Grizzly MODEL G0765 owner manual Installing Tooling, Removing Tooling, Offsetting Tailstock

Page 33

Installing Tooling

The tailstock quill accepts MT#2 tapered arbors (see the Figures below for examples).

 

 

 

 

 

 

 

 

 

 

 

 

Tang

 

 

 

 

 

 

 

 

 

 

Screw

 

 

 

 

 

 

 

 

 

Solid

 

 

 

 

Solid

 

Open

 

 

End

 

 

 

 

 

 

 

 

End

 

 

 

 

 

 

End

 

End

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 28. Types of tapered arbors and tooling.

Figure 29. Example photos of inserting tools into

the tailstock.

Model G0765 (Mfd. Since 12/13)

Note: If the tooling has an open hole in the end, then a screw can be threaded into the end of the tool to provide a solid surface for the quill pin to push against when the quill is retracted for tool removal. Otherwise, removal of such tooling may be difficult.

To install tooling in the tailstock:

1.With tailstock locked in place, unlock quill, then use handwheel to extend it approxi- mately 1".

2.Thoroughly clean and dry tapered mating surfaces of quill and center, making sure no lint or oil remains on tapers.

3.With a firm and quick motion, insert tool into quill. Check to see if it is firmly seated by attempting to twist it—a firmly seated tool will not twist.

4.Unlock tailstock and move it until tip of tool is close to, but not touching, workpiece, then lock tailstock.

5.Start spindle rotation, unlock quill lock lever, then turn quill handwheel clockwise to feed tool into workpiece.

Removing Tooling

1.Use shop rag to hold tool.

2.Rotate quill handwheel counterclockwise to fully retract quill into tailstock until tool is forced out of quill.

Offsetting Tailstock

The tailstock quill can be offset from the spin- dle centerline for turning tapers. Offsetting quill toward the front of the lathe results in a taper at the tailstock end. Conversely, offsetting quill toward the back of the lathe results in a taper at the spindle end.

-31-

Image 33
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Control Panel Wiring ServiceIntroduction Machine Description Manual AccuracyContact Info Identification Controls Components Control PanelCarriage End Gears Tailstock Rear ControlsMachine Data Sheet Tailstock Info Features Safety Instructions for Machinery SafetyPage Additional Safety for Metal Lathes Additional Chuck Safety Availability Power SupplyFull-Load Current Rating 110V Circuit RequirementsExtension Cords Grounding & Plug RequirementsMinimum Gauge Size 14 AWG 50 ftNeeded for Setup SetupPreparation UnpackingInstalled Components Figure Qty InventoryPackaged Components Figures Qty Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Power Connection AssemblyConnecting Power Disconnecting PowerTest Run Disengaged Recommended Adjustments Factory adjustments that should be verifiedSpindle Break-In Operation Overview OperationsChuck & Faceplate Mounting Installation Removal DeviceChuck Installation To install the chuckTools Needed Qty Changing Jaw Set Scroll Chuck ClampingTo change the jaw set To mount a non-concentric workpiece to the faceplate FaceplateTailstock Using QuillTailstock Quill Specs Positioning TailstockOffsetting Tailstock Installing ToolingTo install tooling in the tailstock Removing ToolingTo offset the tailstock Aligning Tailstock to Spindle CenterlineItems Needed Qty To align the tailstock to the spindle centerlinePage Dead Centers CentersMounting Dead Center in Spindle Removing Center from SpindleRemoving Center from Tailstock Mounting Center in TailstockMounting Workpiece Between Centers To mount a center in the tailstockTools Needed for Installation/Removal Qty To install and use the steady restSteady Rest Compound Rest Four-Way Tool Post Installing ToolBelow are two common methods Aligning Cutting Tool with Spindle CenterlineTo align cutting tool with tailstock center Top ViewSpindle Speed Manual FeedSetting Spindle Direction & Speed Setting Spindle Speed RangeConfiguration Example To set spindle speed to 100 RPMPower Feed Controls Power FeedTo set power feed for 0.04 in./rev Setting Power Feed RatePower Feed Configuration Primary Threading ConfigurationSecondary Threading Configuration End GearsEnd Gear Configuration Example To configure end gears for threading 20 TPI40T 65T Gear 50 T Ge ar 20 TPI Page Headstock Threading Controls ThreadingTo set the lathe to thread 20 TPI Feed Direction LeverThread Dial Chart Apron Threading ControlsThread Dial Dial Number Thread Dial D3640-Shop Fox Tool Table Plus AccessoriesMaintenance Cleaning/ProtectingSchedule Lubrication Lubrication FrequencyBall Oilers Leadscrew & Carriage Rack BedwaysCross Slide & Compound Slide Change Gear Bushing Machine StorageTumbler Gears Preparing Lathe for StorageService TroubleshootingSymptom Possible Cause Possible Solution Lathe Operation Leadscrew End-Play Adjustment Backlash AdjustmentCross Slide To remove leadscrew end playTo adjust cross slide and compound slide gibs Gib AdjustmentFuse Replacement Half Nut AdjustmentTo adjust half nut To replace fuseTo replace motor brushes Brush ReplacementTensioning Timing Belt Timing Belt Tension ReplacementReplacing Timing Belt Wiring Safety Instructions WiringMachine Frame Control Panel WiringG0765 wiring overview Control Panel Wiring Photos110 VAC Motor/Speed Sensor/ Plug WiringMain Description Description 255 254 256 257 259 258 253 252 261 251 260 Labels & Cosmetics FrontAppendix Threading ChartsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty & Returns