Grizzly MODEL G0765 owner manual Cleanup, Before cleaning, gather the following

Page 20

Cleanup

The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean.

Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.

There are many ways to remove this rust preven- tative, but the following steps work well in a wide variety of situations. Always follow the manufac- turer’s instructions with any cleaning product you use and make sure you work in a well-ventilated area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

Disposable rags

Cleaner/degreaser (WD•40 works well)

Safety glasses & disposable gloves

Plastic paint scraper (optional)

Basic steps for removing rust preventative:

1.Put on safety glasses.

2.Coat the rust preventative with a liberal amount of cleaner/degreaser, then let it soak for 5–10 minutes.

3.Wipe off the surfaces. If your cleaner/degreas- er is effective, the rust preventative will wipe off easily. If you have a plastic paint scraper, scrape off as much as you can first, then wipe off the rest with the rag.

4.Repeat Steps 2–3as necessary until clean, then coat all unpainted surfaces with a quality metal protectant to prevent rust.

-18-

Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. Avoid using these products to clean machinery.

Many cleaning solvents are toxic if inhaled. Only work in a well-ventilated area.

NOTICE

Avoid chlorine-based solvents, such as acetone or brake parts cleaner, that may damage painted surfaces.

T23692—Orange Power Degreaser

A great product for removing the waxy shipping grease from your machine during clean up.

Figure 12. T23692 Orange Power Degreaser.

Model G0765 (Mfd. Since 12/13)

Image 20
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Service Control Panel WiringContact Info IntroductionMachine Description Manual Accuracy Identification Carriage Controls ComponentsControl Panel Tailstock Rear Controls End GearsMachine Data Sheet Tailstock Info Features Safety Safety Instructions for MachineryPage Additional Safety for Metal Lathes Additional Chuck Safety Power Supply AvailabilityFull-Load Current Rating 110V Circuit RequirementsGrounding & Plug Requirements Extension CordsMinimum Gauge Size 14 AWG 50 ftSetup Needed for SetupPreparation UnpackingPackaged Components Figures Qty Installed Components Figure QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Assembly Power ConnectionConnecting Power Disconnecting PowerTest Run Disengaged Spindle Break-In Recommended AdjustmentsFactory adjustments that should be verified Operations Operation OverviewInstallation Removal Device Chuck & Faceplate MountingTools Needed Qty Chuck InstallationTo install the chuck Scroll Chuck Clamping Changing Jaw SetTo change the jaw set Faceplate To mount a non-concentric workpiece to the faceplateUsing Quill TailstockTailstock Quill Specs Positioning TailstockInstalling Tooling Offsetting TailstockTo install tooling in the tailstock Removing ToolingAligning Tailstock to Spindle Centerline To offset the tailstockItems Needed Qty To align the tailstock to the spindle centerlinePage Centers Dead CentersMounting Dead Center in Spindle Removing Center from SpindleMounting Center in Tailstock Removing Center from TailstockMounting Workpiece Between Centers To mount a center in the tailstockSteady Rest Tools Needed for Installation/Removal QtyTo install and use the steady rest Installing Tool Compound Rest Four-Way Tool PostAligning Cutting Tool with Spindle Centerline Below are two common methodsTo align cutting tool with tailstock center Top ViewManual Feed Spindle SpeedSetting Spindle Speed Range Setting Spindle Direction & SpeedConfiguration Example To set spindle speed to 100 RPMPower Feed Power Feed ControlsSetting Power Feed Rate To set power feed for 0.04 in./revPrimary Threading Configuration Power Feed ConfigurationSecondary Threading Configuration End Gears40T 65T Gear 50 T Ge ar 20 TPI End Gear Configuration ExampleTo configure end gears for threading 20 TPI Page Threading Headstock Threading ControlsTo set the lathe to thread 20 TPI Feed Direction LeverThread Dial Thread Dial ChartApron Threading Controls Dial Number Thread Dial Accessories D3640-Shop Fox Tool Table PlusSchedule MaintenanceCleaning/Protecting Ball Oilers LubricationLubrication Frequency Cross Slide & Compound Slide Leadscrew & Carriage RackBedways Machine Storage Change Gear BushingTumbler Gears Preparing Lathe for StorageSymptom Possible Cause Possible Solution ServiceTroubleshooting Lathe Operation Backlash Adjustment Leadscrew End-Play AdjustmentCross Slide To remove leadscrew end playGib Adjustment To adjust cross slide and compound slide gibsHalf Nut Adjustment Fuse ReplacementTo adjust half nut To replace fuseBrush Replacement To replace motor brushesTiming Belt Tension Replacement Tensioning Timing BeltReplacing Timing Belt Wiring Wiring Safety InstructionsControl Panel Wiring Machine FrameControl Panel Wiring Photos G0765 wiring overviewMotor/Speed Sensor/ Plug Wiring 110 VACMain Description Description Labels & Cosmetics Front 255 254 256 257 259 258 253 252 261 251 260Threading Charts AppendixWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns