general information
ALL MODELS
1.This manual is for the following
113.248210,113.248320,113.248440, and113.248510. All sections are labeled with the correct model num- ber. Follow ONLY instructions that are meant for
your model saw.
2.Ifyou aremissing anypart(s)whileputtingyour saw together, do not continue assembly. Contact your Sears Service Center or Retail Store and get the
missing part(s) before continuing assembly or try- ing to use the saw.
Complete parts lists are located at the end of this manual. Use these liststo identifythe number of any
missing part.
3.Sometimes small parts get lost in packaging materi- als. Do not throw away any packaging until your saw is put together. If you are missing a part, check the packaging before contacting Sears.
Model Description
Model 113.248210: Manual Band Saw; 18x 23 inch work table; sLngle speed; 1/2H.P. motor that develops 1 H.P.; legset.
Model 113.248320: Manual Band Saw; 27 x 23 inch work table; two speed; 5/a H.P. motor that develops 11/8H.R; legset.
Model 113.248440: Electronic Band Saw; 27 x 23 inch work table; two speed; % H.P. motor that develops 11/8H.P.; legset.
Model 113.248510: Electronic Band Saw; 27 x 23 inch work table; two speed; 5/8 HP. motor that develops 11/8H.P.;23 inch cabinet with door.
unpacking and checking contents
ALL MODELS
TOOLS NEEDED
COMBINATION SQUARE MUST BE TRUE
STRAIGHT EDGE GF
BOARD
THIS EDGE MUST BE
f__./
MEDIUM SCREWDRIVER
PER_CTLY STRAIGHT
€
| @ |
|
|
| ||||||
.......... |
|
|
| 318" WRENCH | DRAW | LIGHT |
| |||
:_ |
|
|
|
| 7/16" | WRENCH | LINE | ON | BOARD | |
|
|
|
| ALONG |
| THIS | EDGIE | |||
|
|
|
|
| 9/16" | WRENCH |
| |||
SQUARE | _/ |
|
|
|
|
|
| t,_ | ||
|
|
|
| 7116" | SOCKET |
|
|
|
| / |
|
|
|
| 9/16" | SOCKET |
|
|
|
| |
1/8" | HEX | "L" | WRENCH |
|
|
|
|
|
| |
5/32" | HEX | "L" | WRENCH | _ | SOCKET WRENCH |
|
|
| ||
|
|
|
|
|
|
| SHOULD BE NO GAP OR OVERLAP HERE WHEN | |||
|
|
|
|
|
|
| SQUARE | IS | FLIPPED OVER IN DOTTED POSITION | |
WARNING: TO AVOID INJURY FROM UNEXPECT- ED STARTING OR ELECTRICAL SHOCK, DO NOT PLUG THE SAW IN UNTIL ALL ASSEMBLY AND
ALIGNMENT STEPS ARE COMPLETE. THE POWER CORD MUST REMAIN UNPLUGGED WHENEVER YOU ARE WORKING ON THE SAW.
Unpacking and Checking Contents
1.Separate all "loose parts" from packaging mater- ials and check each item with "Table of Loose Parts" to make sure all items are accounted for, before discarding any packing material.
WARNING: IF ANY PARTS ARE MISSING, DO NOT ATTEMPT TO ASSEMBLE THE BAND
SAW, PLUG IN THE POWER CORD, OR TURN THE SWITCH ON UNTIL THE MISSING PARTS
ARE OBTAINED AND ARE INSTALLED COR- RECTLY.
2.Remove front table and front cover first while saw is being unpacked. TO remove the front
cover, pull thecover at the neck and underside of throat area.