Grizzly MODEL G0765 owner manual Accessories, D3640-Shop Fox Tool Table Plus

Page 51

SECTION 5: ACCESSORIES

Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly.

NOTICE

Refer to our website or latest catalog for additional recommended accessories.

H2987—½" Bent Lathe Dog

H2988—1" Bent Lathe Dog

H2989—1½" Bent Lathe Dog

H2990—2" Bent Lathe Dog

H2991—3" Bent Lathe Dog

T25206—11 Pc. Carbide Bit Set 5⁄16"

This 11-Pc. Carbide-Tipped Tool Bit Set includes a wide variety of tool types for just about any machining operation. This set also includes two boring bars. Boring bars measure 47⁄8" long. Shank size for all is 5⁄16".

Figure 72. 11-Pc. Carbide-Tipped Tool Set.

D3640—Shop Fox Tool Table Plus

This new, tool table plus was designed to answer customer requests for a slightly wider and taller table than our D2056 to accommodate a variety of bench-top machines.

Figure 73. D3640 Shop Fox Tool Table Plus.

SB1365—South Bend Way Oil for Lathes Engineered for the high pressure exerted on horizontal or vertical ways and slides. Protects against rust and corrosion. Ensures stick-free, smooth motion which maximizes finishes and extends the life of your machine. Won’t gum up! 12 oz. AMGA#2 (ISO 68 Equivalent).

Figure 74. Way Oil.

order online at www.grizzly.com or call 1-800-523-4777

Model G0765 (Mfd. Since 12/13)

-49-

Image 51

Contents Model G0765 14 Benchtop Lathe Page Table of Contents Control Panel Wiring ServiceIntroduction Machine Description Manual AccuracyContact Info Identification Controls Components Control PanelCarriage End Gears Tailstock Rear ControlsMachine Data Sheet Tailstock Info Features Safety Instructions for Machinery SafetyPage Additional Safety for Metal Lathes Additional Chuck Safety 110V Circuit Requirements Power SupplyAvailability Full-Load Current Rating50 ft Grounding & Plug RequirementsExtension Cords Minimum Gauge Size 14 AWGUnpacking SetupNeeded for Setup PreparationInstalled Components Figure Qty InventoryPackaged Components Figures Qty Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Disconnecting Power AssemblyPower Connection Connecting PowerTest Run Disengaged Recommended Adjustments Factory adjustments that should be verifiedSpindle Break-In Operation Overview OperationsChuck & Faceplate Mounting Installation Removal DeviceChuck Installation To install the chuckTools Needed Qty Changing Jaw Set Scroll Chuck ClampingTo change the jaw set To mount a non-concentric workpiece to the faceplate FaceplatePositioning Tailstock Using QuillTailstock Tailstock Quill SpecsRemoving Tooling Installing ToolingOffsetting Tailstock To install tooling in the tailstockTo align the tailstock to the spindle centerline Aligning Tailstock to Spindle CenterlineTo offset the tailstock Items Needed QtyPage Removing Center from Spindle CentersDead Centers Mounting Dead Center in SpindleTo mount a center in the tailstock Mounting Center in TailstockRemoving Center from Tailstock Mounting Workpiece Between CentersTools Needed for Installation/Removal Qty To install and use the steady restSteady Rest Compound Rest Four-Way Tool Post Installing ToolTop View Aligning Cutting Tool with Spindle CenterlineBelow are two common methods To align cutting tool with tailstock centerSpindle Speed Manual FeedTo set spindle speed to 100 RPM Setting Spindle Speed RangeSetting Spindle Direction & Speed Configuration ExamplePower Feed Controls Power FeedTo set power feed for 0.04 in./rev Setting Power Feed RateEnd Gears Primary Threading ConfigurationPower Feed Configuration Secondary Threading ConfigurationEnd Gear Configuration Example To configure end gears for threading 20 TPI40T 65T Gear 50 T Ge ar 20 TPI Page Feed Direction Lever ThreadingHeadstock Threading Controls To set the lathe to thread 20 TPIThread Dial Chart Apron Threading ControlsThread Dial Dial Number Thread Dial D3640-Shop Fox Tool Table Plus AccessoriesMaintenance Cleaning/ProtectingSchedule Lubrication Lubrication FrequencyBall Oilers Leadscrew & Carriage Rack BedwaysCross Slide & Compound Slide Preparing Lathe for Storage Machine StorageChange Gear Bushing Tumbler GearsService TroubleshootingSymptom Possible Cause Possible Solution Lathe Operation To remove leadscrew end play Backlash AdjustmentLeadscrew End-Play Adjustment Cross SlideTo adjust cross slide and compound slide gibs Gib AdjustmentTo replace fuse Half Nut AdjustmentFuse Replacement To adjust half nutTo replace motor brushes Brush ReplacementTensioning Timing Belt Timing Belt Tension ReplacementReplacing Timing Belt Wiring Safety Instructions WiringMachine Frame Control Panel WiringG0765 wiring overview Control Panel Wiring Photos110 VAC Motor/Speed Sensor/ Plug WiringMain Description Description 255 254 256 257 259 258 253 252 261 251 260 Labels & Cosmetics FrontAppendix Threading ChartsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty & Returns