Hitachi CJ110MV instruction manual Changing blades, Adjusting the blade operating speed

Page 11

6. Changing blades

(1)Open the lever up to the stop. (Fig. 3-I)

(2)Remove fitted blade

(3)Insert new blade up to the stop in the balde holder. (Fig. 3-II)

(4)Close the lever. (Fig. 3-III)

CAUTION:

◯Be sure to switch power OFF and disconnect the plug from the receptacle when changing blades.

◯Do not open the lever when plunger is moving.

NOTE:

◯Confirm the protrusions of blade inserted to the blade holder surely. (Fig. 4)

◯Confirm the blade located between the groove of roller. (Fig. 5)

7.Adjusting the blade operating speed

The jig saw is equipped with the electric control circuit which enables stepless speed control. To adjust the speed, turn the dial shown in Fig. 6. When the dial is set to “1”, the jig saw operates at the minimum speed (850 /min.). When the dial set to “5”, the jig saw operates at the maximum speed (3000/min.). Adjust the speed according to the material to be cut and working efficiency.

CAUTION:

⬤At low speed (dial setting: 1 or 2) do not cut a wood with a thickness of more than 3/8" (10 mm) or metal with a thickness of more than 1/32" (1 mm).

8. Adjusting the orbital operation

(1)This Jig Saw employs orbital operation which moves the blade back and forth, as well as up and down. Set the change knob shown in Fig. 7 to “0” to eliminate the orbital operation (the blade moves only up and down). The orbital operation can be selected in 4 steps from “0” to “III”.

English

Blade

Blade holder

Lever

Fig. 3

Blade

Blade holder

Fig. 4

BladeBlade

Roller Roller

Fig. 5

Dial

Fig. 6

11

Image 11

Contents Advertencia AvertissementÍndice ContentsTable DES Matieres Meanings of Signal Words Important Safety InformationGeneral Safety Rules SafetyEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Operate power tools at the rated voltageNever use a tool which is defective or operating abnormally Double Insulation for Safer Operation Make Them Available to Other Users Owners of this ToolName of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Changing blades Adjusting the blade operating speedAdjusting the orbital operation Sub base Sold separately Cutting stainless steel platesSplinter guard Sold separately Chip cover Sold separatelyCutting a circle or a circular arc CuttingRectilinear cutting Sawing curved linesAngular cutting Concerning Cutting of Stainless Steel PlatesCutting metallic materials Pocket cuttingSet the orbital position to Housing the Allen WrenchAdjust the speed Selection of BladesConnecting with Cleaner Maintenance and Inspection List of appropriate blades Standard Accessories AccessoriesSignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéAvertissement Lire et coxmprendre toutes les instructions SecuriteFrançais NE Jamais toucher les parties mobiles Regles DE Securite Specifiques ET SymbolesNe pas essuyer les parties en plastique avec du solvant Garder propres les évents d’air du moteurUtiliser l’outil motorisé à la tension nominale Double Isolation Pour UN Fonctionnement Plus SUR Remarque Description FonctionnelleNOM DES Parties Avant L’UTILISATION Réglage du fonctionnement orbital Remplacement des lamesPrecautions Réglage de la vitesse de fonctionnement de la lameSocle auxiliaire Vendu séparément Découpage de plaques en acier inoxydableAnti-éclats Vendu séparément Couvercle d’éclats Vendu séparémentCoupe rectilinéaire PrecautionCoupe Allumer la lampeCoupe angulaire Coupe d’un cercle ou d’un arc circulaireCoupe de matériaux métalliques Découpe d’ouverturesRégler la position orbitale sur AU Sujet DU Decoupage DE Plaques EN Acier InoxydableChoix DES Lames Pour régler la vitesseRaccordement AU Nettoyeur Rangement DES Lames DE LA CLÉ AllenEntretien ET Inspection Auminium,cuivre, lation Chassisen aluminium TableauAccessoires Standard AccessoiresSignificado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad eléctrica SeguridadAdvertencia Lea y entienda todas las instrucciones Español Maneje correctamente la herramienta Normas Y Símbolos Específicos DE SeguridadNo toque Nunca las piezas móviles Utilice la herramienta correctaNo limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricasVoltios Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Nota Descripción FuncionalNomenclatura EspecificacionesAntes DE LA Operación Montaje Y OperaciónAplicaciones Precaucion Cambio de las cuchillasAjustar la velocidad de operación de la cuchilla Ajuste del funcionamiento orbitalBase secundaria Vendido separadamente Corte de chapas de acero inoxidableProtector contra astillas Vendido separadamente Cubierta de virutas Vendido separadamenteSerrar líneas curvas CortarEncendido de la lámpara Corte para rectilinearCorte angular Cortar en circulo o un arco circularCortar materiales metálicos Recorte interiorAjuste la posición orbital a Sobre EL Corte DE Chapas DE Acero InoxidableSeleccion DE LAS Cuchillas Ajuste la velocidadConexion CON EL Limpiador Alojamiento DE LA Llave AllenMantenimiento E Inspección General Madera útilAccesorios Estándar AccesoriosEspañol ANº. îtem BNº. codigo CNº. usado DObservaciones Hitachi Koki Canada Co