Craftsman 113.248510 owner manual Squaring the Blade to the Table

Page 32

ALL MODELS

10.Mount the front table to the base as follows:

a.Makesurefronttablelatchesarepositioned upas high as they will go.

b.Hold the front edge of the table. Position the rear

edge of the table so that the two flat springs slip under the two tabs on the rear table.

c.Line up the miter gage slots in the front and rear tables.

d.Push the front edge of the table backward and downward until the table snaps into position.

FRONT TABLE

SQUARING THE BLADE TO THE TABLE

WARNING: TO AVOID INJURY FROM UNEXPECTED

STARTING, MAKE SURE POWER CORD IS UN- PLUGGED BEFORE MAKING ADJUSTMENTS TO

BANDSAW PARTS.

To assu re repeatability and accuracy, it is important to square the blade to the table and adjust the 0° position stop. This will guarantee that the blade wi II return to the square position after the head has been moved for a bevel cut.

1.Locate the 1/4-20 x 1/2 oval point setscrew and use an 1/8-inch hex "L" wrench to install it in the

hole located at the left front of the rear table. -The setscrew has a lock patch that will make it hard to turn.

2.Slide the upper blade guard to its top most position and tighten knob.

3.Release bevel lock by pulling out bevel lock knob under left front edge of table.

4.Place a combination square on the table against the blade. Adjust the position of the blade to the

table by turning the handwheel. When the blade is flush against the combination square lock the bevel lock knob. Use a 1/8-inch hex "'L"wrench

to set the 0° stop. Turn screw until it makes contact with the frame.

5.Unlock bevel lock, bevel the blade, then return to 0° position. Push in bevel lock knob and recheck blade to make sure it is square to the table.

NOTE: The combination square must be "true" -- see the beginning of the unpacking and checking contents section for checking the combination square procedure.

 

I

il

/

 

l

ir,

0 ° STOP SETSCREW

i_/_

 

/"

32

Image 32
Contents 113.248440113.248510 Save This Manual For Future Reference113.248320 Table of Contents Know Your Power Tool Ground ALL Tools Keep Work Area CleanUSE Recommended Accessories Never Stand on Tool Keep Guards in PlaceAdditional safety instructions for band saw Before Using the SAWWhen Installing or Moving the SAW Before Each USEWhenever SAW is Running AccessoriesBefore Sanding Power Supply Glossary of terms for woodworkingMotor Safety Protection Wire SizesSawdust from interfering with normal motor ventila- tion 25 Ft 26 50 Ft 100 FtUnpacking and checking contents General informationLoose Parts Description QTYList of Loose Parts in BAG #507968 Truss Head Screw 1/4-20x12List of Loose Parts in BAG #508014 Pan Hd. Screw 10-32 xAssembly and alignment Nuts Support Bracke Leveling FootDescription Qty Truss Head Model 113.24821 OAttaching LEG SET Model Assembling Cabinet\ ,/o Ware Mounting the SAW to the CabinetFrom loose parts bag find the following hard Front Model 113.248210 only Attaching the HandwheelMounting the Motor Find the following partsModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Connecting the Motor Steps are CompletedRecommended Speed Settings Changing Speed SettingsModel 113.248320, 113.248440 Selecting Blade SpeedAttaching Trim Caps Getting to know your band saw MODELS113.248210an¢Location and function of the electronic indicator system Open Battery OpenBattery Cover Model 113.248440 & 113.248510 on LYUsing the Electronic Indicator System Function KeysRead-out Indicates correct tension for 3000Installing the Blade Jrt,tGU,DEsuPPO.TIIl-r L Upperblade tl tModel 113.248440 Aligning the Blade and Blade Guide AssembliesBlade Guide Mounting Front Turn front table over. Locate the two 2 latchSprings, two 2 alignment springs, and the four 4-20 8 hex washer Head thread forming ScrewsHead Capscrew Squaring the Blade to the Table Adjusting Front Table Model 113.248210 & 113,248320 ON-OFF SwitchLocation and function of controls Adjusting Bevel Lock Knob Basic band saw operation Sawdust CollectionCircle Cutting Operation Recommended Blade SizeInstalling Sanding Attachment Installing the Sanding BeltAdjusting the Upper Blade Guide Travel MaintenanceAdjusting Band SAW Bevel Travel Outlet Before Trouble Shooting Your Band SAW/SANDER Light BulbTrouble shooting--motor TroubleProbable Cause RemedyProbable Cause Suggested Corrective Action Trouble shooting -- electronicsProblem Suggested Corrective Action Trouble shooting ---electronics113.2485t Repair parts Parts List for Craftsman 12-INCH Band SAWKey Part Description LegPage Drive Assembly Parts KeyModel NOS .248210,113.248320, 113.248440 Base Assembly OMode1113.248320 Only ==Model113.248510 OnlyModel NOS .248210,113.248320,113.248440 Bevel Drive and Motor Mount Assembly Parts 9414202Parts List for Craftsman 12-INCH Electronic Band SAW Screw, Truss Hd /4-20 x 1/2Page Airs Part Numberpartdescription Model Name of Item