Delta 638518-00 Changing Blades, Dust Chute, Wrench Storage, Carefully Turn Blade Inside OUT

Page 16

CHANGING BLADES

DISCONNECT MACHINE FROM POWER SOURCE.

To change blades:

1.Press in door latches (A) Fig. 34, and open door (B) as shown.

2.Loosen two screws (C) Fig. 35, and remove blade guard (D).

3.Release tension on the band saw blade by turning tension knob (E) Fig. 34 counterclockwise.

4.Remove table alignment screw (F) Fig. 36.

5.Slip the blade off both wheels and guide it out through the slot in the table.

6.Check the new blade to make sure that the teeth will point down toward the table when installed. IF NOT,

CAREFULLY TURN BLADE INSIDE OUT.

7.Place the new blade onto wheels and adjust blade tension, blade guides and tracking as described previously in this manual.

8.Replace blade guard, which was removed in STEP 2, and table alignment screw which was removed in STEP 4.

9.Close door (B) Fig. 34, before operating saw.

E

A

B

A

Fig. 34

DUST CHUTE

A dust collection system can be attached to the 13/4 " O.D. dust chute (A) Fig. 37.

WRENCH STORAGE

The 3mm and 4mm wrenches (A) supplied with your band saw can be stored inside the wheel cover as shown in Fig. 37A.

C

D

Fig. 35

F

Fig. 36

A

A

Fig. 37

Fig. 37A

16

Image 16
Contents Bench Band Saw Safety Guidelines Definitions General Safety RulesStay ALERT, Watch What YOU are Doing Additional Safety Rules for Band Saws This Band SAW is Intended for Indoor USE onlyPower Connections Grounding InstructionsUnpacking and Cleaning Extension CordsBench Band SAW Parts Assembling Table To Machine AssemblyClosing Door Page Attaching Lamp to Machine Fastening Band SAW To Supporting SurfaceOperating Controls and Adjustments Locking Switch OFF PositionStarting Stopping SAW Opening and Closing DoorAdjusting Blade Tension Adjusting Upper Blade Guide AssemblyDisconnect Machine from Power Source Tracking the BladeAdjusting Upper Blade Guides and Blade Support Bearing Adjusting Lower Blade Guides and Blade Support Bearing Tilting the TableAdjusting the Table Positive Stops Adjusting Belt TensionChanging Blades Dust ChuteWrench Storage Carefully Turn Blade Inside OUTMiter Guage Optional Operating the Band SAWCutting Curves Page Troubleshooting Guide RemedyTroubleshooting Guide Band SAW Blades Page Page Accessories MaintenanceSierra de Cinta de 9 pulg. para Banquillo Pautas DE Seguridad / Definiciones Normas DE Seguridad GeneralesPage Guarde Estas Instrucciones Conexiones a LA Fuente DE Alimentación Instrucciones DE Conexión a TierraInstrucciones DE Funcionamiento Cordones DE ExtensiónDesempaquetado Y Limpieza Partes DE LA Sierra DE LA Venda DEL Banco 9 pulg Montaje Montaje DE LA Mesa a LA MaquinaPage Montaje DE LA Lampara a LA Maquina Afianzando LA Sierra DE Cinta a LA Superficie DE ApoyoControles DE Funcionamiento Y Ajustes Arrancando Y Deteniendo LA SierraBloqueando EL Interruptor EN LA Posicion DE Apagado Abriendo Y Cerrando LA Puerta BisagradaCompensacion DE LA Hoja Ajustando LA Tension DE LA HojaAjustando EL Ensamblado DE LA Guia DE Hoja Superior Desconecte LA Maquina DE LA Fuente DE Energia Inclinando LA Mesa Ajustando LOS Topes Positivos DE LA Mesa Ajustando LA Tension DE LA CorreaCambio DE Hojas Almacenamiento Para LlavesOperacion DE LA Sierra DE Cinta Corte DE CurvasPage Guia DE Localizacion DE Averias Causa probableContinuacion Hojas DE Sierra DE Cinta Notas Accesorios MantenimientoPIEZAS, Servicio O Asistencia DE Garantía Modèle SM400 Règles Générales DE Sécurité Lignes Directrices EN Matière DE Sécurité DéfinitionsAU Canada 505, PROM. SOUTHGATE, GUELPH, Ontario N1H 6M7 Mettre Latelier À Lépreuve DES Enfants Règles DE Sécurité Supplémentaires Pour LES Scies À Ruban Utiliser LA Scie À Lame Ruban Uniquement À L’INTÉRIEURConnexions Électriques Directives D’UTILISATION Rallonges ÉlectriquesDésemballage ET Nettoyage Pièces DE LA Scie À Lame Ruban DE Po 22,86 cmAssemblage DE LA Table À LA Machine AssemblageOuvrir ET Fermer LA Porte » Page Fixer LA Lampe À Lappareil Fixer LA Scie À Lame Ruban À LA Surface DE SupportDémarrage ET Arrêt DE LA Scie Utilisation DES Commandes ET RéglagesOuvrir ET Fermer LA Porte Réglage LA Tension DE LA Lame Alignement DE LA LameRéglage DU Module DU Guide DE Lame Supérieure LA Tension DE LA Lame »Page Inclinaison DE LA Table Réglage DES Butées Fixes DE LA Table Réglage LA Tension DE LA CourroieGoulotte DE Poussière Changement DES LamesRangement DE LA CLÉ Jauge À Onglet Facultatif Utilisation DE LA Scie À Lame RubanCoupe DE Courbes Page Cause probable Solution Guide DE DépannageProblème LA Lame NE Saligne PAS Lames DE Scie À Lame Ruban Remarques Remarques Accessoires FonctionnementRéparation GarantiePORTER-CABLE · Delta Service Centers