Delta 638518-00, SM400 instruction manual Troubleshooting Guide

Page 20

 

TROUBLESHOOTING GUIDE

 

 

(CONTINUED)

 

 

 

Trouble: BLADE WILL NOT TRACK.

 

 

Probable Cause

Remedy

1.

Blade too loose

1.

Adjust tension

2.

Upper wheel not properly adjusted.

2.

Adjust upper wheel.

3.

Improperly adjusted blade support bearing.

3.

Adjust blade support bearing.

Trouble: CUT DOES NOT AGREE WITH SETTING ON THE TILT SCALE.

Probable Cause

Remedy

1.

Pointer out of adjustment

1.

Adjust pointer.

Trouble: BLADE WILL NOT STAY ON WHEEL.

Probable Cause

1.Blade not tensioned properly.

2.Blade guides improperly adjusted.

3.Blade support bearing improperly adjusted.

4.Blade wheel not tracking properly.

5.Bad weld on blade.

6.Worn tires.

Trouble: BAND SAW MAKES UNSATISFACTORY CUTS.

Probable Cause

1.Blade not tensioned properly.

2.Blade guides improperly adjusted.

3.Blade support bearing improperly set.

4.Blade wheel not tracking properly.

5.Bad weld on blade.

6.Worn tires.

7.Incorrect blade for work being done.

8.Dull blade or insufficient set.

9.Upper blade guide set too high.

10.Continuous running of machine when not actually cutting.

Remedy

1.Adjust blade tension.

2.Check and adjust blade guides.

3.Adjust blade support bearing.

4.Check and adjust blade tracking.

5.Replace the blade.

6.Replace tires.

Remedy

1.Adjust blade tension.

2.Check and adjust blade guides.

3.Adjust blade support bearing.

4.Check and adjust blade tracking.

5.Replace the blade.

6.Replace tires.

7.Change the blade.

8.Replace blade.

9.Set upper blade guide within 1/8" of work piece.

10.Turn off machine when not performing cutting operation.

20

Image 20
Contents Bench Band Saw Safety Guidelines Definitions General Safety RulesStay ALERT, Watch What YOU are Doing Additional Safety Rules for Band Saws This Band SAW is Intended for Indoor USE onlyPower Connections Grounding InstructionsUnpacking and Cleaning Extension CordsBench Band SAW Parts Closing Door AssemblyAssembling Table To Machine Page Attaching Lamp to Machine Fastening Band SAW To Supporting SurfaceOperating Controls and Adjustments Locking Switch OFF PositionStarting Stopping SAW Opening and Closing DoorAdjusting Blade Tension Adjusting Upper Blade Guide AssemblyDisconnect Machine from Power Source Tracking the BladeAdjusting Upper Blade Guides and Blade Support Bearing Adjusting Lower Blade Guides and Blade Support Bearing Tilting the TableAdjusting the Table Positive Stops Adjusting Belt TensionChanging Blades Dust ChuteWrench Storage Carefully Turn Blade Inside OUTCutting Curves Operating the Band SAWMiter Guage Optional Page Troubleshooting Guide RemedyTroubleshooting Guide Band SAW Blades Page Page Accessories MaintenanceSierra de Cinta de 9 pulg. para Banquillo Pautas DE Seguridad / Definiciones Normas DE Seguridad GeneralesPage Guarde Estas Instrucciones Conexiones a LA Fuente DE Alimentación Instrucciones DE Conexión a TierraDesempaquetado Y Limpieza Cordones DE ExtensiónInstrucciones DE Funcionamiento Partes DE LA Sierra DE LA Venda DEL Banco 9 pulg Montaje Montaje DE LA Mesa a LA MaquinaPage Montaje DE LA Lampara a LA Maquina Afianzando LA Sierra DE Cinta a LA Superficie DE ApoyoControles DE Funcionamiento Y Ajustes Arrancando Y Deteniendo LA SierraBloqueando EL Interruptor EN LA Posicion DE Apagado Abriendo Y Cerrando LA Puerta BisagradaAjustando EL Ensamblado DE LA Guia DE Hoja Superior Ajustando LA Tension DE LA HojaCompensacion DE LA Hoja Desconecte LA Maquina DE LA Fuente DE Energia Inclinando LA Mesa Ajustando LOS Topes Positivos DE LA Mesa Ajustando LA Tension DE LA CorreaCambio DE Hojas Almacenamiento Para LlavesOperacion DE LA Sierra DE Cinta Corte DE CurvasPage Guia DE Localizacion DE Averias Causa probableContinuacion Hojas DE Sierra DE Cinta Notas PIEZAS, Servicio O Asistencia DE Garantía MantenimientoAccesorios Modèle SM400 AU Canada 505, PROM. SOUTHGATE, GUELPH, Ontario N1H 6M7 Lignes Directrices EN Matière DE Sécurité DéfinitionsRègles Générales DE Sécurité Mettre Latelier À Lépreuve DES Enfants Règles DE Sécurité Supplémentaires Pour LES Scies À Ruban Utiliser LA Scie À Lame Ruban Uniquement À L’INTÉRIEURConnexions Électriques Désemballage ET Nettoyage Rallonges ÉlectriquesDirectives D’UTILISATION Pièces DE LA Scie À Lame Ruban DE Po 22,86 cmOuvrir ET Fermer LA Porte » AssemblageAssemblage DE LA Table À LA Machine Page Fixer LA Lampe À Lappareil Fixer LA Scie À Lame Ruban À LA Surface DE SupportOuvrir ET Fermer LA Porte Utilisation DES Commandes ET RéglagesDémarrage ET Arrêt DE LA Scie Réglage LA Tension DE LA Lame Alignement DE LA LameRéglage DU Module DU Guide DE Lame Supérieure LA Tension DE LA Lame »Page Inclinaison DE LA Table Réglage DES Butées Fixes DE LA Table Réglage LA Tension DE LA CourroieRangement DE LA CLÉ Changement DES LamesGoulotte DE Poussière Coupe DE Courbes Utilisation DE LA Scie À Lame RubanJauge À Onglet Facultatif Page Cause probable Solution Guide DE DépannageProblème LA Lame NE Saligne PAS Lames DE Scie À Lame Ruban Remarques Remarques Accessoires FonctionnementRéparation GarantiePORTER-CABLE · Delta Service Centers