Delta 90513776 instruction manual Cutting Crown Moulding, Crown Moulding Other Angles

Page 19

CUTTING CROWN MOULDING

One of the many features of the saw is the ease of cutting crown moulding. The following is an example of cutting both inside and outside corners on 52°/38° wall angle crown moulding.

1.Move the table to the 31.62° right miter position and lock the table in position. NOTE: A positive stop is provided to find this angle quickly.

2.Tilt the saw blade to the 33.86° left bevel position and tighten bevel lock handle. NOTE: A triangle indicator is provided on the bevel scale to find this angle quickly.

3.Place the crown moulding on the table with the CEILING EDGE of the moulding against the fence, and make the cut, as shown in Fig. 37.

NOTE: The piece of crown moulding used for the outside corner will always be on the right hand side of the blade, as shown at (A) Fig. 37. The piece of crown moulding used for the inside corner will always be on the left hand side of the blade, as shown at (B) Fig. 37.

4. To make the matching halves of the inside and outside corners, rotate the table to the 31.62° left miter position.

NOTE: A positive stop is provided to find this angle quickly. The saw blade is already tilted to the 33.86° left bevel position from the previous cut.

5.Place the crown moulding on the table with the WALL EDGE of the crown moulding against the fence and make the cut. Again, the piece of crown moulding used for the outside corner will always be on the right side of the blade, as shown at (C) Fig. 38. The piece of crown moulding used for the inside corner will always be on the left side of the blade, as shown at (D) Fig. 38.

6.Fig. 39 illustrates the two outside corner pieces; (A) being the piece cut at (A) Fig. 37 and (C) being the piece cut at (C) Fig. 38.

7.Fig. 40 illustrates the two inside corner pieces; (B) being the piece cut at (B) Fig. 37, and (D) being the piece cut at (D) Fig. 38.

45-45 CROWN MOULDING

NOTE: If you are cutting crown moulding that is 45°-45°, follow the same procedure above, with the exception that the bevel position will always be at 30° and the miter position will be 35-1/4° to the right or left.

OTHER ANGLES

NOTE: The above instructions are assuming the angle between the walls is 90°. If you need help cutting crown moulding set at angles other than 90°, see the instruction sheet “CUTTING CROWN MOULDING” on the Delta Machinery web site at www.deltamachinery.com.

B

A

WALL

EDGE

CEILING

EDGE

D

C

Fig. 37

Fig. 38

C

A

B

D

Fig. 39

Fig. 40

19

Image 19
Contents Compound Power Miter Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesUSE only Blades of the Correct Size Additional Specific Safety RulesGrounding Instructions Power ConnectionsMinimum Gauge Extension Cord Functional DescriptionExtension Cords ForewordAssembly Carton ContentsAttaching the Table Lock Handle Disconnect Machine from Power SourceRotating the Table to the 90 Degree Position Attaching the Dust BAG Moving Cuttinghead to the UP PositionFastening the Machine to a Supporting Surface Table Hazard Area Using the Optional Work ClampLocking the Switch in the OFF Position OperationPointer and Scale Adjusting the PointerDisconnect the Machine from the Power Source Rotating the Table for Miter CuttingRear SUPPORT/CARRYING Handle Adjusting Sliding FenceAdjusting the Blade Parallel to the Table Slot Tilting the Cuttinghead for Bevel CuttingAdjusting the Downward Travel of the SAW Blade Fence AdjustmentAdjusting 90 and 45 Bevel Stops Adjusting Sliding FIT Between Cuttinghead ARM and Trunnion Adjusting the Tension of the Cuttinghead Return SpringAuxiliary Wood Fence Adjusting the Lower Blade GuardDisconnect the Machine from Power Source Typical Operations and Helpful HintsGeneral Cutting Operations Right Cutting AluminumWrong Crown Moulding Other Angles Cutting Crown MouldingBrush Inspection and Replacement MaintenanceChanging the Blade Keep the Machine Clean TroubleshootingFailure to Start Accessories ServiceWarranty Sierra de Ingletes Compuesta Motorizada de 254 mm Instrucciones DE Seguridad Importantes LA Propuesta 65 DE California Pautas DE SEGURIDAD/DEFINICIONESNo Exponga a LA Lluvia NI LA Utilice EN Lugares Húmedos Instrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadNunca Corte DE Nuevo Pedazos Pequeños Normas Específicas Adicionales DE SeguridadInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónPrefacio Cordones DE ExtensiónInstrucciones DE Funcionamiento Contenido DE LA CajaOperación EnsamblajeRotacion DE LA Mesa Para EL Corte DE Ingletes Utilizar LA Abrazadera Opcional DEL TrabajoArrancando Y Deteniendo LA Maquina Fijando EL Interruptor EN LA Posicion DE ApagadoRegulación DEL Reborde Adjustando LA Hoja Paralelamente a LA Ranura DE LA MesaAjuste DE LA Guía Deslizante Apoyo Posterior / Agarradera Para PortarOperaciones Generales DEL Corte Ajuste DEL Protector Inferior DE LA HojaFunciones Tipicas Y Consejos Utiles Refrentado DE Madera AuxiliarCorte DE Materiales Arqueados Corte DEL AluminioMantenga LAS Herramientas Limpias MantenimientoCambio DE LA Hoja Inspeccion Y Reemplazo DE LOS CepillosQuel EST LE Problème ? QUE FAIRE… Localizacion DE FallasAccesorios ServicioGarantia Modèle SM100M Conserver CES Directives Directives DE Sécurité ImportantesPage Directives DE Sécurité Importantes Règles Générales DE SécuritéConserver CES Directives Règles DE Sécurité Spécifiques SupplémentairesDirectives DE Mise À LA Terre Connexions ÉlectriquesAVANT-PROPOS Description FonctionnelleContenu DU Carton Rallonges ÉlectriquesFonctionnement AssemblagePointeur ET Échelle Démarrage ET Arrêt DE LA Scie À OngletsVerrouillage DE L’INTERRUPTEUR EN Position D’ARRÊT Tourner LA Table Pour Effectuer UNE Coupe À OngletRéglage DU Guide À 90 DE LA Lame Réglage DU Guide CoulissantSupport ARRIÈRE/POIGNÉE DE Transport Ajuster LA Lame Parallèlement À LA Fente DE LA TableOpérations DE Coupe Générales Réglage DU PROTÈGE-LAME InférieurOpérations Courantes ET Conseils Utiles Guide Auxiliaire EN BoisAutres Angles EntretienCoupe DE Moulures Couronnées Moulure CouronnéeDémarrage Impossible Inspection ET Remplacement DE LA BrosseDépannage Garder LA Machine PropreRéparation AccessoiresGarantie PORTER-CABLE · Delta Service Centers