Craftsman 113.248510 owner manual Function Keys, Using the Electronic Indicator System, 3000

Page 25

FUNCTION KEYS

The five keys located to the right of the display are the function keys. They are:

io._o_ -- Turns the display "On" or "Off"

_j --Selects the Bevel Angle display

i-_. _j--Selects the Blade Tension display

E

_p_- Selects the Blade Speed display

-- Sets the Bevel Angle to Zero

NOTE: In order to extend battery life the display will shut off approximately five (5) minutes after the last key was pressed.

USING THE ELECTRONIC INDICATOR SYSTEM

1.Setting the Bevel Angle Reference Point. Whenever the battery is installed or a new zero

point is desired, it is necessary to set the zero reference. Normally the zero reference is set with the blade vertical to the table. When the blade is

in the desired position for the zero point do the following.

a. Press theIONIOFI¢key if display is off.

b. Press the _E._--_ key, then the ._,s_j key. c. Display should read: Fv 'U.U-'i

2. Selecting Blade Tension

n

a. Press the IoF_.IQFkey! if display is off.

b. Press the _ T,.

key.

c. The digital display will show one of seven tension settings. Turn the tension knob until the correct read-out appears for the blade or sanding belt you have selected.

Read-out

i Indicates correct tension for:

L

Loose - no

tension

S

Sanding

Belt

.125

1/8"

blade

.250

1/4"

blade

.375

3/8"

blade

.500

1/2"

blade

E

Overtensioned

3. Blade Speed

The digital display will read out one of two starting speeds, depending on where the motor belt is positioned on the pulleys. The two starting speeds are 3000 FPM and 1500 FPM. The speed ranges for each starting point are:

3000

1500

2800

1400

*2600

'1300

2400

1200

2200

1100

2OOO

1000

The band saw motor wilt stall if the blade speed drops two steps* below operating speed,

NOTE: It is important to maintain maximum cutting efficiency by keeping the blade speed as fast as possible. Do not feed the work piece too rapidly, tt will overload the motor and stall the blade,

25

Image 25
Contents 113.248320 Save This Manual For Future Reference113.248440113.248510 Table of Contents Keep Work Area Clean Know Your Power Tool Ground ALL ToolsUSE Recommended Accessories Never Stand on Tool Keep Guards in PlaceBefore Using the SAW Additional safety instructions for band sawWhen Installing or Moving the SAW Before Each USEBefore Sanding AccessoriesWhenever SAW is Running Glossary of terms for woodworking Power SupplyWire Sizes Motor Safety ProtectionSawdust from interfering with normal motor ventila- tion 25 Ft 26 50 Ft 100 FtGeneral information Unpacking and checking contentsDescription QTY Loose PartsTruss Head Screw 1/4-20x12 List of Loose Parts in BAG #507968List of Loose Parts in BAG #508014 Pan Hd. Screw 10-32 xNuts Support Bracke Leveling Foot Assembly and alignmentAttaching LEG SET Model 113.24821 ODescription Qty Truss Head Assembling Cabinet Model\ ,/o From loose parts bag find the following hard Mounting the SAW to the CabinetWare Front Attaching the Handwheel Model 113.248210 onlyMounting the Motor Find the following partsModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Steps are Completed Connecting the MotorChanging Speed Settings Recommended Speed SettingsModel 113.248320, 113.248440 Selecting Blade SpeedAttaching Trim Caps MODELS113.248210an¢ Getting to know your band sawOpen Battery Open Location and function of the electronic indicator systemBattery Cover Model 113.248440 & 113.248510 on LYFunction Keys Using the Electronic Indicator SystemRead-out Indicates correct tension for 3000Jrt,t Installing the BladeUpperblade tl t GU,DEsuPPO.TIIl-r LAligning the Blade and Blade Guide Assemblies Model 113.248440Blade Guide Turn front table over. Locate the two 2 latch Mounting FrontSprings, two 2 alignment springs, and the four 4-20 8 hex washer Head thread forming ScrewsHead Capscrew Squaring the Blade to the Table Adjusting Front Table Location and function of controls ON-OFF SwitchModel 113.248210 & 113,248320 Adjusting Bevel Lock Knob Sawdust Collection Basic band saw operationCircle Cutting Operation Recommended Blade SizeInstalling the Sanding Belt Installing Sanding AttachmentAdjusting Band SAW Bevel Travel MaintenanceAdjusting the Upper Blade Guide Travel Light Bulb Outlet Before Trouble Shooting Your Band SAW/SANDERTrouble Trouble shooting--motorProbable Cause RemedyProblem Trouble shooting -- electronicsProbable Cause Suggested Corrective Action 113.2485t Trouble shooting ---electronicsSuggested Corrective Action Parts List for Craftsman 12-INCH Band SAW Repair partsKey Part Description LegPage Key Drive Assembly PartsModel NOS .248210,113.248320, 113.248440 OMode1113.248320 Only ==Model113.248510 Only Base AssemblyModel NOS .248210,113.248320,113.248440 9414202 Bevel Drive and Motor Mount Assembly PartsScrew, Truss Hd /4-20 x 1/2 Parts List for Craftsman 12-INCH Electronic Band SAWPage Part Numberpartdescription Model Name of Item Airs