Delta 90513776 instruction manual Operation, Table Hazard Area, Using the Optional Work Clamp

Page 11

OPERATION

OPERATIONAL CONTROLS AND ADJUSTMENTS

TABLE HAZARD AREA

The area inside the two red lines on the table (A) Fig. 9 is designated as a "HAZARD ZONE". Never place your hands inside this area while the machine is running. Maintain hands 6” from blade.

A

B

Fig. 9

USING THE OPTIONAL WORK CLAMP

1.An optional work clamp (A) Fig. 10 is available. Use this accessory clamp, especially with short workpieces. Never allow your hands to be in the “Hazard Zone”.

2.Two holes (B) Fig. 9 are provided in the base of the miter saw, enabling you to use the clamp (A) Fig.10 on either the right or left hand side of the saw blade.

Keep your hands out of path of saw blade. If necessary, clamp the workpiece in place before making the cut if hands would be within 6” of the blade.

A

Fig. 10

STARTING AND STOPPING THE MITER SAW

To start the miter saw, depress the switch trigger (A) Fig. 11 To stop the miter saw, release the switch trigger.

This saw is equipped with an automatic electric blade brake. As soon as the switch trigger (A) Fig. 11, is released, the electric brake is activated and stops the blade in seconds.

A turning saw blade can be dangerous. After completing cut, release switch trigger (A) Fig. 11, to activate blade brake. Keep cuttinghead down until blade has come to a complete stop.

The torque developed during braking may loosen the arbor screw (E) Fig. 45. The arbor screw should be checked periodically and tightened if necessary.

LOCKING THE SWITCH IN THE “OFF” POSITION

IMPORTANT: When the miter saw is not in use, the switch should be locked in the "OFF" position using a padlock (B) Fig. 12, with a 3/16" diameter shackle to prevent unauthorized use of the saw.

A

B

Fig. 11

Fig. 12

11

Image 11
Contents Compound Power Miter Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesUSE only Blades of the Correct Size Additional Specific Safety RulesGrounding Instructions Power ConnectionsMinimum Gauge Extension Cord Functional DescriptionExtension Cords ForewordAssembly Carton ContentsRotating the Table to the 90 Degree Position Disconnect Machine from Power SourceAttaching the Table Lock Handle Fastening the Machine to a Supporting Surface Moving Cuttinghead to the UP PositionAttaching the Dust BAG Table Hazard Area Using the Optional Work ClampLocking the Switch in the OFF Position OperationPointer and Scale Adjusting the PointerDisconnect the Machine from the Power Source Rotating the Table for Miter CuttingRear SUPPORT/CARRYING Handle Adjusting Sliding FenceAdjusting the Blade Parallel to the Table Slot Tilting the Cuttinghead for Bevel CuttingAdjusting 90 and 45 Bevel Stops Fence AdjustmentAdjusting the Downward Travel of the SAW Blade Adjusting Sliding FIT Between Cuttinghead ARM and Trunnion Adjusting the Tension of the Cuttinghead Return SpringAuxiliary Wood Fence Adjusting the Lower Blade GuardDisconnect the Machine from Power Source Typical Operations and Helpful HintsGeneral Cutting Operations Wrong Cutting AluminumRight Crown Moulding Other Angles Cutting Crown MouldingChanging the Blade MaintenanceBrush Inspection and Replacement Failure to Start TroubleshootingKeep the Machine Clean Warranty ServiceAccessories Sierra de Ingletes Compuesta Motorizada de 254 mm Instrucciones DE Seguridad Importantes No Exponga a LA Lluvia NI LA Utilice EN Lugares Húmedos Pautas DE SEGURIDAD/DEFINICIONESLA Propuesta 65 DE California Instrucciones Importantes Sobre Seguridad Normas Generales DE SeguridadNunca Corte DE Nuevo Pedazos Pequeños Normas Específicas Adicionales DE SeguridadInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónPrefacio Cordones DE ExtensiónInstrucciones DE Funcionamiento Contenido DE LA CajaOperación EnsamblajeRotacion DE LA Mesa Para EL Corte DE Ingletes Utilizar LA Abrazadera Opcional DEL TrabajoArrancando Y Deteniendo LA Maquina Fijando EL Interruptor EN LA Posicion DE ApagadoRegulación DEL Reborde Adjustando LA Hoja Paralelamente a LA Ranura DE LA MesaAjuste DE LA Guía Deslizante Apoyo Posterior / Agarradera Para PortarOperaciones Generales DEL Corte Ajuste DEL Protector Inferior DE LA HojaFunciones Tipicas Y Consejos Utiles Refrentado DE Madera AuxiliarCorte DE Materiales Arqueados Corte DEL AluminioMantenga LAS Herramientas Limpias MantenimientoCambio DE LA Hoja Inspeccion Y Reemplazo DE LOS CepillosQuel EST LE Problème ? QUE FAIRE… Localizacion DE FallasGarantia ServicioAccesorios Modèle SM100M Conserver CES Directives Directives DE Sécurité ImportantesPage Directives DE Sécurité Importantes Règles Générales DE SécuritéConserver CES Directives Règles DE Sécurité Spécifiques SupplémentairesDirectives DE Mise À LA Terre Connexions ÉlectriquesAVANT-PROPOS Description FonctionnelleContenu DU Carton Rallonges ÉlectriquesFonctionnement AssemblagePointeur ET Échelle Démarrage ET Arrêt DE LA Scie À OngletsVerrouillage DE L’INTERRUPTEUR EN Position D’ARRÊT Tourner LA Table Pour Effectuer UNE Coupe À OngletRéglage DU Guide À 90 DE LA Lame Réglage DU Guide CoulissantSupport ARRIÈRE/POIGNÉE DE Transport Ajuster LA Lame Parallèlement À LA Fente DE LA TableOpérations DE Coupe Générales Réglage DU PROTÈGE-LAME InférieurOpérations Courantes ET Conseils Utiles Guide Auxiliaire EN BoisAutres Angles EntretienCoupe DE Moulures Couronnées Moulure CouronnéeDémarrage Impossible Inspection ET Remplacement DE LA BrosseDépannage Garder LA Machine PropreGarantie AccessoiresRéparation PORTER-CABLE · Delta Service Centers