DeWalt D55695 Preparation For Use Pre-Start Checklist Fig, Initial Set-up Fig, Lifting, Moving

Page 18

English

CAUTION: Risk of property damage. The wheels and handle do not provide adequate clearance, stability or support for pulling the unit up and down stairs or steps. The unit must be lifted, or pushed up a ramp.

When

transporting

the

 

 

compressor

 

in

a

vehicle,

r, s

 

trailer, etc. ensure that the air

R, S

tank is drained and the unit is

 

secured and placed on a flat

 

 

horizontal

surface.

NOTE:

 

 

Use recommended tie down

 

 

points (R) when transporting.

R

T

Use care when driving so to

 

 

avoid tipping the unit over in

 

 

the

vehicle.

Damage

can

r, S

r, s

occur to the unit or surrounding

 

 

 

items if unit is tipped. Use a

 

 

ramp if loading or unloading

 

 

the unit from a height of more

 

T

than 12" (30.5 cm).

 

 

R

Lifting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning: Risk injury from lifting. Unit weighs more than 160 lbs.

(72.6 kg) Do not move or lift without assistance.

 

Always use at least two people when lifting and lift from the recommended lift points (S).

MOVING

1.Grasp handle (T) of compressor, and lift compressor high enough so unit can be rolled on the front tire(s).

Warning: Risk of unsafe operation. Ensure proper footing and use caution when rolling compressor so that unit does not tip or cause loss of balance.

2.When location is reached slowly lower compressor to ground. Always store compressor in a horizontal position.

NOTE: Should the unit tip over, hard starting and smoking will occur due to oil spillage.

Preparation For Use

Pre-Start Checklist (Fig. 1)

1.Ensure engine START/RUN/OFF switch (C) is in the OFF position.

2.Ensure air tank is drained, see Draining Air Tank under Maintenance.

3.Ensure the drain valve (J) is closed.

4.Ensure safety valve (I) is functioning properly, see Checking Safety Valve under Maintenance.

5.Check pump oil level, see Compressor Pump Oil under Maintenance.

CAUTION: Do not operate without oil or with inadequate oil.DeWALT is not responsible for compressor failure caused by inadequate oil.

6.Check engine's oil and fuel level, see engine's instruction manual for correct procedures.

7.Visually inspect drive belt. Replace belt if frayed, cracked, or worn. NOTE: Outer belt cover must be removed to inspect drive belt.

8.Ensure all guards, covers, and labels are in place, legible (for labels) and securely mounted. Do not use compressor until all items have been verified.

Initial Set-up (Fig. 1)

WARNING: Do not operate this unit until you read this instruction manual and the engine instruction manual for safety, operation and maintenance instructions.

