Epson DW746 instruction manual Rip Fence Operation

Page 11

ADJUST THE BEVEL STOPS (FIG. 18)

1. Using a square, set the blade FIG. 18 to exactly “0” degrees. If the blade stops beveling before it

gets to 0, loosen the stop set screw (located in the left miter guide slot) with the 5 mm hex wrench and then proceed to “0” degrees. With

the blade set at 0, slowly turn the zero stop screw in until

LEVEL THE SAW (FIG. 21)

FIG. 21

1. Place the saw in the location it is going to be used.

 

2. If the saw rocks on the floor, the foot not touching the floor can

 

be lowered to compensate for the uneven floor.

ZZ

a. Loosen the two screws (ZZ) that hold the foot (L) to the leg.

L

Let the foot fall to the floor surface.

 

b. Retighten the screws holding the foot to the leg.

 

If your saw will have a permanent location, we recommend bolting

 

the feet to the floor using the holes provided.

 

ADJUSTMENT AND USE OF MITER GAUGE (FIG. 22)

 

English

you feel resistance. Bevel the blade away from 0 a little then back to the stop.

2.Remeasure the angle and repeat the stop adjustment as necessary until the blade stops at 0 degrees.

3.Set the 45 stop the same way. The set screw for the 45° stop is located in the right hand miter guide slot.

For some special cuts, the stops can be backed out and the saw will bevel from –2 degrees to 47 degrees.

ADJUST THE BEVEL SCALE (FIG. 19)

Your miter gauge features adjustable FIG. 22 stops at 90° and 45° left and right.

To adjust these stops:

a. Loosen the lock nuts (A1) and tighten or loosen the three adjusting screws (A2).

b. Check the gauge with a square

against the blade and tighten

the three adjusting screws.

c. To set the miter gauge past

the 45 degree stops, flip up the

30

45

60 75

90

30

45

60 75

A3

A2

A1

1.Bevel the saw until it hits the zero bevel stop.

2.Remove the lock knob (BB) and blade height adjustment wheel (M).

3.Adjust the red pointer by loosening the screw (WW) where it attaches to its shaft, move the pointer until it lines up with the 0 line on the scale, and retighten the screw. The pointer should be positioned just barely off of the scale surface.

FIG. 19

XX

 

M

BB

 

 

WW

 

XX

stop plate (A3) and continue to

the required angle.

CLEAN THE TABLE TOP

Your saw was shipped with a rust preventive coating which should be removed. Clean the top with mineral spirits or denatured alcohol and apply paste wax. Apply and remove soon after- ward to prevent a sticky build-up.

Rip Fence Operation

RAIL LOCK LEVER (FIG. 23)

The rail lock lever (I) locks the fence in place preventing movement during FIG. 23 cutting. To lock the rail lever, push it down and toward the rear of the saw. To unlock, pull it up and toward the front of the saw. NOTE: When ripping, always lock the rail lock lever.

4.Bevel the saw to the 45º stop. If the pointer doesn’t point to 45º, loosen the two screws (XX) which hold the scale to the saw front panel and slide the scale up or down until the pointer lines up with the 45 line. Retighten the scale screws.

5.Replace the blade height adjustment wheel and lock knob.

INSTALL THE MOTOR COVER (FIG. 20)

 

1.

Remove the two cover screws and washers (YY) from

FIG. 20

 

the top of the two side legs with a small flat blade

 

screwdriver.

 

2.

Snap the two bottom tabs of the cover (J) into the slots

YY

 

in the right lower crossmember.

3. Place the cover in position and reinstall the screws and washers.

J

RIP SCALE POINTER

 

NOTE: The rip scale pointer will need to be readjusted whenever a

 

thicker or thinner blade is installed. Should you decide to use a thicker

 

face, or the DEWALT low fence face accessory, the scale pointer may be

 

removed and turned 180° to line up with the scale. Refer to Adjust the

 

Fence Scale Indicator under Assembly.

I

RIP FENCE CAPACITY

The rip fence will slide beyond the end of the rails in either direction with- out falling off. Stops are provided to keep the fence attached.

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Dewalt Page Grounding Instructions Definitions Safety GuidelinesGeneral Safety Rules Volt, Single-Phase OperationMinimum Gauge for Cord Sets Important Safety InstructionsAdditional Safety Rules for Table Saws Polarized PlugsKickbacks SAW Blade Guard and SpreaderMaking a Push Stick Inside Back Cover For Future USE Hardware Included with the DW746 Woodworker’s Table SawTools Included SpecificationsFeatures Fig DW746 Basic UnitUnpacking AssemblyAssemble the Fence Beam to the Fence Head Adjusting Fence to Table TOP FIGAdjusting the Fence Face Attach the Left & Right Side Support Tables FIGAdjust the Fence Scale Indicator FIG To adjustTo Install the SAW Blade Install and Adjust the Throat Plate FIGRip Fence Operation Cutting On-Off Switch FigSaw Blades OperationBevel Crosscutting Bevel RippingRipping Small Pieces CrosscuttingDust Collection MaintenanceCleaning Maintaining Fence System AccessoriesThree Year Limited Warranty Lubricating Fence HeadTroubleshooting Directives relatives à la mise à la terre Définitions lignes directrices en Matière de sécuritéRègles de sécurité générales Conserver CES DirectivesCalibre Minimum Pour Rallonge Double isolationDirectives de sécurité importantes Fiches PolariséesFrançais Effets DE Rebond Conserver CES Directives Pour UN Usage UltérieurPROTÈGE-LAME ET Couteau Séparateur Quincaillerie nécessaire Appareil de base DW746Outils compris Outils à fournirAssemblage Installer LA Manivelle DE BISEAU. FIGCaractéristiques fig DésemballageFixer LES Tables DE Soutien Gauche ET Droite FIG Assembler LA Barre DE Guidage Avant ET LES Supports FIGIl vous faut les articles suivants Consulter les DirectivesAssembler LA Poutre DU Guide À LA Tête DU Guide FIG Réglage DU Guide Avec LE Dessus DE Table FIGAlignement DU Guide DE Sciage EN Long Régler LA Face DU Guide FIGPour effectuer le réglage, procéder comme suit Pour Installer LA Lame DE ScieMettre LA Scie AU Niveau FIG Installer ET Régler LA Plaque DE Lumière FIGInstaller LE Couvercle DU Moteur FIG Régler L’ÉCHELLE DE Biseau FIGFonctionnement Fonctionnement du guide longitudinalInterrupteur Marche/Arrêt Fig Lames de scieTronçonnage Sciage en longSciage sur le long en biseau Sciage en long de petites piècesDépoussiérage Tronçonnage en biseauDécoupe à l’onglet Coupe à rainureMaintien du système du guide EntretienNettoyage Lubrification de la tête du guideDépannage AccessoiresRéparations Garantie limitée trois ansCoupes DE Sciage EN Long Mesures À Prendre Imprécises LA Machine Vibre DE Manière Mesures À Prendre ExcessiveCoupes D’ONGLET Imprécises Mesures À Prendre Coincement DU Matériau Durant LA Mesures À Prendre CoupeInstrucciones de conexión a tierra Definiciones Normas de seguridadInstrucciones de seguridad importantes Conserve Estas InstruccionesCalibre Mínimo Para LOS Juegos DE Cables Doble aislamientoEnchufes Polarizados Normas de seguridad adicionales para las sierras de banco Retrocesos Protector DE LA Hoja Y HendedorVaras DE Empuje Cara Interna de la Contratapa Artículos de ferretería necesarios EspecificacionesUnidad básica DW746 Herramientas incluidasInstale LA Manivela DE Biselado FIG Características FigDesembalaje EnsamblajeSujete EL Riel Trasero a LA Parte Superior DEL Banco FIG Ensamble EL Riel Delantero Y LAS Abrazaderas FIGEnsamble LA Barra DE LA Guía a LA Cabeza DE LA Guía FIG Ajuste LA Guía a LA Parte Superior DEL Banco FIGAjuste LA Cara DE LA Guía FIG Para Instalar LA Hoja DE LA Sierra Deslice la Guía de cortePara ajustar Instalar EL Conjunto DE Hendedor Y Protector FigNivele LA Sierra FIG Instalación Y Ajuste DE LA Placa Para Ranuras FIGAjuste LA Escala DE Biselado FIG Instale LA Cubierta DEL Motor FIGFuncionamiento Funcionamiento de la guía de corte longitudinalInterruptor de encendido/ apagado Fig Hojas para sierrasCortes transversales Corte longitudinalCortes longitudinales en bisel Cortes longitudinales de piezas pequeñasCorte de ranuras Cortes transversales en biselCortes a inglete Cortes a inglete compuestosLimpieza Colector de polvoMantenimiento Reparaciones Lubrique la cabeza de guíaMantenimiento del sistema de guía AccesoriosGarantía limitada de tres años Póliza de GarantíaDetección de problemas Polvo Colector QUÉ Hacer Obstrucciones Manivelas DE Altura O QUÉ Hacer Biselado Difíciles DE Girar

DW746 specifications

The Epson DW746 is a powerful and versatile all-in-one printer designed for business and professional use. Known for its reliability and high-quality output, the DW746 caters to a wide range of printing needs, making it an ideal choice for offices and small workgroups.

One of the main features of the DW746 is its fast printing speed. It can produce up to 25 pages per minute for monochrome documents and approximately 12 pages per minute for color prints. This efficiency ensures that users can handle large workloads without experiencing frustrating delays.

In addition to speed, the Epson DW746 offers exceptional print quality. With a maximum print resolution of 4800 x 1200 dpi, it delivers sharp text and vibrant colors. This makes it suitable for a variety of printing tasks, from professional documents to marketing materials and high-quality photos.

The DW746 utilizes PrecisionCore technology, which is a key aspect of Epson's printing process. This technology employs an array of micro-fine nozzles to create extremely precise dots of ink, resulting in superior print quality and consistency. PrecisionCore also enhances the printer's durability and longevity, ensuring that it remains a reliable workhorse for years to come.

Another notable feature is the DW746's connectivity options. It supports a variety of connectivity methods, including USB, Ethernet, and Wi-Fi, allowing users to print directly from their computers, mobile devices, or even cloud services. This flexibility makes it easy to integrate the printer into any office setup, promoting seamless workflow and collaboration.

The printer is equipped with an automatic duplex printing feature, which allows for double-sided printing. This not only saves paper but also helps businesses to reduce their overall printing costs and environmental impact.

Additionally, the Epson DW746 has a robust paper handling capacity. It comes with a standard paper tray that can hold up to 250 sheets, along with a rear manual feed slot for specialty media. For larger print jobs, users can also equip the printer with optional paper trays to increase storage capacity.

In conclusion, the Epson DW746 stands out as a powerful all-in-one solution for businesses seeking speed, quality, and versatility. With advanced printing technologies, robust connectivity options, and efficient paper handling capabilities, it meets the demands of modern office environments while delivering impressive results.
Top Page Image Contents