Epson DW746 To adjust, To Install the SAW Blade, Install and Adjust the Throat Plate FIG

Page 10

ADJUSTING THE REAR FENCE GLIDE (FIG. 13)

INSTALL THE GUARD AND SPLITTER ASSEMBLY (FIG. 16)

English

1. Slide the rip fence (G) back FIG.13 and forth to check if it slides

freely over the rails.

2.Lock the rip fence in place using the rail locking lever (I).

If there is excessive up/down movement in the rear of the fence when locking, the rear fence bracket (LL) needs adjustment.

To adjust:

1.Loosen the screws (MM).

2.Set the retaining clip (NN) so

that it slightly pushes on the rear rail (A).

3.Tighten the screws.

MM

NN

LL

A

CAUTION: To prevent snagging of the workpiece, the table insert should be flush or slightly below the surface of the table top and secured in place. The rear of the throat plate should be flush or slightly above the table top. Refer to Install and Adjust Throat Plate.

CAUTION: When installing the throat plate, always make certain to hold on to the blade guard. The insert will automatically release the holding action on the splitter and lower the blade guard when it is installed in the table opening.

1.

Raise the blade to its highest

FIG. 16

C

 

 

point.

 

 

 

2.

Loosen the outer guard

 

TT

SS

 

retaining nuts (SS) enough so

 

 

 

 

the splitter (C) will fit between

 

 

 

 

the two guard retaining plates

 

 

 

 

(TT).

 

UU

 

3.

Install the splitter (C).

 

 

 

 

 

4.Ensure the fence still slides smoothly. If it does not, the retaining clip (NN) is pushing on the rear rail (A) too strongly.

TO INSTALL THE SAW BLADE (FIG.14)

WARNING: Use ONLY 10" (254 mm) diameter blades with 5/8" (16 mm) arbor holes, rated at 3600rpm or higher.

WARNING: To reduce the risk of injury. Wear gloves when handling saw blades.

4. Using a straight edge, check

 

to ensure the splitter is prop-

TT

erly aligned with the blade. If

 

not, the position is adjusted

 

by moving the inner guard

 

clamp nuts (UU) to change

 

the location the splitter. Make

 

1.Set the blade arbor highest position using the blade height adjustment wheel (M).

2.Remove the nut (OO) and outer clamp washer (PP)

3.Place the blade (D) onto the arbor with the teeth pointing towards the front of the saw.

4.Remount the outer clamp washer (PP) and nut (OO) as shown. Make sure that the saw blade is piloted on the outer clamp washer hub (QQ).

5Use the spindle lock wrench and blade wrench to tighten the nut.

FIG. 14

BLADE WRENCH

SPINDLE

LOCK

WRENCH

QQ

PP

OO

 

D

sure there is some clearance

between the splitter and the blade and the blade spins freely. If the splitter is tilted rela-

tive to the blade, the splitter plate can be bent until it lines up correctly. IMPORTANT:

THE GUARD SHOULD BE IN PLACE FOR ALL POSSIBLE CUTS. When making non-

through cuts, the guard can be easily removed by slightly loosening the outer guard nuts

(SS). The guard can easily be replaced without having to readjust the inner nuts.

INSTALL AND ADJUST THE THROAT PLATE (FIG. 17)

CAUTION: To reduce the risk of injury. The throat plate must be in place at all times.

1. Align the throat plate (VV) as shown

FIG. 17

and insert the tabs on the back of the

 

throat plate into the holes at the back

 

of the table and lower the plate into its

VV

opening.

2. The throat plate includes four adjust-

NOTE: If the nut fall into the interior of the saw, carefully remove it though the dust port.

ADJUST THE FENCE SCALE INDICATOR (FIG. 15).

1.

Slide the fence until it just

FIG. 15 U

 

touches the blade.

 

 

2.

Loosen the fence indicator

RR

 

screw (RR) and slide it until

 

 

the hairline aligns with the “0”

 

 

line on the scale.

 

3.

Tighten the screw.

 

4.

If the low profile fence face

 

 

accessory or a wider home-

 

 

made fence face is used

RR

 

which is out of the adjust-

 

ment range of the pointer, the

U

 

 

 

pointer (U) can be removed completely, turned 180 degrees, re-installed, and aligned

 

with the “0” line.

 

ment screws which raise or lower it. When properly adjusted, the front of the throat plate should be flush or slightly below the surface of the table top, and the rear of the throat plate should be flush or slightly above the table top. The center front screw, when turned clockwise, will engage a cam under the front lip of the table, locking the throat plate in place. Rotate the screw counterclockwise 1/2 turn to remove the throat plate.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Dewalt Page Volt, Single-Phase Operation Definitions Safety GuidelinesGeneral Safety Rules Grounding InstructionsPolarized Plugs Important Safety InstructionsAdditional Safety Rules for Table Saws Minimum Gauge for Cord SetsMaking a Push Stick Inside Back Cover SAW Blade Guard and SpreaderKickbacks Hardware Included with the DW746 Woodworker’s Table Saw For Future USEDW746 Basic Unit SpecificationsFeatures Fig Tools IncludedAssembly UnpackingAttach the Left & Right Side Support Tables FIG Adjusting Fence to Table TOP FIGAdjusting the Fence Face Assemble the Fence Beam to the Fence HeadInstall and Adjust the Throat Plate FIG To adjustTo Install the SAW Blade Adjust the Fence Scale Indicator FIGRip Fence Operation Operation On-Off Switch FigSaw Blades CuttingCrosscutting Bevel RippingRipping Small Pieces Bevel CrosscuttingCleaning MaintenanceDust Collection Lubricating Fence Head AccessoriesThree Year Limited Warranty Maintaining Fence SystemTroubleshooting Conserver CES Directives Définitions lignes directrices en Matière de sécuritéRègles de sécurité générales Directives relatives à la mise à la terreFiches Polarisées Double isolationDirectives de sécurité importantes Calibre Minimum Pour RallongeFrançais PROTÈGE-LAME ET Couteau Séparateur Conserver CES Directives Pour UN Usage UltérieurEffets DE Rebond Outils à fournir Appareil de base DW746Outils compris Quincaillerie nécessaireDésemballage Installer LA Manivelle DE BISEAU. FIGCaractéristiques fig AssemblageConsulter les Directives Assembler LA Barre DE Guidage Avant ET LES Supports FIGIl vous faut les articles suivants Fixer LES Tables DE Soutien Gauche ET Droite FIGRégler LA Face DU Guide FIG Réglage DU Guide Avec LE Dessus DE Table FIGAlignement DU Guide DE Sciage EN Long Assembler LA Poutre DU Guide À LA Tête DU Guide FIGPour Installer LA Lame DE Scie Pour effectuer le réglage, procéder comme suitRégler L’ÉCHELLE DE Biseau FIG Installer ET Régler LA Plaque DE Lumière FIGInstaller LE Couvercle DU Moteur FIG Mettre LA Scie AU Niveau FIGLames de scie Fonctionnement du guide longitudinalInterrupteur Marche/Arrêt Fig FonctionnementSciage en long de petites pièces Sciage en longSciage sur le long en biseau TronçonnageCoupe à rainure Tronçonnage en biseauDécoupe à l’onglet DépoussiérageLubrification de la tête du guide EntretienNettoyage Maintien du système du guideGarantie limitée trois ans AccessoiresRéparations DépannageCoincement DU Matériau Durant LA Mesures À Prendre Coupe LA Machine Vibre DE Manière Mesures À Prendre ExcessiveCoupes D’ONGLET Imprécises Mesures À Prendre Coupes DE Sciage EN Long Mesures À Prendre ImprécisesConserve Estas Instrucciones Definiciones Normas de seguridadInstrucciones de seguridad importantes Instrucciones de conexión a tierraEnchufes Polarizados Doble aislamientoCalibre Mínimo Para LOS Juegos DE Cables Normas de seguridad adicionales para las sierras de banco Varas DE Empuje Cara Interna de la Contratapa Protector DE LA Hoja Y HendedorRetrocesos Herramientas incluidas EspecificacionesUnidad básica DW746 Artículos de ferretería necesariosEnsamblaje Características FigDesembalaje Instale LA Manivela DE Biselado FIGEnsamble EL Riel Delantero Y LAS Abrazaderas FIG Sujete EL Riel Trasero a LA Parte Superior DEL Banco FIGAjuste LA Cara DE LA Guía FIG Ajuste LA Guía a LA Parte Superior DEL Banco FIGEnsamble LA Barra DE LA Guía a LA Cabeza DE LA Guía FIG Instalar EL Conjunto DE Hendedor Y Protector Fig Deslice la Guía de cortePara ajustar Para Instalar LA Hoja DE LA SierraInstale LA Cubierta DEL Motor FIG Instalación Y Ajuste DE LA Placa Para Ranuras FIGAjuste LA Escala DE Biselado FIG Nivele LA Sierra FIGHojas para sierras Funcionamiento de la guía de corte longitudinalInterruptor de encendido/ apagado Fig FuncionamientoCortes longitudinales de piezas pequeñas Corte longitudinalCortes longitudinales en bisel Cortes transversalesCortes a inglete compuestos Cortes transversales en biselCortes a inglete Corte de ranurasMantenimiento Colector de polvoLimpieza Accesorios Lubrique la cabeza de guíaMantenimiento del sistema de guía ReparacionesPóliza de Garantía Garantía limitada de tres añosDetección de problemas Manivelas DE Altura O QUÉ Hacer Biselado Difíciles DE Girar Polvo Colector QUÉ Hacer Obstrucciones

DW746 specifications

The Epson DW746 is a powerful and versatile all-in-one printer designed for business and professional use. Known for its reliability and high-quality output, the DW746 caters to a wide range of printing needs, making it an ideal choice for offices and small workgroups.

One of the main features of the DW746 is its fast printing speed. It can produce up to 25 pages per minute for monochrome documents and approximately 12 pages per minute for color prints. This efficiency ensures that users can handle large workloads without experiencing frustrating delays.

In addition to speed, the Epson DW746 offers exceptional print quality. With a maximum print resolution of 4800 x 1200 dpi, it delivers sharp text and vibrant colors. This makes it suitable for a variety of printing tasks, from professional documents to marketing materials and high-quality photos.

The DW746 utilizes PrecisionCore technology, which is a key aspect of Epson's printing process. This technology employs an array of micro-fine nozzles to create extremely precise dots of ink, resulting in superior print quality and consistency. PrecisionCore also enhances the printer's durability and longevity, ensuring that it remains a reliable workhorse for years to come.

Another notable feature is the DW746's connectivity options. It supports a variety of connectivity methods, including USB, Ethernet, and Wi-Fi, allowing users to print directly from their computers, mobile devices, or even cloud services. This flexibility makes it easy to integrate the printer into any office setup, promoting seamless workflow and collaboration.

The printer is equipped with an automatic duplex printing feature, which allows for double-sided printing. This not only saves paper but also helps businesses to reduce their overall printing costs and environmental impact.

Additionally, the Epson DW746 has a robust paper handling capacity. It comes with a standard paper tray that can hold up to 250 sheets, along with a rear manual feed slot for specialty media. For larger print jobs, users can also equip the printer with optional paper trays to increase storage capacity.

In conclusion, the Epson DW746 stands out as a powerful all-in-one solution for businesses seeking speed, quality, and versatility. With advanced printing technologies, robust connectivity options, and efficient paper handling capabilities, it meets the demands of modern office environments while delivering impressive results.
Top Page Image Contents