18

Image 18
Contents D55690, D55695 Air Compressor Pump Air Intake Filter B. Engine Air FilterD55695 Specifications Pump SpecificationsEngine Specifications Hot SurfacesWhat can happen How to prevent it Definitions Safety GuidelinesImportant Safety Instructions Save these instructionWhat can happen Transporting or storing Attachments & accessories Fly apart, and could result in serious injuryTires Attempting maintenance Always wear certified safetyMaintenance until unit has Equipment Ansi Z87.1 eyeMoving parts such as By a DeWALT factory serviceService center Your clothingImportant Safety Instructions for All Battery Packs Read all InstructionsSpecific Safety instructions for Lithium Ion Li-Ion Rbrc Seal25 ft 50 ft 75 ft 100 ft 125 ft 150 ft 175 ft Important Safety Instructions for all Battery ChargersWire Size AWG Do not operate charger with damaged cord or plugIndicator Light Operation Using Automatic Tune-Up ModeCharging Procedure ChargersProblem Power Line Charge IndicatorsHot/cold Pack DelaY Leaving the battery pack in the chargerFeatures Safety ValveStorage Recommendations AIR Tank Drain Valve Assembly FigAIR Intake Filter Regulated Pressure GaugeCompatibility LocationTransporting Lifting Preparation For Use Pre-Start Checklist FigInitial Set-up Fig Kg Do not move or lift without assistanceBreak-in Procedure This procedure is required ProcedureRecoil Start Operating Procedures Start-up Fig Follow Pre-Start Checklist under Preparation for UseTurn the engine START/RUN/OFF switch C to the RUN position Procedure Daily Weekly Monthly Year or MaintenanceMaintenance Chart Shut-downChecking Safety Valve Fig Checking Air Filter Element FigDraining Air Tank Fig Air tank causing a risk of air tank rupture Compressor Pump Oil FigChecking oil Changing oil Adjusting Belt Tension Checking Belt Tension FigPulley and Flywheel­ Alignment Repairs Accessories Service InformationFull One Year Warranty Date and Place of PurchaseGlossary Troubleshooting Guide Problem CodeCode Possible cause Troubleshooting CodesPossible Solution Erwise modify air tank or it will weaken. The air tank canSee Motor Pulley/Flywheel Alignment under Maintenance Compressor Pump Oil under Maintenance Procedure Regulator open Engine fuel tank emptyPush knob in to lock in place Compresseur d’air Surfaces chaudes Caractéristiques techniques de la pompeCaractéristiques techniques du moteur Fiche techniqueMineures ou modérées Définitions lignes directrices en Matière de sécuritéDirectives de sécurité importantes Composer Sans Frais LE 1-800-4-DeWALTCE QUI Peut SE Produire Du compresseur ne devrait Installer correctement desFiltres convenables et un Jamais être utilisé pourCE QUI Peut SE Produire Comment L’ÉVITER Attachements et accessoires PneusLe manomètre pour empêcher un surgonflage CSA Z94.3 munie d’écrans Des accessoiresDe sécurité homologué CompresseurEndommagés ou retirés Ne jamais utiliser leOu les couvercles sont Garder les cheveux, lesLire toutes les directives Avertissement Risque d’incendie. Ne pas Le sceau Srprc 25 pi Calibre AWGNE Jamais tenter de relier deux chargeurs ensemble Procédure de charge Utilisation du mode tune-up automatiqueChargeurs Fonctionnement du voyant Voyants de chargeProblème avec le secteur Remarques importantes pour le chargementFonction de suspension du bloc-piles chaud/froid Bloc-piles laissé dans le chargeurDémarrage Électrique Recommandations d’entreposageCaractéristiques BLOC-PILES ET Chargeur DE 18 VoltsSoupape DE Purge DU Réservoir D’AIR Soupape DE SûretéFiltre D’ADMISSION D’AIR Manomètre DU Réservoir D’AIREmplacement Assemblage figCompatibilité Déplacement TransportREMARQUE  Mode d’emploi Liste de vérification de pré-démarrage fig Réglage initial figProcédure de rodage La procédure suivante est requise  Démarrage à rappel Démarrage électriqueProcédures de fonctionnement Démarrage fig Régulateur sous Caractéristiques ArrêtEntretien Étapes 3 àProgramme d’entretien Vérification de la soupape de sûreté figVérification des éléments du filtre d’air fig Vidange du réservoir d’air fig Huile de la pompe du compresseur figVérification de l’huile Vérification de la tension de la courroie Fig Vidange d’huileRéglage la tension de la courroie Alignement de la poulie et du volantAccessoires Information sur les réparations RéparationsGarantie complète d’un 1 an Glossaire 13, 14, 16, 19 Guide de dépannageProblème Code SifflementCode Cause possible Est requis pour l’utilisation de l’accessoireCodes de dépannage Rompre ou d’exploserFixation bien serrées Réglage de la tension de la courroie sous EntretienAvertissement Risque d’éclatement. Des vibrations Ne jamais utiliser l’appareil sans le support du raidisseurConsulter la rubrique Alignement de la poulie-moteur Volant sous EntretienCompresseur sous Entretien Ouverte Compresor de aire D55690ATapón de drenaje de aceite de la bomba Superficies calientes Especificaciones de la bombaEspecificaciones del motor EspecificacionesPeligro Riesgo de explosión o incendio Instrucciones de seguridad importantesGuarde estas instrucciones ¿Qué puede suceder? Cómo evitarloPeligro Riesgo Respiratorio asfixia Advertencia Riesgo de explosión Neumáticos ¿Qué puede suceder?Elementos y accesorios NeumáticoAdvertencia Riesgo por piezas móviles Advertencia Riesgo de operación insegura Lea todas las instrucciones Advertencia Riesgo de incendio. No guarde Sin embargo, si el sello externo está rotoEl sello Rbrc Tamaño AWG del conductor Utilización del modo Tune-Up automáticoPies 50 pies Nunca intente conectar 2 cargadores juntosOperación de la luz indicadora Indicadores de carga CargadoresProcedimiento de carga Retraso por paquete caliente/fríoLínea de potencia con problemas Notas importantes sobre la cargaDejar el paquete de baterías en el cargador Arranque Eléctrico Recomendaciones con respecto al almacenamientoCaracterísticas Paquete DE Baterías Y Cargador DE 18Válvula DE Drenaje DEL Tanque DE Aire Ensamblaje FigFiltro DE Entrada DE Aire Manómetro ReguladoLubricación y aceite CompatibilidadLugar Transporte Áreas húmedasConsideraciones sobre el ruido Levantar la unidadConfiguración inicial Fig Arranque de retroceso Arranque eléctricoProcedimientos operativos Puesta en marcha Fig Apagado MantenimientoControlar el elemento del filtro de aire Tabla de mantenimientoControlar la válvula de seguridad Fig ProcedimientoColoque el elemento nuevamente en la base del filtro Drenar el tanque de aire FigAceite de la bomba del compresor Controlar el aceiteControlar la tensión de la correa Fig Cambio de aceiteOFF apagado Espere que la unidad Ajustar la tensión de la correaAlineación de la correa y el volante Se enfríe Desconecte el cable de La bujía Drene Tanque AireReparaciones AccesoriosInformación del servicio técnico Póliza de GarantíaGarantía completa de un año ExcepcionesGlosario Para Otras LocalidadesGuía de detección de problemas Problema CódigoSolución Posible Códigos de detección de problemasCódigo Causa posible Advertencia Riesgo de explosión. No perfore, suelde niConsulte Alineación de la polea y el volante en la sección Tornillos de montaje se deben mantener ajustadosQue esté equipada con el soporte de la barra tensora MantenimientoConsulte Aceite de la bomba del compresor en la sección Tanque de combustible del motor vacío Al de instrucciones del motorEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD JUN08 Part No. N000707Copyright 2008 D eWALT