Grizzly MODEL G0765 owner manual Disengaged

Page 24

4.Disengage half nut with lever shown in

Figure 17.

Thread Dial

Half Nut

Lever

Disengaged

Halfnut

Lever

Engaged

Figure 17. Half nut lever disengaged.

5.Press tab in on side of Emergency Stop button, lift switch cover, and press green ON button to reset Emergency Stop button. The spindle speed display and power button should illuminate to indicate that lathe is con- nected to power supply.

6.Verify lathe is operating correctly by turning spindle direction switch to "F" position. Slowly turn variale speed dial clockwise until spindle speed display shows 100 RPM. The spindle should rotate counterclockwise—down and toward the front of the lathe.

7.Push Emergency Stop button to turn lathe OFF. Then, without resetting Emergency Stop button, try to restart spindle rotation by turning variable speed dial all the way coun- terclockwise to "0" and then clockwise. The spindle should not start.

—If spindle does start with Emergency Stop button pressed in, the button is not oper- ating correctly. This safety feature must operate properly before continuing opera- tion. Turn variable speed dial counterclock- wise to "0" to stop lathe, disconnect it from power, and call Tech Support for help.

Congratulations! The test run is complete. Turn lathe OFF and perform the following Spindle Break-Inprocedure.

-22-

Model G0765 (Mfd. Since 12/13)

Image 24
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Service Control Panel WiringIntroduction Machine Description Manual AccuracyContact Info Identification Controls Components Control PanelCarriage Tailstock Rear Controls End GearsMachine Data Sheet Tailstock Info Features Safety Safety Instructions for MachineryPage Additional Safety for Metal Lathes Additional Chuck Safety Power Supply AvailabilityFull-Load Current Rating 110V Circuit RequirementsGrounding & Plug Requirements Extension CordsMinimum Gauge Size 14 AWG 50 ftSetup Needed for SetupPreparation UnpackingInstalled Components Figure Qty InventoryPackaged Components Figures Qty Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Assembly Power ConnectionConnecting Power Disconnecting PowerTest Run Disengaged Recommended Adjustments Factory adjustments that should be verifiedSpindle Break-In Operations Operation OverviewInstallation Removal Device Chuck & Faceplate MountingChuck Installation To install the chuckTools Needed Qty Scroll Chuck Clamping Changing Jaw SetTo change the jaw set Faceplate To mount a non-concentric workpiece to the faceplateUsing Quill TailstockTailstock Quill Specs Positioning TailstockInstalling Tooling Offsetting TailstockTo install tooling in the tailstock Removing ToolingAligning Tailstock to Spindle Centerline To offset the tailstockItems Needed Qty To align the tailstock to the spindle centerlinePage Centers Dead CentersMounting Dead Center in Spindle Removing Center from SpindleMounting Center in Tailstock Removing Center from TailstockMounting Workpiece Between Centers To mount a center in the tailstockTools Needed for Installation/Removal Qty To install and use the steady restSteady Rest Installing Tool Compound Rest Four-Way Tool PostAligning Cutting Tool with Spindle Centerline Below are two common methodsTo align cutting tool with tailstock center Top ViewManual Feed Spindle SpeedSetting Spindle Speed Range Setting Spindle Direction & SpeedConfiguration Example To set spindle speed to 100 RPMPower Feed Power Feed ControlsSetting Power Feed Rate To set power feed for 0.04 in./revPrimary Threading Configuration Power Feed ConfigurationSecondary Threading Configuration End GearsEnd Gear Configuration Example To configure end gears for threading 20 TPI40T 65T Gear 50 T Ge ar 20 TPI Page Threading Headstock Threading ControlsTo set the lathe to thread 20 TPI Feed Direction LeverThread Dial Chart Apron Threading ControlsThread Dial Dial Number Thread Dial Accessories D3640-Shop Fox Tool Table PlusMaintenance Cleaning/ProtectingSchedule Lubrication Lubrication FrequencyBall Oilers Leadscrew & Carriage Rack BedwaysCross Slide & Compound Slide Machine Storage Change Gear BushingTumbler Gears Preparing Lathe for StorageService TroubleshootingSymptom Possible Cause Possible Solution Lathe Operation Backlash Adjustment Leadscrew End-Play AdjustmentCross Slide To remove leadscrew end playGib Adjustment To adjust cross slide and compound slide gibsHalf Nut Adjustment Fuse ReplacementTo adjust half nut To replace fuseBrush Replacement To replace motor brushesTiming Belt Tension Replacement Tensioning Timing BeltReplacing Timing Belt Wiring Wiring Safety InstructionsControl Panel Wiring Machine FrameControl Panel Wiring Photos G0765 wiring overviewMotor/Speed Sensor/ Plug Wiring 110 VACMain Description Description Labels & Cosmetics Front 255 254 256 257 259 258 253 252 261 251 260Threading Charts AppendixWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns