Grizzly MODEL G0765 owner manual Chuck Installation, Tools Needed Qty, To install the chuck

Page 28

Chuck Installation

To ensure accurate work, it is extremely important to make sure the spindle nose and chuck mating surfaces are clean. Even a small amount of lint or debris can affect accuracy.

The chuck is properly installed when it is seated against the backplate shoulder (see Figure 19 below).

Backplate

Shoulder

Mounting

Hole

Inside

 

Taper

 

Figure 19. Spindle backplate.

 

Tools Needed:

Qty

Open-End Wrench 10mm

1

To install the chuck:

 

1.DISCONNECT LATHE FROM POWER!

2.Use an appropriate device to protect ways dur- ing installation process (refer to Installation & Removal Device on Page 25).

3.Thoroughly clean and wipe-down all mating surfaces with a lightly-oiled, lint-free rag.

-26-

4.Insert chuck screws through mounting holes in spindle backplate, as shown in Figure 20. Make sure chuck seats firmly and evenly against backplate shoulder.

Intrinsic

Chuck Screw

Backplate

 

Figure 20. Inserting chuck into backplate.

5.Use a lock washer and hex nut on each chuck screw to secure chuck (see Figure 21).

Hex Nut

Lock Washer

Figure 21. Chuck secured against backplate.

Model G0765 (Mfd. Since 12/13)

Image 28
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Service Control Panel WiringMachine Description Manual Accuracy IntroductionContact Info Identification Control Panel Controls ComponentsCarriage Tailstock Rear Controls End GearsMachine Data Sheet Tailstock Info Features Safety Safety Instructions for MachineryPage Additional Safety for Metal Lathes Additional Chuck Safety Power Supply AvailabilityFull-Load Current Rating 110V Circuit RequirementsGrounding & Plug Requirements Extension CordsMinimum Gauge Size 14 AWG 50 ftSetup Needed for SetupPreparation UnpackingInventory Installed Components Figure QtyPackaged Components Figures Qty Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Assembly Power ConnectionConnecting Power Disconnecting PowerTest Run Disengaged Factory adjustments that should be verified Recommended AdjustmentsSpindle Break-In Operations Operation OverviewInstallation Removal Device Chuck & Faceplate MountingTo install the chuck Chuck InstallationTools Needed Qty Scroll Chuck Clamping Changing Jaw SetTo change the jaw set Faceplate To mount a non-concentric workpiece to the faceplateUsing Quill TailstockTailstock Quill Specs Positioning TailstockInstalling Tooling Offsetting TailstockTo install tooling in the tailstock Removing ToolingAligning Tailstock to Spindle Centerline To offset the tailstockItems Needed Qty To align the tailstock to the spindle centerlinePage Centers Dead CentersMounting Dead Center in Spindle Removing Center from SpindleMounting Center in Tailstock Removing Center from TailstockMounting Workpiece Between Centers To mount a center in the tailstockTo install and use the steady rest Tools Needed for Installation/Removal QtySteady Rest Installing Tool Compound Rest Four-Way Tool PostAligning Cutting Tool with Spindle Centerline Below are two common methodsTo align cutting tool with tailstock center Top ViewManual Feed Spindle SpeedSetting Spindle Speed Range Setting Spindle Direction & SpeedConfiguration Example To set spindle speed to 100 RPMPower Feed Power Feed ControlsSetting Power Feed Rate To set power feed for 0.04 in./revPrimary Threading Configuration Power Feed ConfigurationSecondary Threading Configuration End GearsTo configure end gears for threading 20 TPI End Gear Configuration Example40T 65T Gear 50 T Ge ar 20 TPI Page Threading Headstock Threading ControlsTo set the lathe to thread 20 TPI Feed Direction LeverApron Threading Controls Thread Dial ChartThread Dial Dial Number Thread Dial Accessories D3640-Shop Fox Tool Table PlusCleaning/Protecting MaintenanceSchedule Lubrication Frequency LubricationBall Oilers Bedways Leadscrew & Carriage RackCross Slide & Compound Slide Machine Storage Change Gear BushingTumbler Gears Preparing Lathe for StorageTroubleshooting ServiceSymptom Possible Cause Possible Solution Lathe Operation Backlash Adjustment Leadscrew End-Play AdjustmentCross Slide To remove leadscrew end playGib Adjustment To adjust cross slide and compound slide gibsHalf Nut Adjustment Fuse ReplacementTo adjust half nut To replace fuseBrush Replacement To replace motor brushesTiming Belt Tension Replacement Tensioning Timing BeltReplacing Timing Belt Wiring Wiring Safety InstructionsControl Panel Wiring Machine FrameControl Panel Wiring Photos G0765 wiring overviewMotor/Speed Sensor/ Plug Wiring 110 VACMain Description Description Labels & Cosmetics Front 255 254 256 257 259 258 253 252 261 251 260Threading Charts AppendixWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns