Grizzly MODEL G0765 owner manual Lifting & Placing, Assembly, Power Connection, Connecting Power

Page 22

Lifting & Placing

HEAVY LIFT!

Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from another person.

With the help of another person, lift the machine to a suitable location.

Assembly

With the exception of the handwheel handles, the lathe is shipped fully assembled.

Thread the handles into the cross slide handwheel and carriage handwheel, (see Figure 14).

Cross Slide

Handwheel

Carriage

Handle

Figure 14. Handwheel handles installed.

-20-

Power Connection

Before the machine can be connected to the power source, all previous setup instructions in this manual must be completed to ensure that the machine has been assembled and installed properly.

Connecting Power

Always make sure the spindle dial on the head- stock is turned to "0" (rotated fully counterclock- wise) before connecting power.

Insert the power cord plug into a matching power supply receptacle.

Disconnecting Power

If you need to disconnect the machine from power for maintenance, service, or adjustments, turn the machine OFF and pull the plug completely out of the receptacle.

Model G0765 (Mfd. Since 12/13)

Image 22

Contents Model G0765 14 Benchtop Lathe Page Table of Contents Service Control Panel WiringMachine Description Manual Accuracy IntroductionContact Info Identification Control Panel Controls ComponentsCarriage Tailstock Rear Controls End GearsMachine Data Sheet Tailstock Info Features Safety Safety Instructions for MachineryPage Additional Safety for Metal Lathes Additional Chuck Safety Full-Load Current Rating Power SupplyAvailability 110V Circuit RequirementsMinimum Gauge Size 14 AWG Grounding & Plug RequirementsExtension Cords 50 ftPreparation SetupNeeded for Setup UnpackingInventory Installed Components Figure QtyPackaged Components Figures Qty Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Connecting Power AssemblyPower Connection Disconnecting PowerTest Run Disengaged Factory adjustments that should be verified Recommended AdjustmentsSpindle Break-In Operations Operation OverviewInstallation Removal Device Chuck & Faceplate MountingTo install the chuck Chuck InstallationTools Needed Qty Scroll Chuck Clamping Changing Jaw SetTo change the jaw set Faceplate To mount a non-concentric workpiece to the faceplateTailstock Quill Specs Using QuillTailstock Positioning TailstockTo install tooling in the tailstock Installing ToolingOffsetting Tailstock Removing ToolingItems Needed Qty Aligning Tailstock to Spindle CenterlineTo offset the tailstock To align the tailstock to the spindle centerlinePage Mounting Dead Center in Spindle CentersDead Centers Removing Center from SpindleMounting Workpiece Between Centers Mounting Center in TailstockRemoving Center from Tailstock To mount a center in the tailstockTo install and use the steady rest Tools Needed for Installation/Removal QtySteady Rest Installing Tool Compound Rest Four-Way Tool PostTo align cutting tool with tailstock center Aligning Cutting Tool with Spindle CenterlineBelow are two common methods Top ViewManual Feed Spindle SpeedConfiguration Example Setting Spindle Speed RangeSetting Spindle Direction & Speed To set spindle speed to 100 RPMPower Feed Power Feed ControlsSetting Power Feed Rate To set power feed for 0.04 in./revSecondary Threading Configuration Primary Threading ConfigurationPower Feed Configuration End GearsTo configure end gears for threading 20 TPI End Gear Configuration Example40T 65T Gear 50 T Ge ar 20 TPI Page To set the lathe to thread 20 TPI ThreadingHeadstock Threading Controls Feed Direction LeverApron Threading Controls Thread Dial ChartThread Dial Dial Number Thread Dial Accessories D3640-Shop Fox Tool Table PlusCleaning/Protecting MaintenanceSchedule Lubrication Frequency LubricationBall Oilers Bedways Leadscrew & Carriage RackCross Slide & Compound Slide Tumbler Gears Machine StorageChange Gear Bushing Preparing Lathe for StorageTroubleshooting ServiceSymptom Possible Cause Possible Solution Lathe Operation Cross Slide Backlash AdjustmentLeadscrew End-Play Adjustment To remove leadscrew end playGib Adjustment To adjust cross slide and compound slide gibsTo adjust half nut Half Nut AdjustmentFuse Replacement To replace fuseBrush Replacement To replace motor brushesTiming Belt Tension Replacement Tensioning Timing BeltReplacing Timing Belt Wiring Wiring Safety InstructionsControl Panel Wiring Machine FrameControl Panel Wiring Photos G0765 wiring overviewMotor/Speed Sensor/ Plug Wiring 110 VACMain Description Description Labels & Cosmetics Front 255 254 256 257 259 258 253 252 261 251 260Threading Charts AppendixWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns