Epson DW746 Attach the Left & Right Side Support Tables FIG, Adjusting Fence to Table TOP FIG

Page 9

ATTACH THE LEFT & RIGHT SIDE SUPPORT TABLES (FIG. 8)

You will need:

6

– 10 x 25 mm Hex Head Bolts

 

6

– 10 mm Flat Washers

 

6

– 10 mm Lock Washers

ASSEMBLE THE FENCE BEAM TO THE FENCE HEAD

FIG. 10

G

(FIG. 10).

 

 

1. Remove the three flat head screws (HH) securing the

 

 

cover plate (JJ) to the fence beam with the T50 Torx

 

 

1.Install the three bolts, flat washers and lock washers in the holes in the side of the table top (B) as shown. Keep a 1/4" (6.4 mm) gap between the table top and bolt heads.

2.Slide the side support table (V) on the bolts, fitting into the notches (FF). Do tighten nuts.

3.Use the fence face as a guide to flush the support table to the main table edge and snug the front bolt. Repeat this process for the rear bolt. Tighten the cen- ter bolt.

4.Repeat on the other side.

FIG. 8

V

FF

wrench.

English

2. Turn the rip fence (G) upside down. Slide the fence

beam (H) into the rip fence as shown.

 

3. Flip the fence beam over and install the cover plate

H

and three screws. Tighten snug, do not overtighten.

 

B ADJUSTING FENCE TO TABLE TOP (FIG. 11)

JJ

IMPORTANT: Check alignment of beam and fence face

before each cutting session.

HH

ALIGNING THE RIP FENCE

 

1. Place the fence face (F) on the FIG. 11

KK

front rail (Q) and rear rail (A)

F

 

close to the miter slot (W) at

 

the right-hand side of the

 

table.

HH

2. Loosen the three locking knobs

ATTACH FRONT AND REAR RAILS TO SUPPORT TABLES (FIG. 9)

You will need for front rail:

2 – 10 x 30 mm Flat Head Screws

2 – 10 mm Flat Washers

2 – 10 mm Lock Washers

2 – 10 mm Nuts You will need for rear rail:

(KK). Allow the fence face to

 

rest on the table top, then tight-

 

en the locking knobs (KK).

W

3. Slightly loosen the three screws

 

(HH).

4. Slide the fence and adjust the beam angle until the fence face is in line with the miter

2 – 10 x 25 mm Hex Head Bolts

slot (W).

Q

 

2 – 10 mm Flat Washers

 

 

2 – 10 mm Lock Washers

 

 

2 – 10 mm Nuts

 

1.

Align front rail brackets (CC) with the side

FIG. 9

 

support table (V) and tighten bracket nuts

 

CC

 

(GG) to the rail.

 

2.

Attach the support table to the outer front

 

 

rail brackets with the screws, flat washers,

 

 

lockwashers and nuts. Keep the washers

 

 

and nut on the inside of the table.

 

3.

Attach the support table to the outer

 

 

rear rails with the bolts, flat washers,

 

 

lockwashers and nuts, Keep the washers

 

 

and nut on the inside of the table.

 

4.

Using the fence face as a straight edge

 

 

make sure the support table is level with

GG

 

or slightly below the table top. Adjust if

 

needed and tighten all fasteners.

 

5.

Repeat this procedure for the other sup-

 

 

port table.

 

5.Lock the fence beam (H) in place by pushing the rail lock-

ing lever (I) down.

6.

Tighten the locking knobs (KK),

 

I

 

starting with the rearmost two.

 

 

ADJUSTING THE FENCE FACE

 

 

(FIG. 12)

FIG.12

F

1.

Loosen the locking knobs (KK).

KK

 

2. Set the fence face (F) so it clears the table top (B) by approx. 1/16"

(1.6 mm).

3. If desired, adjust the fence face for- ward or backward.

4. Tighten the locking knobs (KK). NOTE: For very thin workpieces, the fence face can be set so it rests on the table top. Make sure to set the fence face so it clears the table top by approxi- mately. 1/16" (1.6 mm) before moving B the fence.

