Grizzly MODEL G0765 owner manual Replacing Timing Belt

Page 63

Replacing Timing Belt

1.DISCONNECT LATHE FROM POWER!

2.Remove end cover, rear motor cover, and electrical cabinet.

Side

Gear

Sensor

Cover

 

Wheel

 

 

Outer

 

Inner

 

Spanner

Spanner

 

 

Nut

Nut

 

 

 

 

 

Speed

 

 

Sensor

Figure 91. Components to be removed to

replace timing belt.

3.Using a fine-tip felt marker, place alignment marks on inner spanner nut and gear shown in Figure 91. The purpose or these marks is to help re-install the outer spanner nut.

4.Carefully remove outer spanner nut, speed sensor, and sensor wheel.

5.Remove side cover assembly.

6.Loosen motor mount hex nuts shown in Figure 92.

Motor

Mount

Hex Nuts

7.Slide off old timing belt and install the new one, making sure that belt teeth are seated together with pulley teeth (see Figure 93).

Timing

Belt

Figure 93. Timing belt installed.

8.Tension timing belt. (Refer to Tensioning Timing Belt on Page 60 for detailed instruc- tions.)

9.Check alignment marks you made on inner spanner nut and gear in Step 3. The marks should still be aligned.

—If marks are not aligned, adjust inner span- ner nut as needed to align them.

10.Re-install side cover, sensor wheel, speed sensor, and outer spanner nut.

11.Re-install electrical cabinet, rear motor cover, and end cover.

Figure 92. Location of motor mount hex nuts.

Model G0765 (Mfd. Since 12/13)

-61-

Image 63
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Control Panel Wiring ServiceIntroduction Machine Description Manual AccuracyContact Info Identification Controls Components Control PanelCarriage End Gears Tailstock Rear ControlsMachine Data Sheet Tailstock Info Features Safety Instructions for Machinery SafetyPage Additional Safety for Metal Lathes Additional Chuck Safety 110V Circuit Requirements Power SupplyAvailability Full-Load Current Rating50 ft Grounding & Plug RequirementsExtension Cords Minimum Gauge Size 14 AWGUnpacking SetupNeeded for Setup PreparationInstalled Components Figure Qty InventoryPackaged Components Figures Qty Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Disconnecting Power AssemblyPower Connection Connecting PowerTest Run Disengaged Recommended Adjustments Factory adjustments that should be verifiedSpindle Break-In Operation Overview OperationsChuck & Faceplate Mounting Installation Removal DeviceChuck Installation To install the chuckTools Needed Qty Changing Jaw Set Scroll Chuck ClampingTo change the jaw set To mount a non-concentric workpiece to the faceplate FaceplatePositioning Tailstock Using QuillTailstock Tailstock Quill SpecsRemoving Tooling Installing ToolingOffsetting Tailstock To install tooling in the tailstockTo align the tailstock to the spindle centerline Aligning Tailstock to Spindle CenterlineTo offset the tailstock Items Needed QtyPage Removing Center from Spindle CentersDead Centers Mounting Dead Center in SpindleTo mount a center in the tailstock Mounting Center in TailstockRemoving Center from Tailstock Mounting Workpiece Between CentersTools Needed for Installation/Removal Qty To install and use the steady restSteady Rest Compound Rest Four-Way Tool Post Installing ToolTop View Aligning Cutting Tool with Spindle CenterlineBelow are two common methods To align cutting tool with tailstock centerSpindle Speed Manual FeedTo set spindle speed to 100 RPM Setting Spindle Speed RangeSetting Spindle Direction & Speed Configuration ExamplePower Feed Controls Power FeedTo set power feed for 0.04 in./rev Setting Power Feed RateEnd Gears Primary Threading ConfigurationPower Feed Configuration Secondary Threading ConfigurationEnd Gear Configuration Example To configure end gears for threading 20 TPI40T 65T Gear 50 T Ge ar 20 TPI Page Feed Direction Lever ThreadingHeadstock Threading Controls To set the lathe to thread 20 TPIThread Dial Chart Apron Threading ControlsThread Dial Dial Number Thread Dial D3640-Shop Fox Tool Table Plus AccessoriesMaintenance Cleaning/ProtectingSchedule Lubrication Lubrication FrequencyBall Oilers Leadscrew & Carriage Rack BedwaysCross Slide & Compound Slide Preparing Lathe for Storage Machine StorageChange Gear Bushing Tumbler GearsService TroubleshootingSymptom Possible Cause Possible Solution Lathe Operation To remove leadscrew end play Backlash AdjustmentLeadscrew End-Play Adjustment Cross SlideTo adjust cross slide and compound slide gibs Gib AdjustmentTo replace fuse Half Nut AdjustmentFuse Replacement To adjust half nutTo replace motor brushes Brush ReplacementTensioning Timing Belt Timing Belt Tension ReplacementReplacing Timing Belt Wiring Safety Instructions WiringMachine Frame Control Panel WiringG0765 wiring overview Control Panel Wiring Photos110 VAC Motor/Speed Sensor/ Plug WiringMain Description Description 255 254 256 257 259 258 253 252 261 251 260 Labels & Cosmetics FrontAppendix Threading ChartsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty & Returns