Grizzly MODEL G0765 owner manual Faceplate, To mount a non-concentric workpiece to the faceplate

Page 31

Faceplate

Refer to the prior Chuck Installation and Chuck Removal subsections for instructions on installing or removing the faceplate.

The faceplate included with your lathe can be used for a wide range of operations, including machining non-concentric workpieces, straight turning between centers, off-center turning, and boring.

The tools needed for mounting a workpiece will vary depending on the type of setup you have.

Machining non-concentric workpieces at high speeds could cause the workpiece to be thrown from the lathe with deadly force. To reduce this risk, use a low RPM, and use counter-weights to balance the faceplate or workpiece.

Failure to properly secure a workpiece to the faceplate could cause the workpiece to be thrown from the lathe with deadly force. To reduce this risk, use a minimum of THREE independent clamping devices to hold the workpiece onto the faceplate.

Model G0765 (Mfd. Since 12/13)

To mount a non-concentric workpiece to the faceplate:

1.DISCONNECT LATHE FROM POWER!

2.Use appropriate device to protect ways (refer to Installation & Removal Device subsec- tion).

3.With help from another person or holding device to support workpiece, position it onto faceplate and clamp it in place with a mini- mum of three independent clamping devices (see Figure below for an example).

Be sure to take into account rotational and cutting forces that will be applied to work- piece when clamping it to faceplate. If neces- sary, use counter-weights to balance assem- bly and use a dial indicator to make sure workpiece is properly positioned for your operation.

Non-Cylindrical

Workpiece

Clamp

Faceplate

Figure 26. Example of a workpiece clamped in a

faceplate.

-29-

Image 31
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Control Panel Wiring ServiceMachine Description Manual Accuracy IntroductionContact Info Identification Control Panel Controls ComponentsCarriage End Gears Tailstock Rear ControlsMachine Data Sheet Tailstock Info Features Safety Instructions for Machinery SafetyPage Additional Safety for Metal Lathes Additional Chuck Safety 110V Circuit Requirements Power SupplyAvailability Full-Load Current Rating50 ft Grounding & Plug RequirementsExtension Cords Minimum Gauge Size 14 AWGUnpacking SetupNeeded for Setup PreparationInventory Installed Components Figure QtyPackaged Components Figures Qty Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Disconnecting Power AssemblyPower Connection Connecting PowerTest Run Disengaged Factory adjustments that should be verified Recommended AdjustmentsSpindle Break-In Operation Overview OperationsChuck & Faceplate Mounting Installation Removal DeviceTo install the chuck Chuck InstallationTools Needed Qty Changing Jaw Set Scroll Chuck ClampingTo change the jaw set To mount a non-concentric workpiece to the faceplate FaceplatePositioning Tailstock Using QuillTailstock Tailstock Quill SpecsRemoving Tooling Installing ToolingOffsetting Tailstock To install tooling in the tailstockTo align the tailstock to the spindle centerline Aligning Tailstock to Spindle CenterlineTo offset the tailstock Items Needed QtyPage Removing Center from Spindle CentersDead Centers Mounting Dead Center in SpindleTo mount a center in the tailstock Mounting Center in TailstockRemoving Center from Tailstock Mounting Workpiece Between CentersTo install and use the steady rest Tools Needed for Installation/Removal QtySteady Rest Compound Rest Four-Way Tool Post Installing ToolTop View Aligning Cutting Tool with Spindle CenterlineBelow are two common methods To align cutting tool with tailstock centerSpindle Speed Manual FeedTo set spindle speed to 100 RPM Setting Spindle Speed RangeSetting Spindle Direction & Speed Configuration ExamplePower Feed Controls Power FeedTo set power feed for 0.04 in./rev Setting Power Feed RateEnd Gears Primary Threading ConfigurationPower Feed Configuration Secondary Threading ConfigurationTo configure end gears for threading 20 TPI End Gear Configuration Example40T 65T Gear 50 T Ge ar 20 TPI Page Feed Direction Lever ThreadingHeadstock Threading Controls To set the lathe to thread 20 TPIApron Threading Controls Thread Dial ChartThread Dial Dial Number Thread Dial D3640-Shop Fox Tool Table Plus AccessoriesCleaning/Protecting MaintenanceSchedule Lubrication Frequency LubricationBall Oilers Bedways Leadscrew & Carriage RackCross Slide & Compound Slide Preparing Lathe for Storage Machine StorageChange Gear Bushing Tumbler GearsTroubleshooting ServiceSymptom Possible Cause Possible Solution Lathe Operation To remove leadscrew end play Backlash AdjustmentLeadscrew End-Play Adjustment Cross SlideTo adjust cross slide and compound slide gibs Gib AdjustmentTo replace fuse Half Nut AdjustmentFuse Replacement To adjust half nutTo replace motor brushes Brush ReplacementTensioning Timing Belt Timing Belt Tension ReplacementReplacing Timing Belt Wiring Safety Instructions WiringMachine Frame Control Panel WiringG0765 wiring overview Control Panel Wiring Photos110 VAC Motor/Speed Sensor/ Plug WiringMain Description Description 255 254 256 257 259 258 253 252 261 251 260 Labels & Cosmetics FrontAppendix Threading ChartsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty & Returns