7

Image 9
Contents Dewalt Page General Safety Rules Definitions Safety GuidelinesVolt, Single-Phase Operation Grounding InstructionsAdditional Safety Rules for Table Saws Important Safety InstructionsPolarized Plugs Minimum Gauge for Cord SetsSAW Blade Guard and Spreader Making a Push Stick Inside Back CoverKickbacks For Future USE Hardware Included with the DW746 Woodworker’s Table SawFeatures Fig SpecificationsDW746 Basic Unit Tools IncludedUnpacking AssemblyAdjusting the Fence Face Adjusting Fence to Table TOP FIGAttach the Left & Right Side Support Tables FIG Assemble the Fence Beam to the Fence HeadTo Install the SAW Blade To adjustInstall and Adjust the Throat Plate FIG Adjust the Fence Scale Indicator FIGRip Fence Operation Saw Blades On-Off Switch FigOperation CuttingRipping Small Pieces Bevel RippingCrosscutting Bevel CrosscuttingMaintenance CleaningDust Collection Three Year Limited Warranty AccessoriesLubricating Fence Head Maintaining Fence SystemTroubleshooting Règles de sécurité générales Définitions lignes directrices en Matière de sécuritéConserver CES Directives Directives relatives à la mise à la terreDirectives de sécurité importantes Double isolationFiches Polarisées Calibre Minimum Pour RallongeFrançais Conserver CES Directives Pour UN Usage Ultérieur PROTÈGE-LAME ET Couteau SéparateurEffets DE Rebond Outils compris Appareil de base DW746Outils à fournir Quincaillerie nécessaireCaractéristiques fig Installer LA Manivelle DE BISEAU. FIGDésemballage AssemblageIl vous faut les articles suivants Assembler LA Barre DE Guidage Avant ET LES Supports FIGConsulter les Directives Fixer LES Tables DE Soutien Gauche ET Droite FIGAlignement DU Guide DE Sciage EN Long Réglage DU Guide Avec LE Dessus DE Table FIGRégler LA Face DU Guide FIG Assembler LA Poutre DU Guide À LA Tête DU Guide FIGPour effectuer le réglage, procéder comme suit Pour Installer LA Lame DE ScieInstaller LE Couvercle DU Moteur FIG Installer ET Régler LA Plaque DE Lumière FIGRégler L’ÉCHELLE DE Biseau FIG Mettre LA Scie AU Niveau FIGInterrupteur Marche/Arrêt Fig Fonctionnement du guide longitudinalLames de scie FonctionnementSciage sur le long en biseau Sciage en longSciage en long de petites pièces TronçonnageDécoupe à l’onglet Tronçonnage en biseauCoupe à rainure DépoussiérageNettoyage EntretienLubrification de la tête du guide Maintien du système du guideRéparations AccessoiresGarantie limitée trois ans DépannageCoupes D’ONGLET Imprécises Mesures À Prendre LA Machine Vibre DE Manière Mesures À Prendre ExcessiveCoincement DU Matériau Durant LA Mesures À Prendre Coupe Coupes DE Sciage EN Long Mesures À Prendre ImprécisesInstrucciones de seguridad importantes Definiciones Normas de seguridadConserve Estas Instrucciones Instrucciones de conexión a tierraDoble aislamiento Enchufes PolarizadosCalibre Mínimo Para LOS Juegos DE Cables Normas de seguridad adicionales para las sierras de banco Protector DE LA Hoja Y Hendedor Varas DE Empuje Cara Interna de la ContratapaRetrocesos Unidad básica DW746 EspecificacionesHerramientas incluidas Artículos de ferretería necesariosDesembalaje Características FigEnsamblaje Instale LA Manivela DE Biselado FIGSujete EL Riel Trasero a LA Parte Superior DEL Banco FIG Ensamble EL Riel Delantero Y LAS Abrazaderas FIGAjuste LA Guía a LA Parte Superior DEL Banco FIG Ajuste LA Cara DE LA Guía FIGEnsamble LA Barra DE LA Guía a LA Cabeza DE LA Guía FIG Para ajustar Deslice la Guía de corteInstalar EL Conjunto DE Hendedor Y Protector Fig Para Instalar LA Hoja DE LA SierraAjuste LA Escala DE Biselado FIG Instalación Y Ajuste DE LA Placa Para Ranuras FIGInstale LA Cubierta DEL Motor FIG Nivele LA Sierra FIGInterruptor de encendido/ apagado Fig Funcionamiento de la guía de corte longitudinalHojas para sierras FuncionamientoCortes longitudinales en bisel Corte longitudinalCortes longitudinales de piezas pequeñas Cortes transversalesCortes a inglete Cortes transversales en biselCortes a inglete compuestos Corte de ranurasColector de polvo MantenimientoLimpieza Mantenimiento del sistema de guía Lubrique la cabeza de guíaAccesorios ReparacionesGarantía limitada de tres años Póliza de GarantíaDetección de problemas Polvo Colector QUÉ Hacer Obstrucciones Manivelas DE Altura O QUÉ Hacer Biselado Difíciles DE Girar

DW746 specifications

The Epson DW746 is a powerful and versatile all-in-one printer designed for business and professional use. Known for its reliability and high-quality output, the DW746 caters to a wide range of printing needs, making it an ideal choice for offices and small workgroups.

One of the main features of the DW746 is its fast printing speed. It can produce up to 25 pages per minute for monochrome documents and approximately 12 pages per minute for color prints. This efficiency ensures that users can handle large workloads without experiencing frustrating delays.

In addition to speed, the Epson DW746 offers exceptional print quality. With a maximum print resolution of 4800 x 1200 dpi, it delivers sharp text and vibrant colors. This makes it suitable for a variety of printing tasks, from professional documents to marketing materials and high-quality photos.

The DW746 utilizes PrecisionCore technology, which is a key aspect of Epson's printing process. This technology employs an array of micro-fine nozzles to create extremely precise dots of ink, resulting in superior print quality and consistency. PrecisionCore also enhances the printer's durability and longevity, ensuring that it remains a reliable workhorse for years to come.

Another notable feature is the DW746's connectivity options. It supports a variety of connectivity methods, including USB, Ethernet, and Wi-Fi, allowing users to print directly from their computers, mobile devices, or even cloud services. This flexibility makes it easy to integrate the printer into any office setup, promoting seamless workflow and collaboration.

The printer is equipped with an automatic duplex printing feature, which allows for double-sided printing. This not only saves paper but also helps businesses to reduce their overall printing costs and environmental impact.

Additionally, the Epson DW746 has a robust paper handling capacity. It comes with a standard paper tray that can hold up to 250 sheets, along with a rear manual feed slot for specialty media. For larger print jobs, users can also equip the printer with optional paper trays to increase storage capacity.

In conclusion, the Epson DW746 stands out as a powerful all-in-one solution for businesses seeking speed, quality, and versatility. With advanced printing technologies, robust connectivity options, and efficient paper handling capabilities, it meets the demands of modern office environments while delivering impressive results.