Grizzly MODEL G0765 owner manual

Page 2

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to proper installation in a safe environment, personnel training and usage authorization, proper inspection and maintenance, manual availability and compre- hension, application of safety devices, cutting/sanding/grinding tool integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead-based paints.

Crystalline silica from bricks, cement and other masonry products.

Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: Work in a well ventilated area, and work with approved safety equip- ment, such as those dust masks that are specially designed to filter out microscopic particles.

Image 2
Contents Model G0765 14 Benchtop Lathe Page Table of Contents Service Control Panel WiringContact Info IntroductionMachine Description Manual Accuracy Identification Carriage Controls ComponentsControl Panel Tailstock Rear Controls End GearsMachine Data Sheet Tailstock Info Features Safety Safety Instructions for MachineryPage Additional Safety for Metal Lathes Additional Chuck Safety Full-Load Current Rating Power SupplyAvailability 110V Circuit RequirementsMinimum Gauge Size 14 AWG Grounding & Plug RequirementsExtension Cords 50 ftPreparation SetupNeeded for Setup UnpackingPackaged Components Figures Qty Installed Components Figure QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Connecting Power AssemblyPower Connection Disconnecting PowerTest Run Disengaged Spindle Break-In Recommended AdjustmentsFactory adjustments that should be verified Operations Operation OverviewInstallation Removal Device Chuck & Faceplate MountingTools Needed Qty Chuck InstallationTo install the chuck Scroll Chuck Clamping Changing Jaw SetTo change the jaw set Faceplate To mount a non-concentric workpiece to the faceplateTailstock Quill Specs Using QuillTailstock Positioning TailstockTo install tooling in the tailstock Installing ToolingOffsetting Tailstock Removing ToolingItems Needed Qty Aligning Tailstock to Spindle CenterlineTo offset the tailstock To align the tailstock to the spindle centerlinePage Mounting Dead Center in Spindle CentersDead Centers Removing Center from SpindleMounting Workpiece Between Centers Mounting Center in TailstockRemoving Center from Tailstock To mount a center in the tailstockSteady Rest Tools Needed for Installation/Removal QtyTo install and use the steady rest Installing Tool Compound Rest Four-Way Tool PostTo align cutting tool with tailstock center Aligning Cutting Tool with Spindle CenterlineBelow are two common methods Top ViewManual Feed Spindle SpeedConfiguration Example Setting Spindle Speed RangeSetting Spindle Direction & Speed To set spindle speed to 100 RPMPower Feed Power Feed ControlsSetting Power Feed Rate To set power feed for 0.04 in./revSecondary Threading Configuration Primary Threading ConfigurationPower Feed Configuration End Gears40T 65T Gear 50 T Ge ar 20 TPI End Gear Configuration ExampleTo configure end gears for threading 20 TPI Page To set the lathe to thread 20 TPI ThreadingHeadstock Threading Controls Feed Direction LeverThread Dial Thread Dial ChartApron Threading Controls Dial Number Thread Dial Accessories D3640-Shop Fox Tool Table PlusSchedule MaintenanceCleaning/Protecting Ball Oilers LubricationLubrication Frequency Cross Slide & Compound Slide Leadscrew & Carriage RackBedways Tumbler Gears Machine StorageChange Gear Bushing Preparing Lathe for StorageSymptom Possible Cause Possible Solution ServiceTroubleshooting Lathe Operation Cross Slide Backlash AdjustmentLeadscrew End-Play Adjustment To remove leadscrew end playGib Adjustment To adjust cross slide and compound slide gibsTo adjust half nut Half Nut AdjustmentFuse Replacement To replace fuseBrush Replacement To replace motor brushesTiming Belt Tension Replacement Tensioning Timing BeltReplacing Timing Belt Wiring Wiring Safety InstructionsControl Panel Wiring Machine FrameControl Panel Wiring Photos G0765 wiring overviewMotor/Speed Sensor/ Plug Wiring 110 VACMain Description Description Labels & Cosmetics Front 255 254 256 257 259 258 253 252 261 251 260Threading Charts AppendixWarranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns