Epson DW746 instruction manual Unpacking, Assembly

Page 8

English

Unpacking

WARNING: To reduce the risk of injury, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual.

1.Remove parts box, motor cover, fence beam, side tables and fence rails (DW746X).

2.Turn the saw to the upright position.

CAUTION: Use a minimum of two people to prevent personal injury when turning the saw and stand upright. The combined weight of the table top and motor assembly is approxi- mately 200 lbs (91 kg).

3.Cut and remove plastic strap holding the motor.

4.Using front hand crank, lower the motor some and remove the foam packing material between the motor and the mechanism.

Assembly

WARNING: To reduce the risk of injury, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual.

PLEASE READ ENTIRE ASSEMBLY SECTION BEFORE PROCEEDING.

INSTALL BEVEL CRANK (FIG. 2)

 

 

 

FIG. 2

1. Install the blade height adjustment wheel (M)

M

over the shaft (AA), rotate it

slightly

to

fully

 

5.Tighten nut finger tight.

6.Repeat for other three brackets.

ATTACH FRONT RAIL WITH BRACKETS TO THE TABLE TOP (FIG. 5)

You will need:

2

– 10 x 30 mm Flat Head FIG. 5

B

 

 

Screws

 

 

2

–10 mm Flat Washers

 

 

2

– 10 mm Lock Washers

CC

 

2

– 10 mm Nuts

 

 

1. Secure each screw through the upper hole

 

in the center rail brackets (CC) keeping the

 

flat washer, lock washer and nut on the

CC

inside of the table (B).

 

2.Tighten snug, do not overtighten. Tighten center rail bracket nuts, leaving the outer nuts finger tight.

ATTACH REAR RAIL TO THE TABLE TOP (FIG. 6)

You will need:

2

– 10 x 35 mm

 

 

Hex Head Bolts

 

2

– 10 mm Flat Washers

 

2

– 10 mm Lock Washers

 

engage the shaft pin.

AA

 

2.

Screw the lock knob (BB) into place until it is

 

 

 

 

fully seated, then back it off 1/4 to 1/2 turn.

 

 

3.

Turn blade height adjustment wheel (M) to raise BB

 

 

mechanism as high as it will go.

 

 

INSTALL WRENCH HOOK (FIG. 3)

 

 

NOTE: Always hang the blade wrench, spindle lock

 

FIG. 3

wrench and push stick on wrench hook when not in use.

 

1.

Located the plastic threaded insert at the top of the front right leg.

K

2.

Thread the “L” shaped wrench hook (K) in until only a few threads are

 

visible.

 

 

ASSEMBLE FRONT RAIL AND BRACKETS (FIG. 4)

IMPORTANT: DW746X includes a 30" precision fence rail system. A 30" or

2 – 10 mm Nuts

1. Secure rear fence rail (A) to FIG. 6 table top (B) using hex head bolts, washers, lock washers

and nuts. Keep the washers and nuts on the inside of the table. The flat side should be down unless you are also mounting an accessory (consultaccessoryinstructions for rail mounting details). Make sure ends of the rear rail line up with the ends of the front rail.

B

B

A

A

52" precision rail system for the DW746 may be purchased at additional cost. Always fol- low the instructions included with the accessory. After assembling the rail system, refer to

Parallel the Rails to the Table Top.

If you need assistance with this accessory, please call 1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com.

You will Need: 4 – 8 mm Carriage Bolts

DD

FIG. 4

4 – 8 mm Lock Washers

4 – 8 mm Nuts

1. Unpack rail carton (contains front and rear rail).

2. Place the carriage bolts into each rail bracket (CC) as shown.

3. Place lock washers and nuts onto carriage bolts and tighten the nuts a few threads.

4. Place the head of the carriage bolt into keyhole slots in

 

the front rail and slide to engage the square part of the

CC

bolt. Make sure the rip scale (DD) on the front rail and all

 

four brackets are facing up.

 

2. Tighten snug, do not overtighten.

PARALLEL THE RAILS TO THE TABLE TOP (FIG. 7)

1. Use the fence face (F) to extend the table FIG. 7 surface over the front fence rail (Q).

2. Use a ruler to measure the distance between the table top and the rail at both ends of the table top. The distance should be equal at both ends.

3.If adjustment is needed, loosen the mount- ing screws slightly and tap on the rail brack- ets with a soft hammer or regular hammer

and a block of wood until the distances are the same.

4.Tighten fasteners securely.

5.Repeat for the rear fence rail (A).

F

A

Q

6

Image 8
Contents Dewalt Page Definitions Safety Guidelines General Safety RulesVolt, Single-Phase Operation Grounding InstructionsImportant Safety Instructions Additional Safety Rules for Table SawsPolarized Plugs Minimum Gauge for Cord SetsKickbacks SAW Blade Guard and SpreaderMaking a Push Stick Inside Back Cover Hardware Included with the DW746 Woodworker’s Table Saw For Future USESpecifications Features FigDW746 Basic Unit Tools IncludedAssembly UnpackingAdjusting Fence to Table TOP FIG Adjusting the Fence FaceAttach the Left & Right Side Support Tables FIG Assemble the Fence Beam to the Fence HeadTo adjust To Install the SAW BladeInstall and Adjust the Throat Plate FIG Adjust the Fence Scale Indicator FIGRip Fence Operation On-Off Switch Fig Saw BladesOperation CuttingBevel Ripping Ripping Small PiecesCrosscutting Bevel CrosscuttingDust Collection MaintenanceCleaning Accessories Three Year Limited WarrantyLubricating Fence Head Maintaining Fence SystemTroubleshooting Définitions lignes directrices en Matière de sécurité Règles de sécurité généralesConserver CES Directives Directives relatives à la mise à la terreDouble isolation Directives de sécurité importantesFiches Polarisées Calibre Minimum Pour RallongeFrançais Effets DE Rebond Conserver CES Directives Pour UN Usage UltérieurPROTÈGE-LAME ET Couteau Séparateur Appareil de base DW746 Outils comprisOutils à fournir Quincaillerie nécessaireInstaller LA Manivelle DE BISEAU. FIG Caractéristiques figDésemballage AssemblageAssembler LA Barre DE Guidage Avant ET LES Supports FIG Il vous faut les articles suivantsConsulter les Directives Fixer LES Tables DE Soutien Gauche ET Droite FIGRéglage DU Guide Avec LE Dessus DE Table FIG Alignement DU Guide DE Sciage EN LongRégler LA Face DU Guide FIG Assembler LA Poutre DU Guide À LA Tête DU Guide FIGPour Installer LA Lame DE Scie Pour effectuer le réglage, procéder comme suitInstaller ET Régler LA Plaque DE Lumière FIG Installer LE Couvercle DU Moteur FIGRégler L’ÉCHELLE DE Biseau FIG Mettre LA Scie AU Niveau FIGFonctionnement du guide longitudinal Interrupteur Marche/Arrêt FigLames de scie FonctionnementSciage en long Sciage sur le long en biseauSciage en long de petites pièces TronçonnageTronçonnage en biseau Découpe à l’ongletCoupe à rainure DépoussiérageEntretien NettoyageLubrification de la tête du guide Maintien du système du guideAccessoires RéparationsGarantie limitée trois ans DépannageLA Machine Vibre DE Manière Mesures À Prendre Excessive Coupes D’ONGLET Imprécises Mesures À PrendreCoincement DU Matériau Durant LA Mesures À Prendre Coupe Coupes DE Sciage EN Long Mesures À Prendre ImprécisesDefiniciones Normas de seguridad Instrucciones de seguridad importantesConserve Estas Instrucciones Instrucciones de conexión a tierraCalibre Mínimo Para LOS Juegos DE Cables Doble aislamientoEnchufes Polarizados Normas de seguridad adicionales para las sierras de banco Retrocesos Protector DE LA Hoja Y HendedorVaras DE Empuje Cara Interna de la Contratapa Especificaciones Unidad básica DW746Herramientas incluidas Artículos de ferretería necesariosCaracterísticas Fig DesembalajeEnsamblaje Instale LA Manivela DE Biselado FIGEnsamble EL Riel Delantero Y LAS Abrazaderas FIG Sujete EL Riel Trasero a LA Parte Superior DEL Banco FIGEnsamble LA Barra DE LA Guía a LA Cabeza DE LA Guía FIG Ajuste LA Guía a LA Parte Superior DEL Banco FIGAjuste LA Cara DE LA Guía FIG Deslice la Guía de corte Para ajustarInstalar EL Conjunto DE Hendedor Y Protector Fig Para Instalar LA Hoja DE LA SierraInstalación Y Ajuste DE LA Placa Para Ranuras FIG Ajuste LA Escala DE Biselado FIGInstale LA Cubierta DEL Motor FIG Nivele LA Sierra FIGFuncionamiento de la guía de corte longitudinal Interruptor de encendido/ apagado FigHojas para sierras FuncionamientoCorte longitudinal Cortes longitudinales en biselCortes longitudinales de piezas pequeñas Cortes transversalesCortes transversales en bisel Cortes a ingleteCortes a inglete compuestos Corte de ranurasLimpieza Colector de polvoMantenimiento Lubrique la cabeza de guía Mantenimiento del sistema de guíaAccesorios ReparacionesPóliza de Garantía Garantía limitada de tres añosDetección de problemas Manivelas DE Altura O QUÉ Hacer Biselado Difíciles DE Girar Polvo Colector QUÉ Hacer Obstrucciones

DW746 specifications

The Epson DW746 is a powerful and versatile all-in-one printer designed for business and professional use. Known for its reliability and high-quality output, the DW746 caters to a wide range of printing needs, making it an ideal choice for offices and small workgroups.

One of the main features of the DW746 is its fast printing speed. It can produce up to 25 pages per minute for monochrome documents and approximately 12 pages per minute for color prints. This efficiency ensures that users can handle large workloads without experiencing frustrating delays.

In addition to speed, the Epson DW746 offers exceptional print quality. With a maximum print resolution of 4800 x 1200 dpi, it delivers sharp text and vibrant colors. This makes it suitable for a variety of printing tasks, from professional documents to marketing materials and high-quality photos.

The DW746 utilizes PrecisionCore technology, which is a key aspect of Epson's printing process. This technology employs an array of micro-fine nozzles to create extremely precise dots of ink, resulting in superior print quality and consistency. PrecisionCore also enhances the printer's durability and longevity, ensuring that it remains a reliable workhorse for years to come.

Another notable feature is the DW746's connectivity options. It supports a variety of connectivity methods, including USB, Ethernet, and Wi-Fi, allowing users to print directly from their computers, mobile devices, or even cloud services. This flexibility makes it easy to integrate the printer into any office setup, promoting seamless workflow and collaboration.

The printer is equipped with an automatic duplex printing feature, which allows for double-sided printing. This not only saves paper but also helps businesses to reduce their overall printing costs and environmental impact.

Additionally, the Epson DW746 has a robust paper handling capacity. It comes with a standard paper tray that can hold up to 250 sheets, along with a rear manual feed slot for specialty media. For larger print jobs, users can also equip the printer with optional paper trays to increase storage capacity.

In conclusion, the Epson DW746 stands out as a powerful all-in-one solution for businesses seeking speed, quality, and versatility. With advanced printing technologies, robust connectivity options, and efficient paper handling capabilities, it meets the demands of modern office environments while delivering impressive results.