remplacement des lamesPrecautions Réglage de la vitesse de fonctionnement de la lameSocle auxiliaire Vendu séparément Découpage de plaques en acier inoxydableAnti-éclats Vendu séparément Couvercle d’éclats Vendu séparémentCoupe rectilinéaire PrecautionCoupe Allumer la lampeCoupe angulaire Coupe d’un cercle ou d’un arc circulaireCoupe de matériaux métalliques Découpe d’ouverturesRégler la position orbitale sur AU Sujet DU Decoupage DE Plaques EN Acier InoxydableChoix DES Lames Pour régler la vitesseRaccordement AU Nettoyeur Rangement DES Lames DE LA CLÉ AllenEntretien ET Inspection Auminium,cuivre, lation Chassisen aluminium TableauAccessoires Standard AccessoiresSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad Advertencia Lea y entienda todas las instruccionesSeguridad eléctrica Español Maneje correctamente la herramienta Normas Y Símbolos Específicos DE SeguridadNo toque Nunca las piezas móviles Utilice la herramienta correctaNo limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricasVoltios Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nota Descripción FuncionalNomenclatura EspecificacionesMontaje Y Operación AplicacionesAntes DE LA Operación Precaucion Cambio de las cuchillasAjustar la velocidad de operación de la cuchilla Ajuste del funcionamiento orbitalBase secundaria Vendido separadamente Corte de chapas de acero inoxidableProtector contra astillas Vendido separadamente Cubierta de virutas Vendido separadamenteSerrar líneas curvas CortarEncendido de la lámpara Corte para rectilinearCorte angular Cortar en circulo o un arco circularCortar materiales metálicos Recorte interiorAjuste la posición orbital a Sobre EL Corte DE Chapas DE Acero InoxidableSeleccion DE LAS Cuchillas Ajuste la velocidadConexion CON EL Limpiador Alojamiento DE LA Llave AllenMantenimiento E Inspección General Madera útilAccesorios Estándar AccesoriosEspañol ANº. îtem BNº. codigo CNº. usado DObservaciones Hitachi Koki Canada Co