Grizzly MODEL G0765 Aligning Cutting Tool with Spindle Centerline, Below are two common methods

Page 40

Aligning Cutting Tool with Spindle Centerline

For most operations, the cutting tool tip should be aligned with the spindle centerline, as illustrated below.

Cutting

Spindle

Tool

Center

 

Line

Figure 43. Cutting tool aligned with spindle

centerline (viewed from tailstock).

There are a number of ways to check and align the cutting tool to the spindle centerline. If nec- essary, you can raise the cutting tool by placing steel shims underneath it. The shims should be as long and as wide as the cutting tool to properly support it.

Below are two common methods:

Move the tailstock center over the cross slide and use a fine ruler to measure the distance from the surface of the cross slide to the tip of the center. Adjust the cutting tool height so it is the same distance above the cross slide as the tailstock center.

Align the tip of the cutting tool with a tailstock center, as instructed in the following pro- cedure. For this to work, the tailstock must be aligned to the spindle centerline (refer to

Aligning Tailstock To Spindle Centerline in this manual for detailed instructions).

Tools Needed

Qty

Hex Wrench 6mm.

............................................. 1

Steel Shims

As Needed

Cutting Tool

1

Tailstock Center

1

To align cutting tool with tailstock center:

1.Mount cutting tool in tool post, then secure post so tool faces tailstock.

2.Install a center in tailstock, and position the center tip near cutting tool tip.

3.Lock tailstock and quill in place.

4.Adjust height of cutting tool so tool tip is aligned vertically with center tip, as illustrated below.

(Top View)

 

Tailstock

Cutting

Center

 

Tool

 

Cutting

Tailstock

Tool

Center

 

(Side View)

Figure 44. Cutting tool aligned to the tailstock

center.

-38-

Model G0765 (Mfd. Since 12/13)

Image 40
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Service Control Panel WiringMachine Description Manual Accuracy IntroductionContact Info Identification Control Panel Controls ComponentsCarriage Tailstock Rear Controls End GearsMachine Data Sheet Tailstock Info Features Safety Safety Instructions for MachineryPage Additional Safety for Metal Lathes Additional Chuck Safety Power Supply AvailabilityFull-Load Current Rating 110V Circuit RequirementsGrounding & Plug Requirements Extension CordsMinimum Gauge Size 14 AWG 50 ftSetup Needed for SetupPreparation UnpackingInventory Installed Components Figure QtyPackaged Components Figures Qty Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Assembly Power ConnectionConnecting Power Disconnecting PowerTest Run Disengaged Factory adjustments that should be verified Recommended AdjustmentsSpindle Break-In Operations Operation OverviewInstallation Removal Device Chuck & Faceplate MountingTo install the chuck Chuck InstallationTools Needed Qty Scroll Chuck Clamping Changing Jaw SetTo change the jaw set Faceplate To mount a non-concentric workpiece to the faceplateUsing Quill TailstockTailstock Quill Specs Positioning TailstockInstalling Tooling Offsetting TailstockTo install tooling in the tailstock Removing ToolingAligning Tailstock to Spindle Centerline To offset the tailstockItems Needed Qty To align the tailstock to the spindle centerlinePage Centers Dead CentersMounting Dead Center in Spindle Removing Center from SpindleMounting Center in Tailstock Removing Center from TailstockMounting Workpiece Between Centers To mount a center in the tailstockTo install and use the steady rest Tools Needed for Installation/Removal QtySteady Rest Installing Tool Compound Rest Four-Way Tool PostAligning Cutting Tool with Spindle Centerline Below are two common methodsTo align cutting tool with tailstock center Top ViewManual Feed Spindle SpeedSetting Spindle Speed Range Setting Spindle Direction & SpeedConfiguration Example To set spindle speed to 100 RPMPower Feed Power Feed ControlsSetting Power Feed Rate To set power feed for 0.04 in./revPrimary Threading Configuration Power Feed ConfigurationSecondary Threading Configuration End GearsTo configure end gears for threading 20 TPI End Gear Configuration Example40T 65T Gear 50 T Ge ar 20 TPI Page Threading Headstock Threading ControlsTo set the lathe to thread 20 TPI Feed Direction LeverApron Threading Controls Thread Dial ChartThread Dial Dial Number Thread Dial Accessories D3640-Shop Fox Tool Table PlusCleaning/Protecting MaintenanceSchedule Lubrication Frequency LubricationBall Oilers Bedways Leadscrew & Carriage RackCross Slide & Compound Slide Machine Storage Change Gear BushingTumbler Gears Preparing Lathe for StorageTroubleshooting ServiceSymptom Possible Cause Possible Solution Lathe Operation Backlash Adjustment Leadscrew End-Play AdjustmentCross Slide To remove leadscrew end playGib Adjustment To adjust cross slide and compound slide gibsHalf Nut Adjustment Fuse ReplacementTo adjust half nut To replace fuseBrush Replacement To replace motor brushesTiming Belt Tension Replacement Tensioning Timing BeltReplacing Timing Belt Wiring Wiring Safety InstructionsControl Panel Wiring Machine FrameControl Panel Wiring Photos G0765 wiring overviewMotor/Speed Sensor/ Plug Wiring 110 VACMain Description Description Labels & Cosmetics Front 255 254 256 257 259 258 253 252 261 251 260Threading Charts AppendixWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns