Craftsman 113.248510 owner manual Model, Assembling Cabinet

Page 13

. Use truss head bolts, Iockwashers, and hex nuts to mount the two (2) rear legs to the basic saw assem- bly. It may be necessary to slightly tilt the saw as- sembly backwards in order to get the four (4)holes in each corner of the saw to line up with the four (4) holes in the top of each leg. Finger tighten nuts at this time.

. Attach the four (4) lower stiffeners to the legs. Two (2) truss head bolts, washers, and hex nuts are re- quired to hold each end of alowerstiffener in place. Only hand tighten hex nuts.

7.Go back with a 7/_6wrench or socket and tighten all hex nuts.

8.Carefully lift the saw into its normal position. It may be necessary to have someone help you in order to avoid damaging the saw.

ADJUSTING LEVELING FEET

WARNING: TO AVOID INJURY FROM UNEX-

PECTED SAW OR WORK MOVEMENT, LEVEL- ING FEET MUST BE ADJUSTED SO THAT SAW

DOES NOT ROCK.

To adjust leveling feet so the saw will sit properly: a. Move saw to desired location.

b. Raise or lower leveling foot by turning it clockwise or counterclockwise.

c. Tighten nuts to lock leveling foot in place.

TRUSS HEAD BOLT "-'-'_' .-J.__

 

,._j_

 

WASHER

LEG .

_ _S_/_

:1i

HEXNu,

///_

,,/LL_--_ --

 

i

 

 

S FFE.ER

MODEL 113.248510

ASSEMBLING CABINET

1.Separate all "loose" parts from packing materials and check each item with "Parts List" to make sure all items are accounted for before discard-

ing any packing material.

From loose parts find the following items:

ITEM

DESCRIPTION

QTY.

1

Right Side Panel

1

2

Left Side Panel

1

3

Lower Shelf

1

4

Skirt

2

5

Shelf Stiffener

1

6

Corner Bracket

2

7

Spacer

2

8

Door

1

 

 

 

Bag of Loose Parts #507530

 

Bag of Loose Parts #508166

 

(In Cabinet Assembly)

 

Containing Following Items:

 

Containing Following Items:

 

Screw, Truss

Hd. 1/4-20 x 1/2

34

Screw,

Pan Hd. #6-10x 1/2

2

Lockwasher,

Ext. 1/4

34

Screw, Pan Hd. Ty "T" 6-32 x 318

2

Nut, Hex 1/4-20

34

Screw,

Pan Hd. #10-10x 1/2

4

Foot, Leveling 3/8

4

Catch

Magnetic

1

Nut, Hex Jam 3/8-16

8

Hinge

Door

2

13

Image 13
Contents 113.248320 Save This Manual For Future Reference113.248440113.248510 Table of Contents Keep Work Area Clean Know Your Power Tool Ground ALL ToolsUSE Recommended Accessories Never Stand on Tool Keep Guards in PlaceBefore Using the SAW Additional safety instructions for band sawWhen Installing or Moving the SAW Before Each USEBefore Sanding AccessoriesWhenever SAW is Running Glossary of terms for woodworking Power SupplyWire Sizes Motor Safety ProtectionSawdust from interfering with normal motor ventila- tion 25 Ft 26 50 Ft 100 FtGeneral information Unpacking and checking contentsDescription QTY Loose PartsTruss Head Screw 1/4-20x12 List of Loose Parts in BAG #507968List of Loose Parts in BAG #508014 Pan Hd. Screw 10-32 xNuts Support Bracke Leveling Foot Assembly and alignmentAttaching LEG SET Model 113.24821 ODescription Qty Truss Head Assembling Cabinet Model\ ,/o From loose parts bag find the following hard Mounting the SAW to the CabinetWare Front Attaching the Handwheel Model 113.248210 onlyMounting the Motor Find the following partsModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Steps are Completed Connecting the MotorChanging Speed Settings Recommended Speed SettingsModel 113.248320, 113.248440 Selecting Blade SpeedAttaching Trim Caps MODELS113.248210an¢ Getting to know your band sawOpen Battery Open Location and function of the electronic indicator systemBattery Cover Model 113.248440 & 113.248510 on LYFunction Keys Using the Electronic Indicator SystemRead-out Indicates correct tension for 3000Jrt,t Installing the BladeUpperblade tl t GU,DEsuPPO.TIIl-r LAligning the Blade and Blade Guide Assemblies Model 113.248440Blade Guide Turn front table over. Locate the two 2 latch Mounting FrontSprings, two 2 alignment springs, and the four 4-20 8 hex washer Head thread forming ScrewsHead Capscrew Squaring the Blade to the Table Adjusting Front Table Location and function of controls ON-OFF SwitchModel 113.248210 & 113,248320 Adjusting Bevel Lock Knob Sawdust Collection Basic band saw operationCircle Cutting Operation Recommended Blade SizeInstalling the Sanding Belt Installing Sanding AttachmentAdjusting Band SAW Bevel Travel MaintenanceAdjusting the Upper Blade Guide Travel Light Bulb Outlet Before Trouble Shooting Your Band SAW/SANDERTrouble Trouble shooting--motorProbable Cause RemedyProblem Trouble shooting -- electronicsProbable Cause Suggested Corrective Action 113.2485t Trouble shooting ---electronicsSuggested Corrective Action Parts List for Craftsman 12-INCH Band SAW Repair partsKey Part Description LegPage Key Drive Assembly PartsModel NOS .248210,113.248320, 113.248440 OMode1113.248320 Only ==Model113.248510 Only Base AssemblyModel NOS .248210,113.248320,113.248440 9414202 Bevel Drive and Motor Mount Assembly PartsScrew, Truss Hd /4-20 x 1/2 Parts List for Craftsman 12-INCH Electronic Band SAWPage Part Numberpartdescription Model Name of Item Airs