Delta 90513776 Rotating the Table for Miter Cutting, Pointer and Scale, Adjusting the Pointer

Page 12

ROTATING THE TABLE FOR MITER CUTTING

Your miter saw will cut any angle from a straight 90° cut to 47° right and left. Turn the lock handle (A) Fig. 13 counter-clockwise one or two turns, depress the index lever (B), and move the control arm to the desired angle. Tighten the lock handle (A).

The miter saw is equipped with positive stops at the 0°, 22.5°, 31.62°, and 45° right and left positions. Loosen the lock handle (A) Fig. 14 and move the control arm until the bottom of the index lever (B) engages into one of the positive stops, four of which are shown at (C). Tighten the lock handle (A). To disengage the positive stop, depress the index lever (B).

A triangle indicator (D) Fig. 15 is provided on the miter scale at the 31.62° right and left miter positions for cutting crown moulding. (Refer to the “CUTTING CROWN MOULDING” section of this manual).

IMPORTANT: Always tighten the lock handle (A) Fig. 14 before cutting.

Fig. 13

B

C

A

Fig. 14

A

ADJUSTING THE SLIDING FIT BETWEEN THE MOVABLE TABLE AND THE BASE

DISCONNECT THE MACHINE FROM THE POWER SOURCE .

To adjust the sliding fit between the movable table and the base, turn the nut (A) Fig. 14A clockwise to increase the sliding fit (opposite to decrease the fit). This adjustment should not be so tight that it restricts the rotating movement of the table, or so loose that it affects the accuracy of the saw.

POINTER AND SCALE

The pointer (E) Fig. 15 indicates the angle of cut. Each line on the scale (F) represents 1 degree. When you move the pointer from one line to the next on the scale, you change the angle of cut by 1 degree.

A

Fig. 14A

ADJUSTING THE POINTER

To adjust the pointer (E) Fig. 16, loosen the screw (G), adjust the pointer (E), and tighten the screw.

F

Fig. 15

D

E

E

G

Fig. 16

LOCKING THE CUTTINGHEAD IN THE DOWN POSITION

To transport the saw, always lock the cuttinghead in the down position. Lower the cuttinghead (A) Fig.17, and push the cuttinghead lock knob (B) into the hole in the cutting arm until it locks the cuttinghead.

IMPORTANT: Carrying the machine by the switch handle will cause misalignment. Always lift the machine by the base or by the carrying handle (See Fig. 20).

A

B

Fig. 17

12

Image 12
Contents Compound Power Miter Saw Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules Important Safety InstructionsAdditional Specific Safety Rules USE only Blades of the Correct SizePower Connections Grounding InstructionsFunctional Description Extension CordsForeword Minimum Gauge Extension CordCarton Contents AssemblyDisconnect Machine from Power Source Attaching the Table Lock HandleRotating the Table to the 90 Degree Position Moving Cuttinghead to the UP Position Attaching the Dust BAGFastening the Machine to a Supporting Surface Using the Optional Work Clamp Locking the Switch in the OFF PositionOperation Table Hazard AreaAdjusting the Pointer Disconnect the Machine from the Power SourceRotating the Table for Miter Cutting Pointer and ScaleAdjusting Sliding Fence Adjusting the Blade Parallel to the Table SlotTilting the Cuttinghead for Bevel Cutting Rear SUPPORT/CARRYING HandleFence Adjustment Adjusting the Downward Travel of the SAW BladeAdjusting 90 and 45 Bevel Stops Adjusting the Tension of the Cuttinghead Return Spring Adjusting Sliding FIT Between Cuttinghead ARM and TrunnionAdjusting the Lower Blade Guard Disconnect the Machine from Power SourceTypical Operations and Helpful Hints Auxiliary Wood FenceGeneral Cutting Operations Cutting Aluminum RightWrong Cutting Crown Moulding Crown Moulding Other AnglesMaintenance Brush Inspection and ReplacementChanging the Blade Troubleshooting Keep the Machine CleanFailure to Start Service AccessoriesWarranty Sierra de Ingletes Compuesta Motorizada de 254 mm Instrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONES LA Propuesta 65 DE CaliforniaNo Exponga a LA Lluvia NI LA Utilice EN Lugares Húmedos Normas Generales DE Seguridad Instrucciones Importantes Sobre SeguridadNormas Específicas Adicionales DE Seguridad Nunca Corte DE Nuevo Pedazos PequeñosConexiones a LA Fuente DE Alimentación Instrucciones DE Conexión a TierraCordones DE Extensión Instrucciones DE FuncionamientoContenido DE LA Caja PrefacioEnsamblaje OperaciónUtilizar LA Abrazadera Opcional DEL Trabajo Arrancando Y Deteniendo LA MaquinaFijando EL Interruptor EN LA Posicion DE Apagado Rotacion DE LA Mesa Para EL Corte DE IngletesAdjustando LA Hoja Paralelamente a LA Ranura DE LA Mesa Ajuste DE LA Guía DeslizanteApoyo Posterior / Agarradera Para Portar Regulación DEL RebordeAjuste DEL Protector Inferior DE LA Hoja Funciones Tipicas Y Consejos UtilesRefrentado DE Madera Auxiliar Operaciones Generales DEL CorteCorte DEL Aluminio Corte DE Materiales ArqueadosMantenimiento Cambio DE LA HojaInspeccion Y Reemplazo DE LOS Cepillos Mantenga LAS Herramientas LimpiasLocalizacion DE Fallas Quel EST LE Problème ? QUE FAIRE…Servicio AccesoriosGarantia Modèle SM100M Directives DE Sécurité Importantes Conserver CES DirectivesPage Règles Générales DE Sécurité Directives DE Sécurité ImportantesRègles DE Sécurité Spécifiques Supplémentaires Conserver CES DirectivesConnexions Électriques Directives DE Mise À LA TerreDescription Fonctionnelle Contenu DU CartonRallonges Électriques AVANT-PROPOSAssemblage FonctionnementDémarrage ET Arrêt DE LA Scie À Onglets Verrouillage DE L’INTERRUPTEUR EN Position D’ARRÊTTourner LA Table Pour Effectuer UNE Coupe À Onglet Pointeur ET ÉchelleRéglage DU Guide Coulissant Support ARRIÈRE/POIGNÉE DE TransportAjuster LA Lame Parallèlement À LA Fente DE LA Table Réglage DU Guide À 90 DE LA LameRéglage DU PROTÈGE-LAME Inférieur Opérations Courantes ET Conseils UtilesGuide Auxiliaire EN Bois Opérations DE Coupe GénéralesEntretien Coupe DE Moulures CouronnéesMoulure Couronnée Autres AnglesInspection ET Remplacement DE LA Brosse DépannageGarder LA Machine Propre Démarrage ImpossibleAccessoires RéparationGarantie PORTER-CABLE · Delta Service Centers