Grizzly MODEL G0765 End Gears, Primary Threading Configuration, Power Feed Configuration

Page 45

End Gears

The end gears must be correctly setup for power feed and threading. Use the photo below to identify the A, B, C, and D change gears, which are also referenced on the headstock feed rate gear chart.

Primary Threading Configuration

This threading configuration is used for inch and metric threading. Mesh the A, B, and D gears, as shown in Figure 56. The C gear does not mesh with any other gears in this configuration, so it is not important which gear is installed in the C posi- tion. The B and C gears share a keyed bushing.

A

B

C

D

A

B

C

D

A

Gear

B

Gear

C

Gear

D

Gear

Figure 54. Change gear identification.

The following subsections explain how to config- ure the end gears, which are accessed by remov- ing the end cover.

Power Feed Configuration

The end gears are preset by the factory in this configuration, which is only used for power feed- ing. Mesh the top 20T A gear with the 80T B gear,

Figure 56. Primary threading configuration.

Secondary Threading Configuration

This threading configuration is used for a different range of threads and feed rates than the primary threading configuration. Mesh the A and B gears, and mesh the C and D gears, as shown in Figure 57. The B and C gears share a keyed bushing.

and mesh the 20T C gear with the 80T D gear (see Figure 55).

A

A Gear

A(20T)

B(80T)

C(20T)

D (80T)

A Gear

B Gear

(20T)

(80T)

C Gear

 

(20T)

 

B

C

D

B

Gear

C

 

D

Gear

 

Gear

 

 

 

D Gear

(80T)

Figure 57. Secondary threading configuration.

Figure 55. Power feed end gear configuration.

Model G0765 (Mfd. Since 12/13)

-43-

Image 45
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Control Panel Wiring ServiceIntroduction Machine Description Manual AccuracyContact Info Identification Controls Components Control PanelCarriage End Gears Tailstock Rear ControlsMachine Data Sheet Tailstock Info Features Safety Instructions for Machinery SafetyPage Additional Safety for Metal Lathes Additional Chuck Safety Availability Power SupplyFull-Load Current Rating 110V Circuit RequirementsExtension Cords Grounding & Plug RequirementsMinimum Gauge Size 14 AWG 50 ftNeeded for Setup SetupPreparation UnpackingInstalled Components Figure Qty InventoryPackaged Components Figures Qty Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Power Connection AssemblyConnecting Power Disconnecting PowerTest Run Disengaged Recommended Adjustments Factory adjustments that should be verifiedSpindle Break-In Operation Overview OperationsChuck & Faceplate Mounting Installation Removal DeviceChuck Installation To install the chuckTools Needed Qty Changing Jaw Set Scroll Chuck ClampingTo change the jaw set To mount a non-concentric workpiece to the faceplate FaceplateTailstock Using QuillTailstock Quill Specs Positioning TailstockOffsetting Tailstock Installing ToolingTo install tooling in the tailstock Removing ToolingTo offset the tailstock Aligning Tailstock to Spindle CenterlineItems Needed Qty To align the tailstock to the spindle centerlinePage Dead Centers CentersMounting Dead Center in Spindle Removing Center from SpindleRemoving Center from Tailstock Mounting Center in TailstockMounting Workpiece Between Centers To mount a center in the tailstockTools Needed for Installation/Removal Qty To install and use the steady restSteady Rest Compound Rest Four-Way Tool Post Installing ToolBelow are two common methods Aligning Cutting Tool with Spindle CenterlineTo align cutting tool with tailstock center Top ViewSpindle Speed Manual FeedSetting Spindle Direction & Speed Setting Spindle Speed RangeConfiguration Example To set spindle speed to 100 RPMPower Feed Controls Power FeedTo set power feed for 0.04 in./rev Setting Power Feed RatePower Feed Configuration Primary Threading ConfigurationSecondary Threading Configuration End GearsEnd Gear Configuration Example To configure end gears for threading 20 TPI40T 65T Gear 50 T Ge ar 20 TPI Page Headstock Threading Controls ThreadingTo set the lathe to thread 20 TPI Feed Direction LeverThread Dial Chart Apron Threading ControlsThread Dial Dial Number Thread Dial D3640-Shop Fox Tool Table Plus AccessoriesMaintenance Cleaning/ProtectingSchedule Lubrication Lubrication FrequencyBall Oilers Leadscrew & Carriage Rack BedwaysCross Slide & Compound Slide Change Gear Bushing Machine StorageTumbler Gears Preparing Lathe for StorageService TroubleshootingSymptom Possible Cause Possible Solution Lathe Operation Leadscrew End-Play Adjustment Backlash AdjustmentCross Slide To remove leadscrew end playTo adjust cross slide and compound slide gibs Gib AdjustmentFuse Replacement Half Nut AdjustmentTo adjust half nut To replace fuseTo replace motor brushes Brush ReplacementTensioning Timing Belt Timing Belt Tension ReplacementReplacing Timing Belt Wiring Safety Instructions WiringMachine Frame Control Panel WiringG0765 wiring overview Control Panel Wiring Photos110 VAC Motor/Speed Sensor/ Plug WiringMain Description Description 255 254 256 257 259 258 253 252 261 251 260 Labels & Cosmetics FrontAppendix Threading ChartsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty & Returns